Instruction Manual
Table Of Contents
- ENGLISH
- 4 - COMPONENTS AND MAINTENANCE
- 4.1 - Fan motor assembly removal
- 4.2 - Heaters removal
- 4.3 - Drain pan removal
- 4.4 - Water Coil removal procedure
- 4.5 - Spigots Duct connection
- 4.6 - Rectangular flanges duct connection
- 4.7 - Optional filter and filter access
- 4.8 - Fresh air controller
- 4.9 - Optional water flow control valves
- 4.10 - Flexible pipe option
- 4.11 - Optional water sensor
- 4.12 - Optional condensate pump
- 3 - INSTALLATION OF THE UNIT
- 2 - SAFETY CONSIDERATIONS
- 1 - PRECAUTIONS
- 4 - COMPONENTS AND MAINTENANCE
- FRANÇAIS
- FRANÇAIS
- 1 - PRÉCAUTIONS
- 2 - MESURES DE SÉCURITÉ
- 3 - INSTALLATION DE L'UNITÉ
- 4 - COMPOSANTS ET MAINTENANCE
- 4.1 - Retrait du motoventilateur
- 4.2 - Retrait des résistances
- 4.3 - Retrait du bac d’évacuation
- 4.4 - Procédure de retrait de la batterie à eau
- 4.5 - Raccordement des gaines aux viroles
- 4.6 - Raccordement des gaines aux manchettes rectangulaires
- 4.7 - Option filtre et accès
- 4.8 - Régulateur d’air neuf
- 4.9 - Option vannes de régulation du débit d'eau
- 4.10 - Option tuyau flexible
- 4.11 - Option sonde d'eau
- 4.12 - Option pompe à condensat
- FRANÇAIS
- DEUTSCH
- DEUTSCH
- 1 - WICHTIGE HINWEISE
- 2 - SICHERHEITSHINWEISE
- 3 - INSTALLATION DES GERÄTES
- 4 - BAUTEILE UND WARTUNG
- 4.1 - Ausbau des Ventilators
- 4.2 - Ausbau der Heizelemente
- 4.3 - Ausbau der Kondensatwanne
- 4.4 - Austausch des Wasserregisters
- 4.5 - Kanalanschlussstutzen
- 4.6 - Rechteck-Kanalanschlussstutzen
- 4.7 - Optionaler Filter und Zugang zum Filter
- 4.8 - Außenluftmengenregler
- 4.9 - Optionale Wasservolumenstromregelventile
- 4.10 - Optionale Anschlussschläuche
- 4.11 - Optionaler Wassertemperatursensor
- 4.12 - Optionale Kondensat-Pumpe.
- DEUTSCH
- ESPAÑOL
- ESPAÑOL
- 1 - PRECAUCIONES
- 2 - CONSIDERACIONES DE SEGURIDAD
- 3 - INSTALACIÓN DE LA UNIDAD
- 4 - COMPONENTES Y MANTENIMIENTO
- 4.1 - Desmontaje del grupo motoventilador
- 4.2 - Extracción de los calentadores
- 4.3 - Extracción de la bandeja de drenaje
- 4.4 - Procedimiento de desmontaje de la batería de agua
- 4.5 - Espitas de conexión de los conductos
- 4.6 - Bridas rectangulares de conexión a los conductos
- 4.7 - Filtro (opción) y acceso al filtro
- 4.8 - Controlador de aire fresco
- 4.9 - Válvulas de control del caudal de agua (opción)
- 4.10 - Tubo flexible (opción)
- 4.11 - Sensor de agua (opción)
- 4.12 - Bomba de condensación opcional
- ESPAÑOL
4.11 - Optional water sensor
■ A water temperature sensor can be provided. It has
to be installed on the water circuit as described
below:
- For 2-pipe coil: the sensor shall be installed on a
cooling water pipe (for change-over function). The
sensor is installed on a part where the water ow
is continuous.
- For 4-pipe coil: the sensor shall be installed on a
heating water pipe (for cold-draft function that
prevents the operation of the unit when the heating
network is off).
NOTE: In case of unit with an electrical box (for
Carrier Thermostats), a “switch” is provided as an
option instead of the water sensor.
4.12 - Optional condensate pump
Check the sealing of the hydraulic connection of the
condensate pump and condensate recovery.
■ The meaning of the electrical wires is described
below:
- Brown - Blue wires: Electrical supply 230V
50/60Hz
- Black - Grey wires: Alarm contact Normally Closed
(NC) 250V/8A maxi.
4 - COMPONENTS AND MAINTENANCE
20