Product data

ManualsBrandsCarrier ManualsDomestic Appliances40MAQB12B--3

GUIDE SPECIFICATIONS

INDOOR FLOOR CONSOLE DUCTLESS UNITS

Size Range: 3/4 to 1 T on Nominal Cooling and Heating Capacity

Carrier Model Number: 40MB*F

PART 1 -- GENERAL

1.01 System Description

Indoor, wall-- mounted, direct-- expansion fan coils are matched with

a heat pump outdoor unit.

1.02 Agency Listings

Unit is rated per AHRI Standards 210/240 and listed in the AHRI

directory as a matched system.

1.03 Delivery, Storage, And Handling

Units are stored and handled per unit the manufacturer ’s

recommendations.

1.04 Warranty (For Inclusion B y Specifying

Engineer)

PART 2 -- PRODUCTS

2.01 Equipment

A. General:

Indoor, direct-- expansion, floor-- mounted fan coil. Unit is complete

with cooling/heating coil, fan, fan motor, piping connectors,

electrical controls, microprocessor control system, and integral

temperature sensing. Unit is furnished with integral mounting

bracket and mounting hardware.

B. Unit Cabinet:

Cabinet discharge and inlet grilles is attractively styled,

high--impact polystyrene. The cabinet is fully insulated for

improved thermal and acoustic performance.

CFans:

The fan is a tangential direct--drive blower type with an air intake in

the c ente r of the unit and a dis charge at the top and bottom front.

Auto mati c, motor--driven ve r tic al ai r swe ep i s provided s tanda rd.

Air sweep operation is user selectable. The vertical sweep may be

adjusted (using the remote control) and the horizontal air direction

may b e set manually.

D. Coil:

Coil are copper tube with aluminum fins and galvanized steel tube

sheets. Fins are bonded to the tubes by mechanical expansion and

blue hydrophilic pre--coated for enhanced wet--ability. A drip pan

under the coil has a drain connection for hose attachment to

remove condensate. The condensate pan has a internal trap.

E. Motors:

The motors are open drip--proof, permanently lubricated ball

bearing with inherent overload protection. The fan motors are

3--speed.

F Controls:

Controls consists of a microprocessor--based control system which

control the space temperature, determine optimum fan speed, and

run self diagnostics. The temperature control range is from 62_Fto

86_F(17_Cto30_C) in increments of 1_For1_C, and have 46_F

Heating Mode (Heating Setback). The wireless remote controller

has the ability to act as the temperature sensing location for room

comfort.

The unit shall have the following functions as a minimum:

1. An automatic restart after a power failure at the same

operating conditions as at failure.

2. A timer function to provide a minimum 24--hour timer

cycle for the system Auto Start/Stop.

3. Temperature--sensing controls that sense the return air

temperature.

4. Indoor coil freeze protection.

5. Wireless infrared remote control to enter set points and

operating conditions.

6. Automatic air sweep control to provide on or off activation

of the air sweep louvers.

7. De-- humidification mode provides increased latent removal

capability by modulating the system operation and set point

temperature.

8. Fan-- only operation to provide 6room air circulation when

cooling is not required.

9. Diagnostics provide continuous checks of unit operation

and warns of possible malfunctions. Error messages are

displayed at the unit.

10. Fan speed control is user--selectable: high, medium, low, or

microprocessor controlled automatic operation during all

operating modes.

11. Automatic heating--to-- cooling changeover in heat pump

mode. Control includes dead band to prevent rapid mode

cycling between heating and cooling.

12. The indoor coil high temperature protection is provided to

detect excessive indoor discharge temperature when the unit

is in heat pump mode.

G. Filters: The unit has a filter track with factory--supplied

cleanable filters.

H. Electrical Requirements: The indoor fan motor operates on

208-- 230V as specified. Power is supplied from the outdoor unit.

I. Operating Characteristics: The system has a minimum SEER

(Seasonal Energy Efficiency Ratio) and HSPF at AHRI conditions,

as listed on the specifications table.

J. Refrigerant Lines: All units has refrigerant lines that can be

oriented to connect from the left, right or back of unit. Both

refrigerant lines need to be insulated.

K. Special Features (Field Installed):

Condensate Pump: The condensate pump removes condensate

from the drain pan when gravity drainage cannot be used. The

pump is designed for quiet operation. The pump consists of two

parts: an internal reservoir/sensor assembly, and a remote

sound--shielded pump assembly. A liquid level sensor in the

reservoir stops the cooling operation if the liquid level in the

reservoir is unacceptable.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Catalog No.38MGQ---03PD

Replaces:38MG--- 02PD

Edition Date: 01/16