Specifications
3
B
A
2'-11
3
4
"
2'-7
1
8
"
4'-6
1
2
" C
1
C
2
MTG HOLES
L
C
9'-0
3
8
"
F
P
1'-3
3
4
"
BOTH ENDS
25
18
6
22
21
COOLER
E DIAM
L
C
PANEL
CONTROL
STOP BUTTON
START BUTTON
12
30
11
15
9
MTG HOLE
27
30
28
MN
30HS TOP VIEW
L
17
L
C
H
G
1'-1
3
8
"
4'-1
1
2
"
23
26
1'-1
1
4
"
1'-5"
1'-0
3
16
"
10
10"
3'-0"
2'-1
5
8
"
1'-6
1
4
"
K
C
L
REFRIG
DISCHARGE
30HS END VIEW
REFRIG
INLET
1'-7"
MTG
HOLES
L
C
16
24
FIELD WELDED
WATER
IN
WATER
OUT
ACCESSORY WATER MANIFOLDS AND CONDENSER
NOZZLE ARRANGEMENT VIEWED FROM FRONT
OF UNIT.
10
3
4
"
DIAM
CONDENSERC
L
6'-5
3
4
"
8
MTG HOLE
29
7
13
30HR TOP VIEW 30HR END VIEW
J
2'-6
3
4
"
MTG
HOLES
C
L
5
D
4
3
30HR , HS
FRONT VIEW
INLET
20
LEGEND
1 – 3-in FPT Water inlet 12 – Cut hole in removable plate for power inlet
2.1/2-in max conduit size
22 – Compressor no. 1:6 cylinder for
040, 050 and 060
2 – Temperature Controller Bulb
13 – Unloaded Solenoid. One on each compressor 23 – Compressor no 2:4 cylinder for
040, 050, 6-cylinder for 060
3 – 3 in FPT Water Outlet 14 – Oil safety Switches. Manual reset
(Std equipment on HS. accessory on HR)
24 –Liquid Line Solenoid Valve (one each CKT)
4 – 1-in FPT Water Drain Conn. 15 – 7/8-in ODF Refrigerant Liquid Inlet from
condenser circuit no. 1
25 – Water inlet Manifold (accessory) 4-in
150 lb ASA flat-face flange
16 – 7/8-in ODF Refrigerant liquid Inlet from
condenser circuit no. 2
26 – Water Outlet Manifold (accessory) 4-in
150-ib ASA flat-face flange
6 – 1/4-in SAE Flare Field Charging Valve (2) 17 – 1.3/8-in ODF Discharge Line. Circuit 1 and 2 27 – 5/8-in SAE Flare Pressure Relief Valve
(each condenser)
7 – Space required to remove cooler tubes
(either end)
8 – Space required to remove condenser tubes
(either end)
18 – Replaceable core Filter Driers, one each
circuit. HR, HS040 one core each HR
HS050 two cores circuit 1,one core
circuit 2 HR HS060 2 cores each
28 – 1/4-in Flare Conn. for water reg. valve
(each condenser)
9 – 2.1/2 - in diameter SCH 40 removable
nozzles (each end of both condensers)
19 – Compressor Sequence Switch 29 – 1/4-in Purge Valve (each condenser)
10 – Low Water Temp Cutout Bulb
1 –Three 7/8-in knockouts. Two on top and one
on back of control box
20 – Circuit Breakers
21 – Gage Panel (accessory) both sides
30 – Field Installed Control Transformer
(accessory). (In control panel,
adjacent to main terminal (block.)
Fig. 1 – Dimensions