Specifications

ManualsBrandsCarrier ManualsAir Compressor19XRV

NOTE: The default CCN Occupied Schedule OCCPC03S is

configured to be occupied (software versions 4.0 and later).

Input Service Configurations — The following con-

figurations require the ICVC screen to be in the SERVICE por-

tion of the menu.

• password

• input time and date

• ICVC configuration

• service parameters

• equipment configuration

• automated control test

PASSWORD — When accessing the SERVICE tables, a pass-

word must be entered. All ICVCs are initially set for a pass-

word of 1-1-1-1.

INPUT TIME AND DATE — Access the TIME AND DATE

table on the SERVICE menu. Input the present time of day,

date, and day of the week. The HOLIDAY TODAY parameter

should only be configured to YES if the present day is a

holiday.

NOTE: Because a schedule is integral to the chiller control

sequence, the chiller will not start until the time and date have

been set.

NOTE: The date format is MM-DD-YY for English units and

DD-MM-YY for SI units.

CHANGE ICVC CONFIGURATION IF NECESSARY —

From the SERVICE table, access the ICVC CONFIGU-

RATION screen. From there, view or modify the ICVC CCN

address, change to English or SI units, and change the pass-

word. If there is more than one chiller at the jobsite, change the

ICVC address on each chiller so that each chiller has its own

address. Note and record the new address. Change the screen

to SI units as required, and change the password if desired.

TO CHANGE THE PASSWORD — The password may be

changed from the ICVC CONFIGURATION screen.

1. Press the and softkeys. Enter the

current password and highlight ICVC CONFIGURA-

TION. Press the softkey. Only the last 5 entries

on the ICVC CONFIG screen can be changed: BUS

NUMBER, ADDRESS NUMBER, BAUD RATE, US

IMP/METRIC, and PASSWORD.

2. Use the softkey to scroll to PASSWORD. The

first digit of the password is highlighted on the screen.

3. To change the digit, press the

or softkey. When the desired digit is seen,

press the softkey.

4. The next digit is highlighted. Change it, and the third and

fourth digits in the same way the first was changed.

5. After the last digit is changed, the ICVC goes to the BUS

NUMBER parameter. Press the softkey to leave

that screen and return to the SERVICE menu.

TO CHANGE THE ICVC DISPLAY FROM ENGLISH TO

METRIC UNITS — By default, the ICVC displays informa-

tion in English units. To change to metric units, access the

ICVC CONFIGURATION screen.

1. Press the and softkeys. Enter the

password and highlight ICVC CONFIGURATION. Press

the softkey.

2. Use the softkey to scroll to US IMP/METRIC.

3. Press the softkey that corresponds to the units desired for

display on the ICVC (e.g., US or METRIC).

CHANGE LANGUAGE (ICVC Only) — By default, the

ICVC displays information in English. To change to another

Language, access the ICVC CONFIGURATION screen:

1. Press the and softkeys. Enter the

password and highlight ICVC CONFIGURATION. Press

the softkey.

2. Use the softkey to scroll to LID LANGUAGE.

3. Press the INCREASE or DECREASE softkey until the

desired language is displayed. Press to confirm

desired language.

MODIFY CONTROLLER IDENTIFICATION IF NECES-

SARY — The ICVC module address can be changed from the

ICVC CONFIGURATION screen. Change this address for

each chiller if there is more than one chiller at the jobsite. Write

the new address on the ICVC module for future reference.

INPUT EQUIPMENT SERVICE PARAMETERS IF NEC-

ESSARY — The EQUIPMENT SERVICE menu has six or

seven service tables depending on the ICVC software version.

Configure SERVICE Tables

— Access the SERVICE tables,

shown in Table 3, to modify or view job site parameters shown

in Table 12.

CHANGE THE BENSHAW INC., RediStart MX3™ SOFT-

WARE CONFIGURATION IF NECESSARY — Benshaw

starter configurations are checked and modified from the

menus in the Benshaw Redistart MX3 Default Display. See

Fig. 34 and Table 13 for default display and menu items. To ac-

cess the menus to perform checks and modifications, the Ben-

shaw starter must be powered up and its self-test must have

been successfully completed. The self-test takes place automat-

ically after power-up. Current and Ramp Time configurations

are entered in the CFN menu. CT Ratio configuration is en-

tered in the FUN menu. See Table 13 for menu structure and

Table 14 for settings.

1. Press the softkey until the desired menu is select-

ed on the display.

2. Press the softkey to access the displayed menu

items (Table 6).

3. Use the or arrow keys to scroll between menu items

until the desired item is reached on the display.

4. Press the softkey to access the value to be

changed.

5. Use the or arrow keys to adjust the new displayed

value. The key increases the value while the key de-

creases the value. Holding the arrow key will progres-

sively increase the rate of change. The value will stop

changing when either the factory set minimum or maxi-

mum value is reached. To make fine adjustments press

and release the arrow key.

6. When the correct value has been selected, press

the key to store the new configuration. At this

point, there are two options. The key will return

the display to the main display. The or arrow keys

will move the display to the next menu item. When fin-

ished press the key to return to the main display.

To view other settings and troubleshooting guide consult the

Benshaw RediStart MICRO instructional manual included in

the starter.

CAUTION

Be sure to remember the password. Retain a copy for

future reference. Without the password, access to the SER-

VICE menu will not be possible unless the ICVC_PSWD

menu on the STATUS screen is accessed by a Carrier

representative.

SERVICE

SELECT

ENTER

INCREASE

DECREASE

ENTER

EXIT

SERVICE

SELECT

ENTER

SERVICE

SELECT

ENTER





ENTER









ENTER



