Datasheet
2 Specifications are subject to change without notice (06.10.08)
DIB01, PIB01
Power supply Overvoltage cat. III
Rated operational voltage (IEC 60664, IEC 60038)
through terminals:
A1, A2 or A3, A2 (DIB01)
2, 10 or 11, 10 (PIB01)
D48: 24 to 48 VAC/DC ± 15%
45 to 65 Hz, insulated
B23: 115/230 VAC ± 15%
45 to 65 Hz, insulated
Dielectric voltage
DC supply AC supply
Supply to input 2 kV 4 kV
Supply to output
4 kV 4 kV
Input to output
4 kV 4 kV
Rated operational power
AC 4 V
A
DC
3 W
Supply Specifications
Power ON delay 1 s ± 0.5 s or 6 s ± 0.5 s
Reaction time (input signal variation from
-20% to +20% or from
+20% to -20% of set value)
Alarm ON delay < 100 ms
Alarm OFF delay < 100 ms
Accuracy (15 min warm-up time)
Temperature drift ± 1000 ppm/°C
Delay ON alarm ± 10% on set value ± 50 ms
Repeatability ± 0.5% on full-scale
Indication for
Power supply ON LED, green
Alarm ON LED, red (flashing 2 Hz
during delay time)
Output relay ON LED, yellow
Environment (EN 60529)
Degree of pr
otection IP 20
Pollution degree 3 (DIB01), 2 (PIB01)
Operating temperature -20 to 60°C, R.H. < 95%
Storage temperatur
e
-30 to 80°
C, R.H. < 95%
Housing
Dimensions DIB01
22.5 x 80 x 99.5 mm
PIB01
36 x 80 x 94 mm
W
eight
Approx. 150 g
Screw terminals
Tightening torque Max. 0.5 Nm
acc. to IEC 60947
Approvals UL, CSA
CE Marking Yes
EMC
Electr
omagnetic Compatibillity
Immunity According to EN 61000-6-2
Emission According to EN 61000-6-3
General Specifications
Output SPDT relay
Rated insulation voltage 250 VAC
Contact ratings (AgSnO
2
)µ
Resistive loads AC 1 8 A @ 250 VAC
DC 12 5 A @ 24 VDC
Small inductive loads AC 15 2.5 A @ 250 VAC
DC 13 2.5 A @ 24 VDC
Mechanical life ≥ 30 x 10
6
operations
Electrical life ≥ 10
5
operations
(at 8 A, 250 V, cos ϕ = 1)
Operating frequency ≤ 7200 operations/h
Dielectric strength
Dielectric voltage
≥ 2 kVAC (rms)
Rated impulse withstand volt. 4 kV (1.2/50 µs)
Output Specifications
Measuring ranges (cont.)
Standard CT (examples) AAC
rms
Max. curr.
T
ADK2 50 A/5 A 5 to 50 A 60 A
C
TD1 150 A/5 A 15 to 150 A 180 A
C
TD4 400 A/5 A 40 to 400 A 480 A
TAD12 1000 A/5 A 100 to 1000 A 1200 A
TACO200 6000 A/5 A 600 to 6000 A 7200 A
N
ote:
The input voltage cannot
raise over 300 VAC/DC with
respect to ground (PIB01 only)
Contact input
DIB01 Terminals Z1, Y1
PIB01 Terminals 8, 9
Disabled > 10 k
Ω
Enabled < 500 Ω
Latch disable > 500 ms
Input Specifications (cont.)