Installation Instructions

ManualsBrandsCARLO GAVAZZI CONTROLS ManualsElectronicsCarpark Wireless Display Interface, Model no. SBP2WDI48524

Carlo Gavazzi Controls S.p.A.

SBP2WDI48524

SBP2WDI48524 ENG14/12/2018

Dupline

Carpark Wireless Display Interface

Description

The SBP2WDI48524 wireless display interface

module is part of the Dupline

Carpark system

which contains other variants of sensors,

controllers and displays.

The SBP2WDI48524 wireless module works with

the wireless master SH2WBU230N which acts as

a generator for wireless modules.

The wireless transmission can reach up to 700 m

in the open air between the wireless master and

the wireless modules.

Also, the SBP2WDI48524 is a Dupline

to Modbus

RTU converter and acts as an interface between

Dupline

and the Carpark displays.

The module is connected to the display via RS485

and is normally installed close by, but can be

installed up to 300m from the display.

Benets

• Plug and play installation

• Wireless transmission range <700 m in open air

• Can be mounted up to 300 m away from the display

• LEDs for indication of communication status

• Compact 2-DIN housing suitable for a decentralised

installation

Applications

Parking Guidance Systems

Main functions

Acts as a wireless interface between Dupline

and the carpark displays

Summary of content (8 pages)

PAGE 1
SBP2WDI48524 Dupline® Carpark Wireless Display Interface Benefits • • • • • Plug and play installation Wireless transmission range <700 m in open air Can be mounted up to 300 m away from the display LEDs for indication of communication status Compact 2-DIN housing suitable for a decentralised installation Description The SBP2WDI48524 wireless display interface module is part of the Dupline® Carpark system which contains other variants of sensors, controllers and displays.
PAGE 2
SBP2WDI48524 Features Power Supply Rated operational voltage Rated operational power Reverse-polarity protection Connection Power-ON delay Power-OFF delay No isolation between power supply and RS485 Standard compliance 24 VDC (±20%), 20 mA, CL.2 400 mW (display excluded) Yes A1 (+) 24 VDC A2 (-) 24 VDC A (-) RS485 bus for display B (+) RS485 bus for display GND 24 (internally connected Max 5.5 A + display) Make sure that you use the correct power supply.
PAGE 3
SBP2WDI48524 LED indication Green LED Blue LED Yellow LED Power status Short blinking Long blinking ON Steady OFF Slow blinking ON: Power ON OFF:Power OFF Configured and working Module not configured Only during configuration communication OK No communication on RS485 Tx OK but no reply from the display Environmental Ambient temperature Degree of protection Pollution degree Humidity (not condensing) Dielectric strength -40°... +50°C (-40°... +122°F) -50° ... +85°C (-58° ... +185°F) IP20 3 20 ...
PAGE 4
SBP2WDI48524 Mechanics Housing Dimensions Housing material Degree of protection Front Weight Colour 2-DIN module Noryl SE1 Screw terminal IP20 IP50 210 g with antenna Grey 2470 / RAL7035 Dimensions (mm) 35 45.0 5.0 .0 45.0 90.0 90.0 .0 5.0 35.0 44.0 14.5 44 .5 14 14/12/2018 SBP2WDI48524 ENG Carlo Gavazzi Controls S.p.A.
PAGE 5
SBP2WDI48524 Wiring H A1 A2 + - A 24V B F B+ E D C GND A- G A B C D Internal jumper Max 5.5 A Cable distance between display and module is max 300 m. White Yellow E Green F Brown G H Display Wireless connection Connection Terminal Cable cross-section area Tightening torque RS485 cable 14/12/2018 SBP2WDI48524 ENG 6-screw type Max. 1.5 mm2 0.4 Nm / 0.8 Nm Max 300 m from module to display Carlo Gavazzi Controls S.p.A.
PAGE 6
SBP2WDI48524 Compatibility and conformity Approvals Standards Approvals IEEE 802.15.4 UL notes • This product is intended to be supplied by a Listed Information Technology Equipment AC Adaptor marked NEC Class 2 or LPS • Max ambient temperature: 50°C (122°F) 14/12/2018 SBP2WDI48524 ENG Carlo Gavazzi Controls S.p.A.
PAGE 7
SBP2WDI48524 Mode of operation The SBP2WDI48524 is a wireless Dupline® to Modbus RTU converter that is used as an interface between Dupline® and the carpark displays. The module has no DIP-switch settings, but is configured from the SBP2WEB24 controller configuration software. Each display must be connected to one SBPW2DI48524 module and it can be connected in close range from the display or in a cabinet in a far distance from the display.
PAGE 8
SBP2WDI48524 References Product selection key SBP2WDI48524 COPYRIGHT ©2017 Content subject to change. Download the PDF: www.productselection.net 14/12/2018 SBP2WDI48524 ENG Carlo Gavazzi Controls S.p.A.