Product Manual

技术要求
序号
材 质
豪华中性
中英文说明书
部件名称
丝 印 要 求 部件图示/字符图示
1
尺寸
设计
审核
版 权 所 有
权项
权责人
时 间
产品名称
料号
深圳市华思 旭 科技有限 公 司
批准
钟文彬
描述
文件
编号
版本号
HSX-RD-SC-
157铜板 单黑 如图 75*105m m
豪华 中性
中英 文说明书
豪华 中性
中英 文说明书
不带 容量,输入14V 1 A
手机 转接头1拖3
电瓶 夹带防反 充
4.07.02.01.0034
3.28
E-Power Charging Instruction：
1. Plug the home adaptor into the universal socket.
2. Connect 15V 1A input port of E-Power to the other end of home
adaptor .
Or
1. Plug the car adaptor into the socket of cigarette lighter.
2. Connect 15V 1A input port of E-Power to the other end of car
adaptor.
B. OPERATION GUIDANCE
Indicator
Press the switch to check the storage level of E-Power
The indicator will flash one by one during the period of charging.
Different number of solid indicators show different storage level
of E-Power. All indicators light off when the charging is paused or
completed.
S 0% 10% 20% 40% 60% 80% 100%
Indicator Unlit 5 Flashing 1 solid 2 solid 3 solid 4 solid 5 solid
torage level
Jump start 12V gasoline vehicle Instruction:
1. Make sure that the number of indicators is not less than 3
ones.
2. Connect the RED clamp to the vehicle's battery positive (+)
terminal and connect the BALCK clamp to the vehicle's
battery negative (-) terminal.
3. Plug the cord of jumper cable into the jump start socket.
2
Fuse Protecti on
Overch arge and
Overdi scharge Protection
Agai nst-reverse Plug
Applied Standard：GB/T 18287-2000
I. WARRANTY INFORMATION:
1.We offer a limited warranty for this product against any defects in material
and workmanship for a period of ____ months from the date of purchase by the
end user/consumer. The conditions of the warranty are as follows:
2.The warranty is only valid upon presentation of the original receipt (from
dealer/retailer) by the original purchaser with the product to be repaired or
replaced
3.The warranty is void if the serial number, date of purchase and label has
been removed
4.The warranty does not cover damage or product failure resulting from normal
wear and tear, physical abuse, improper installation, misuse, modification or
repairs by unauthorized third parties
5.We do not assume responsibility for any loss or damage incurred during
shipment or as a result of a force majeure
6.We are not liable for any incidental or consequential damages arising from
the use or misuse of this product
7.All warranty claims are limited to repair or replacement of the defective
product and at the sole discretion of us
8.If we repair or replace the product, the product will be covered for the
remaining time of the original warranty period. Repair or replacement may
involve the use of reconditioned units which are equivalent in function.
Replaced part or product becomes the property of us
9.Consumable components such as batteries are not covered by the warranty
7
Only for charging/power supply to 19V Notebook
1. Plug the switch cable A to USB 19V 3.5A output port.
2. Select appropriate connector for your Notebook and connect
it to the switch cable A and your Notebook.
3. Press the switch button to charge/power supply.
4. Start the vehicle
5. When the vehicle is started, remove jumper cable from
E-Power and disconnect red and black clamps to the vehicle
battery terminals.
6. Leave the vehicle's engine running
Charging Cell Phone or Tablet Instruction:
1. Plug the switch cable B to USB 5V 2A output port.
2. Select appropriate connector and connect it to your mobile
phones or tablet.
3. Press the switch button to charge.
3
1 2
3
4 5
H. Warning:
1. Always make sure the blue plug of jumper cable connect with
the jump start socket tight in EPower before jumping start the
vehicle. Otherwise, it will affect the results, even causing the
melt of the blue plug.
2. Always check if the jumper clamps are well connected, check if
the vehicle battery connector is rusted or dirty, clean it before
jumping start the vehicle. DO NOT jump start again after 3
attempts. Otherwise, it will damage the host. And Check your
vehicle if it has other trouble.
3. DO NOT connect the two clamps. Otherwise, it may be
dangerous!
4. DO NOT disassemble the host. Otherwise, it may be
dangerous!
Always take care when using the appliance
This appliance is not intended for use by young or infirm persons without
supervision
Do not use as a toy
Do not allow the appliance to become wet
Do not immerse the appliance in water
Do not operate the appliance in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust
Do not modify or disassemble EPower. Only a repair technician may
repair this unit
Do not expose the appliance to heat
Do not store in locations where the temperature may exceed 70 °C
Charge only at ambient temperatures between 0 °C and 40 °C
Charge only using the charger provided with the appliance
Under extreme conditions, battery leakage may occur. Carefully wipe the
liquid off using a cloth and avoid skin contact when you notice liquid on
the batteries. In case of skin or eye contact, rinse immediately with clean
water and seek medical attention
At the end of their useful life, discard the appliance with due care for our
environment
6
!
!
!
!
Q. How many times can this appliance charge for my cell phone?
A. Approx. 7 times for iPhone4.
Q. How long will this appliance take to charge my mobile phone full?
A. Approx. 1 hour
Q. How long will this appliance on a full charge take to supply the
Notebook?
A. 2-3 hours
Q. How many times can this appliance jump start the vehicle if it is
in full battery?
A. Approx. 20 times.
Q. How long the storage of battery will remain?
A. 6-12 months, however, we suggest to recharge it every 6 months.
F. TROUBLE SHOOTING:
Finding Cause Remedies
E-Power is still not full
charged while its 5
indicator lights are
solid.
No response when
pressing the switch
button.
E-Power is a bit hot
when charging for
Notebook.
60% charging for longer storage
of EPower when no usage.
Low voltage protection of
EPower is started.
The charging current is a bit
high (3.5A)
Unplug the ad aptor and
plug it again .
Plug the adap tor into the
14V 1A input por t to
activate.
Remove th e bat tery of your
Noteboo k and u se this
applian ce to s upply powe r
directl y, or disc onnect EPower
with your N ote book and
connect them w hen it is cool .
5
G. TOXIC AND HARMFUL SUBSTANCES:
O：Indicate all homogeneous materials' hazardous subs tan ces c ont ent a re below the MCV limit specified
in the Standard 2002/95/EC(RoHs).
Composition and amount of toxic and harmful substances in EPower
Pb Hg Cd Cr(Vi) PBB PBDE
O O O O O O
LED flash light
Press the switch 3 seconds to start the LED flash light.
There are 4 modes of LED light appear in order (normal. strobe.
SOS. off) if you press slightly.
For power supply to 12V vehicle products or 12V electronics
1. Plug the optional switch cable to 12V 10A output port.
2. Connect the optional switch cable and 12V vehicle product
or 12V electronics.
3. Press the switch button to power supply.
C. PARTS LIST ：
#
1 1
3 1
4 otebook 8
Parts Name Quantity
2 1
Host
Switch cabl e A
Switch cabl e B
N connector
#
5 1
6 1
7 1
1
Parts Name Quantity
Home adaptor
Car adaptor
Jumper ca ble w ith clamps
8 User Manual
4
E. FAQ：
Q. How to turn off this appliance?
A. This appliance will power off automatically when no load or
charging is complete
D. TECHNICAL SPECIFICATIONS：
Size： 160*75*28mm
Weight： 420g
Battery Capacity：37Wh
Output: 5V 2A; 12V 10A ; 19V 3.5A;
Input： 15V 1A
Full charging time： 3 hours
Starting current： 200A
Peak current： 400A
Operating temperature : -20℃ ~ 60℃
USER MANUAL
Thank you for choosing the E-Power! Always follow
b a s i c sa f e t y p r e c a u t i o n s w h e n us i n g e l e c t r i c a l
appliances. Read all instructions carefully, Please keep
this instruction manual for easy reference
USB5V 2A output port
15V 1A input port
12V 10A output port
Switch
Jump start socket
Indica to r
19V 3.5A output port
A. PRODUCT LAYOUT：
For 12V vehicle products
Home adaptor Car adaptor
Jumper cable w it h cl am ps
Switch cable A
Switch cable B
1
LED Flash Light