User manual

7
ENG
“UEX-PLUS” +03U220621 - rel. 1.4 - 04.08.2009
installeruserservice
1. INTRODUCTION AND ASSEMBLY
1.1 humiSteam x-plus (UEX*)
Range of isothermal immersed electrode humidiers with liquid crystal
display for the control and distribution of steam.
Models available (identiable from the code shown on the product):
UE001, UE003, UE005, UE008, UE009, UE010, UE015, UE018: steam
•
production capacity up to 18 kg/h (39.7 lb/h), water connections under
the base of the humidier;
UE025, UE035, UE045, UE065: steam production capacity from 25 to 65 kg/h •
(55.1 to 144.3 lb/h), water connections on the side of the humidier;
UE090, UE130: steam production capacity from 90 to 130 kg/h (198.4 to •
286.6 lb/h), water connections on the side of the humidier.
1.2 Dimensions and weights
All dimensions are given in millimeters and the inch dimensions are in
parenthesis.
Models UE001 to UE018
UE001 to UE008 UE009 to UE018
dimensions
mm (in)
A 365 (14.4) 365 (14.4)
B 275 (10.8) 275 (10.8)
C 620 (24.4) 712 (28.0)
weights kg
(lb)
packaged 16 (35.3) 20 (44.0)
empty 13.5 (29.8) 17 (37.5)
installed* 19 (41.9) 27 (59.5)
Models UE025 to UE065
Fig. 1.b
UE001 to
UE008
UE009 to
UE018
UE025 to
UE045
UE045** to
UE065
dimensions
mm (in)
A 365 (14.4) 365 (14.4) 545 (21.5) 635 (25.0)
B 275 (10.8) 275 (10.8) 375 (14.8) 465 (18.3)
C 620 (24.4) 712 (28.0) 815 (32.0) 890 (35.0)
weights
kg (lb)
packaged 16 (35.3) 20 (44.0) 39 (86.0) 51 (112.4)
empty 13.5 (29.8) 17 (37.5) 34 (74.9) 44 (97.0)
installed* 19 (41.9) 27 (59.5) 60.5 (133.4) 94 (207.2)
Models UE090 to UE0130
UE090 UE130
dimensions
mm (in)
A 1150 (45.3) 1150 (45.3)
B 465 (18.3) 465 (18.3)
C 890 (35.0) 890 (35.0)
weights kg
(lb)
packaged 77 (169.8) 81 (178.6)
empty 70 (154.3) 74 (163.1)
installed* 130 (286.6) 170 (374.8)
*: in operating conditions
**: 230 Vac model
1.3 Opening the packaging
make sure the humidier is intact upon delivery and immediately notify o
the transporter, in writing, of any damage that may be due to careless or
improper transport;
move the humidier to the site of installation before removing from the o
packaging, grasping the neck only from underneath the base;
open the cardboard box, remove the protective material and remove the o
humidier, keeping it vertical at all times.
1.4 Positioning
the unit is designed to be mounted on a wall that is strong enough to •
support the weight in normal operating conditions (see Wall-mounting
below). Models UE025 to UE0130 can stand on the oor;
to ensure correct steam distribution, position the humidier near the •
point of steam distribution;
make sure the humidier is level, allowing the minimum clearances (see •
Fig. 1.d) for maintenance operations.
Important: during operation the metal casing heats up and the rear
part resting against the wall may reach temperatures in excess of 60
°C (140 °F) .
Distances from walls
Models UE001 to UE018 Models UE025 to UE130
≥ 200
(7.9”)
<0,5°
≥ 200
(7.9”)
≥ 200
(7.9”)
≥ 400
(15.7”)
≥ 700
(27.6”)
≥ 200
(7.9”)
≥ 200
(7.9”)
≥ 700
(27.6”)
≥ 200
(7.9”)
Fig. 1.d
1.5 Wall-mounting
Fit the humidier on the wall using the support bracket and the screw kit
supplied (for the dimensions see Fig. 1.d).
Assembly instructions:
unscrew the wall bracket from the humidier bracket;1.
fasten the wall bracket (see Fig. 1.e), checking horizontal position with 2.
a level; if installed on a masonry wall, the plastic anchor plugs (dia. 8
mm/0.31” ) and screws (dia. 5 mm x L= 50 mm/ 0.19” x L= 1.97” ) supplied
can be used;
hang the appliance to the bracket using the slot on the top edge of the 3.
rear of the appliance;
secure the appliance to the wall through the hole in the center on the 4.
rear of the unit. For the weights and dimensions see Figs. 1.a, 1.b, 1.c.
The supplied wall anchors and screws should only be used on
concrete walls.
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
B
A
C
Fig. 1.a
Fig. 1.c