User manual

17
GB
“Wellness” +030220571 - rel. 3.0 - 01.10.2007
installeruserservice
5. REMOTE TERMINAL, GSM MODEM AND SUPERVISORY NETWORK
5.1 Remote display terminal
The display terminal can be detached from the humidi er and moved to
another place.
Depending on the distance required, the following are necessary:
up to 50 metres: 6-wire telephone cable and two ferrites (code
0907858AXX) (see Fig. 5.a);
up to 200 metres: two CAREL TCONN6J000 boards, 6-wire telephone
cables and an AWG20-22 shielded cable with 3 twisted pairs (for the
connection of the two boards, Fig. 5.b).
Note: to  ll the empty space left by the display terminal on the
humidi er, use CAREL kit code HCTREW0000.
Remote connection of the terminal up to max 50 m
J18
humiSteam Wellness
3
2
1
2
Fig. 5.a
Key:
1 telephone cable (up to 50 m distance);
2 two ferrites (code 0907858AXX) to be applied to the ends of the
telephone cable;
3 remote display terminal.
Remote connection of the terminal up to 200 m
J18
humiSteam Wellness
4
2
2
A
J14
1 2 3 1 2 3
J15
B
C
SC
A
J14
1 2 3 1 2 3
J15
B
C
SC
5
3
3
1
Fig. 5.b
Key:
1 telephone cable (up to 0.8 m distance);
2 CAREL TCONN6J000 board;
3 pin strip J14 and J15 in position 1-2 (power supply available on the
telephone connectors A, B and C and screw SC);
4 AWG20-22 shielded cable with 3 twisted pairs to move the display
terminal up to 200 m away. Connection to the TCONN6J00 board:
terminal SC function
0 EARTH (shield)
1 +VRL
2 GND
3 RX/TX-
4 RX/TX+
5 GND
6 +VRL
5 remote display terminal
•
•
5.2 GSM network connection (send SMS)
The humidi er can be con gured to send SMS message for alarms and
malfunctions (see par. “7.10”, page 25).
humiSteam Wellness
J19
1
2c
3
M
O
D
E
M
2a
2d
2b
Fig. 5.c (inside humidi er, electrical compartment)
Key:
1 electronic board PCOI00MDM0 (to be connected to connector J19 on
the humidi er board)
2
CAREL GSM kit PLW0P65M00, made up of:
2.a modem
2.b antenna (with magnetic base)
2.c serial cable
2.d power supply
•
•
•
•
•
3 SIM card to be inserted in the modem. Make sure that the access
password (PIN number) is not enabled
5.3 Supervisory network (J19)
The humidi er can be connected to the following optional boards:
PCOS004850 for CAREL connections;
PCOS004850 for Modbus® connections;
PCO10000F0 for Lon connections;
PCO100MDM0 for RS232 connections;
PCOS004850 for Winload connections.
M.2 M.7
J19
M.8
Fig. 5.d (detail of the electronic board, humidi er electrical compartment)
Important: for the tLAN and pLAN connections in residential
household (IEC EN 55014-1) and residential (IEC EN 61000-6-3)
environments, use shielded cable (with shield connected to GND). This
warning also applies to the cables leaving the unit.
•
•
•
•
•