™ TeamSet PRO ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
Congratulations and thank you for choosing the scala rider TeamSet pro Bluetooth® Headset package for bikers. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider TeamSet pro. This retail box contains two scala rider TeamSet pro headsets that already factory paired (see details below).
SET UP AND CONFIGURATION 1 Dual Wall Charger 2 Allen Wrenches 2 sets of Velcro Pads GPS 2 MP3 Cables Mobile phone 2 MP3 Cable Holders 2 Glue Plates 2 Pre-moistened Towelettes 2 Carry-Pouches 4 Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form MP3 player Driver-toPassenger Full-duplex Intercom Connection IMPORTANT: The cover tongue protecting the Charging Jack should be kept tightly closed at all times to
NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. SET UP FOR MOBILE PHONE CALLS: PAIRING If you have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the scala rider TeamSet pro, you must first pair your headset to the mobile phone. NOTE: If you have a compatible Bluetooth GPS device you wish to use with the scala rider TeamSet pro, please skip this step, and continue ahead to SET UP FOR BLUETOOTH GPS DEVICE.
4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros). 5. Your GPS device will confirm that pairing has succeeded. The headset will begin flashing slowly in Blue. 6. If you wish to use a Bluetooth mobile phone to make and receive calls through the headset, you must now pair your mobile phone to your GPS device by following your GPS and/or mobile phone’s instructions. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode.
4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly. 5. Peel the foil cover from the Glue Plates’ adhesive pad. 6. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. Using two speakers inside the helmet may be prohibited in certain jurisdictions.
USING THE HEADSET GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: REQUIRED ACTION: Turn on the headset Press the CTRL Button steadily for at least three seconds Turn off the headset Press the CTRL Button steadily for at least three seconds Increase the volume Tap the Volume Up Button Decrease the volume Tap the Volume Down Button AGC (Automatic Gain Control): In addition to manual Volume Control, the scala rider TeamSet pro will automatically increase and reduce its volume according to ambient noi
First, make sure your microphone is located properly in front of the center of your mouth. The scala rider TeamSet pro is designed for use in loud environments. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections.
USING THE MP3 PLAYER WITH YOUR HEADSET Your scala rider TeamSet pro headset can be connected to an MP3 player device by plugging it to the Helmet Clamp’s jack with the MP3 cable. At your option, you may further secure the MP3 cable by using the MP3 cable holder. For this purpose please proceed as follows: 1. Use the enclosed Allen Wrench to remove both Allen screws from Helmet clamp and release the clamp’s back plate. 2. Place the MP3 cable holder on the MP3 cable holder hook helmet clamp.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada (IC) Statement 15.
By way of purchasing this Device and not returning it for a full refund (see below), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of
