™ Q2 MultiSet pro ™ communication in motion ™ Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario User Guide
© Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Cardo Systems, Inc. is under license. Other trademarks and trade names are those of their respective owners.
Congratulations and thank you for choosing the scala rider Q2 MultiSet pro Bluetooth® Headset package. This User Guide will help you operate the headset, but you should first familiarize yourself with the Bluetooth® functionality of your cellular phone and/or GPS device before using the scala rider Q2 pro. This retail box contains two scala rider Q2 pro headsets that already factory paired (see details below).
SET UP AND CONFIGURATION 2 Wall Chargers 2 Allen Wrenches 2 sets of Velcro Pads 2 MP3 Cables 2 MP3 Cable Holders Mobile phone & A2DP connectivity 2 Glue Plates 2 Pre-moistened Towelettes 2 Carry-Pouches 4 Microphone Sponges Flat sponge for full-face helmets and round sponge for other helmet types User Guide, including Warranty and Registration form Built-in FM radio Driver-toPassenger Full-duplex Intercom Connection scala rider Q2 pro or other scala rider headset GPS MP3 player Bike-to-Bike Intercom
Your MultiSet pro units are already factory paired and ready for use. If for any reason, you have to pair them again, proceed as follows: 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3.
Manual Connect Intercom can be initiated from either headset by pressing the MC button for scala rider Q2 pro and CTRL button for any earlier scala rider headset. RESET INTERCOM PAIRING You can delete all of the headset’s Intercom pairings at any time. 1. With the scala rider Q2 pro headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 2. Press and hold the Volume Up Button for three seconds. 3.
GETTING STARTED ATTACHING THE CLAMP ON THE HELMET The Helmet Clamp must be attached to the left side of the helmet. Once attached, the headset unit can be mounted or released from the Helmet Clamp at any time. If you wish to connect your MP3 player to your headset, please refer first to the assembly instructions listed in section: CONNECTING YOUR MP3 PLAYER TO YOUR HEADSET.
not horizontally (Be sure to clean the selected area prior to the gluing process). 4. Use the pre-moistened Towelette to clean the helmet area where you want to install the Glue Plate. Allow to dry thoroughly. 5. Peel the foil cover from the Glue Plates’ adhesive pad. 6. Place the Glue Plate into position according to #3. Press firmly 15 seconds on all 3 parts of the Glue Plate. 7. The adhesive pad bonds to full strength over the next 24 hours.
Press here to remove USING THE HEADSET GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Increase the volume Decrease the volume REQUIRED ACTION: Press the CTRL Button steadily for at least three seconds Press the CTRL Button steadily for at least three seconds Short press the Volume Up Button Short press the Volume Down Button AGC (Automatic Gain Control): In addition to manual Volume Control, the scala rider Q2 pro will automatically increase and reduce its volume
NOTE: When using a scala rider Headset (not a Q2 pro version) as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 pro headset. Manual Connect Intercom can be initiated from either headset. Initiate Intercom calls from scala rider Q2 MC Button Connect: Tap twice the MC Button to open an intercom call (wait 3 seconds between taps). To terminate the call, tap once.
PHONE FUNCTIONS Answer a call Reject a call Terminate a call Voice Dial Redial Tap the CTRL Button or speak loudly any word of your choice during an incoming call. Tap the MC Button or remain silent for 15 seconds during an incoming call. Tap the CTRL Button to end a call. During Standby, Tap the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature.
The RDS feature is set OFF by default Turning the FM Radio On While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio. Turning the FM Radio Off While the radio is turned on, press and hold the MC button for three seconds to turn the Radio off.
Pairing the Headset to an MP3 Player or Adapter 1. Turn on your MP3 Player or Adapter, and make sure that its Bluetooth function is activated. 2. With the scala rider Q2 pro headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin alternating rapidly: 3. Search for Bluetooth headsets on your MP3 Player by following the device’s instructions. NOTE: For use of a Bluetooth adapter, follow the device’s instructions. 4.
7. Tuck the MP3 cable into the hook of the MP3 cable holder. 8. In order to use your MP3 player, power on the headset to have it on Standby mode, flashing slowly in Blue. NOTES: • Operate the MP3 Player device by using its buttons (FF/REW/PLAY/PAUSE). • Volume can only be adjusted through the MP3 Player. • Any other audio connection will automatically mute the MP3 Player. The audio signal will return only when headset is once again in Standby mode.
• Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device. IC RF Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL. Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
