DIGITAL PHYSICIAN Waist-High Scale Model 8430 Series Operating Instructions 8525-M041-O1 Rev L 02/15 CARDINAL SCALE MFG. CO. PO BOX 151 WEBB CITY, MO 64870 PH (417) 673-4631 FAX (417) 673-5001 www.detectoscale.com Technical Support: Ph: 866-254-8261 techsupport@cardet.
0033-M114-O1 Rev G Model 6437 Series
FCC COMPLIANCE STATEMENT This equipment generates uses and can radiate radio frequency and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
0033-M114-O1 Rev G Model 6437 Series
INTRODUCTION Thank you for purchasing our Detecto Model 8430 Series Digital Physician Waist-High Scale. It has been manufactured with quality and reliability at our factory in Webb City, MO USA. Your scale has been tested before leaving our factory to insure accuracy and dependability for years to come. This manual is provided to guide you through the operation of your scale. Please read it thoroughly before attempting to operate your scale and keep it handy for future reference.
UNPACKING INSTRUCTIONS Remove scale from carton by lifting up with equal force from column and platform base. Check for any damage incurred in shipping. If scale has been damaged, place a claim with the carrier. Use the original carton and shipping material to return the scale. Remove all plastic wrapping, foam fillers and cardboard material from the scale.
ASSEMBLY INSTRUCTIONS, CONT. Grommet Load Cell Cable C Figure No. 1 Figure No. 3 Column Raise Draft Rod Draft Rod Push Lever Column Bracket Opening Figure No. 4 Swivel Ball Socket and Scale Top Plate #10-32 Truss Head Screw Figure No.
OPERATION MedVue MV1 Keypad Basic Operation To Weigh 1. Press ON/OFF key to turn the MV1 on. 2. Press ZERO key to zero weight display. ZERO, GROSS and lb or kg annunciator will turn on to show that the scale is ready for use. 3. Place patient on scale and read weight display. 4. If a printer is connected to scale, press PRINT/ENTER key to print a ticket. 5. Remove patient from scale. Zero Weight Display 1. In Gross Weight mode (GROSS annunciator on), press ZERO key. 2. Weight display will return to zero.
OPERATION, CONT. Basic Operation with ID – (No BMI) To Weigh 1. Press ON/OFF key to turn the MV1 on. 2. Press ZERO key to zero weight display. ZERO, GROSS and lb or kg annunciator will turn on to show scale is ready for use. 3. Press ID/HEIGHT key. 4. Display will change to show Id. 5. Using numeric keys, enter up to a 14 digit alphanumeric identification number. 6. Press PRINT/ENTER key. 7. Place patient on scale 8. Read weight display. 9.
OPERATION, CONT. Body Mass Index (BMI) Operation with ID To Weigh and Calculate BMI 1. Press ON/OFF key to turn MV1 on. 2. Press ZERO key to zero weight display. ZERO, GROSS and lb or kg annunciator will turn on to show scale is ready for use. 3. Press ID/HEIGHT key. 4. Display will change to show Id. 5. Using numeric keys, enter up to a 14 digit alphanumeric identification number. 6. Press PRINT/ENTER key. 7.
HEIGHT ROD INSTRUCTIONS Height Rod Hole Location 2in (51mm) Please check the Height Rod hole locations before installing the Height Rod. Some scales may require holes to be drilled. Please follow the measurements for drilling holes if necessary. After holes have been drilled, please follow installation instructions. 9/64” (3.5mm) diameter holes, 1” (25.4mm) from center of column to center of hole 29 47/64” (75.5 cm) IMPORTANT! Measure from bottom of column, not floor or scale base.
HEIGHT ROD INSTRUCTIONS, CONT. 3. Place the large end of the slotted holes in the height rod brackets over the four hex head screws on the back of the column. Height Rod Bracket 4. Pull down to set the screws in the small end of the slotted hole and secure the bracket to the column. 5. Use the included wrench to tighten the hex head screws. Do not over-tighten the screws.
HEIGHT ROD INSTRUCTIONS, CONT. Height Rod Operating Guide 1. Before patient steps onto scale platform, spoon (B) should be rotated to horizontal position, and raised well above patient's apparent height. 2. Patient may now step onto scale platform. Spoon (B) should be held horizontal and above patient's head. A B C E D 3. Carefully lower spoon (B), keeping it horizontal, until it rests gently on top of patient's head. If patient is shorter than 3' 4" (101.
ERROR AND STATUS DISPLAYS Display ERROR ERR OVERFLOW ERR ZERO LIM ERR UNSTAbLE OVER CAPACITY CAL REQUIREd ERR ANALOG ANALOG LOW ANALOG HI ERR EEPROM 10 Meaning General error, invalid keypad entry was attempted. Attempting to display a negative number greater than –9,999 or a positive number greater than 99,999 Indicates an attempt to zero a weight outside scale zero range. Refer to the Calibration Setup ZERO Menu, ZERO LIMIT (Two Percent Zero Tracking Range Limit) parameter.
CARE AND CLEANING OF SCALE Powder Painted Steel While powder painted steel is attractive and so durable that it will last many years longer than ordinary painted steel, it is desirable to clean it thoroughly on a routine basis. There are three basic things that should be remembered when cleaning powder painted steel. 1. Do not use wire brushes, abrasives, or cleaning tools such as steel pads and scrapers, which will scratch the painted surface. Instead, use soft cloths or plastic scouring pads. 2.
PARTS IDENTIFICATION ITEM 1 2 3 4 5 6 20 QTY 1 1 1 2 2 1 1 1 1 1 4 6 6 1 1 2 1 2 1 4 1 1 1 21* 1 7 8 9 10 11 12 13 14 15 16 17 18 19 PART NUMBER MV1 8555-B519-0A 0033-B104-0A 6021-1045 6024-0049 430XG3R800 0033-B315-0A 0033-B254-08 3P2011X 3P8068 3P2087 6021-1423 6024-0047 3P1001X 3P8002X 3P60 2U58 6021-1629 3P8003X 3P8059 0033-D203-0A 0033-D475-0A MV1PWR DESCRIPTION WEIGHT INDICATOR FOR CLINICAL SCALES MEDVUE MTG KIT ASSY TOP PLATE, INDICATOR TO 3P SCW HEX HEAD #10-32 X 1/2 Z/P WASHER LOCK EXT #10 C
PARTS IDENTIFICATION, CONT.
STATEMENT OF LIMITED WARRANTY Detecto Scale warrants its equipment to be free from defects in material and workmanship as follows: Detecto warrants to the original purchaser only that it will repair or replace any part of equipment which is defective in material or workmanship for a period of two (2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect.
STATEMENT OF LIMITED WARRANTY Conditions Which Void Limited Warranty This warranty shall not apply to equipment which: A.) Has been tampered with, defaced, mishandled or has had repairs and modifications not authorized by Detecto. B.) Has had serial number altered, defaced, or removed. C.) Has not been grounded according to Detecto’s recommended procedure. Freight Carrier Damage Claims for equipment damaged in transit must be referred to the freight carrier in accordance with freight carrier regulations.
16 8525-M041-O1 Rev L 8430 Series
