Waist-High Digital Bariatric Scale Model 685X Series Operating Instructions 1930-M458-O1 Rev E 10/14 CARDINAL SCALE MFG. CO. PO BOX 151 WEBB CITY, MO 64870 PH (417) 673-4631 FAX (417) 673-5001 www.detectoscale.com Technical Support: Ph: 866-254-8261 techsupport@cardet.
FCC COMPLIANCE STATEMENT This equipment generates uses and can radiate radio frequency and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
2 6855 / 6855KGEU 6856 / 6856KGEU 6854DHR / 6854KGEUDHR 6857DHR / 6857KGEUDHR 1930-M458-O1 Rev-E Waist-High 685X Series
INTRODUCTION Thank you for purchasing our Waist-High Digital Bariatric Scale. It has been manufactured with quality and reliability at our factory in Webb City, MO USA. Your scale has been tested before leaving our factory to insure accuracy and dependability for years to come. This manual is provided to guide you through the operation of your scale. Please read it thoroughly before attempting to operate your scale and keep it handy for future reference.
UNPACKING INSTRUCTIONS Remove staples or cut along bottom of carton. Lift carton off pallet. Check for any damage incurred in shipping. If scale has been damaged, place a claim with the carrier. It is the responsibility of the purchaser to file all claims for any damages or loss incurred during transit. Use the original carton and shipping material to return the scale. Cut packing straps securing scale to pallet.
OPERATION 6855, 6855KGEU, 6856 or 6856KGEU DO NOT operate the keypad with pointed objects (pencils, pens, etc). Damage to keypad resulting from this practice is NOT covered under warranty. To Weigh 1. Set scale on any hard, level, flat surface or low-cut carpet. 2. Press ON / OFF key to turn on indicator. 3. Press ZERO key to zero weight display. The ZERO and lb or kg annunciator will turn on to show that scale is ready for use. 4. Place patient on scale and read weight display. 5.
OPERATION, CONT. 6854DHR, 6854KGEUDHR, 6857DHR or 6857KGEUDHR DO NOT operate the keypad with pointed objects (pencils, pens, etc). Damage to keypad resulting from this practice is NOT covered under warranty. MedVue Keypad To Weigh 1. Set scale on any hard, level, flat surface or low-cut carpet. 2. Press ON/OFF key to turn the indicator on. 3. Press ZERO key to zero weight display. ZERO, GROSS and lb or kg annunciator will turn on to show that the scale is ready for use. 4.
OPERATION, CONT. 6854DHR, 6854KGEUDHR, 6857DHR or 6857KGEUDHR To Weigh and Calculate BMI Manually Entering Height 1. Press ON/OFF key to turn the indicator on. 2. Press ZERO key to zero weight display. ZERO, GROSS and lb or kg annunciator will turn on to show scale is ready for use. 3. Perform tare operation if required. Refer to Push Button Tare or Tare Weight Entry in previous section for instructions on using tare. 4. Press ID/HEIGHT key. 5.
HEIGHT ROD INSTRUCTIONS Height Rod Hole Location Please check Height Rod hole locations before installing Height Rod. Some models may require holes to be drilled. Please follow the measurements for drilling holes if necessary. After holes have been drilled, please follow installation instructions. Install the two (2) #10 x ½” hex head screws from the hardware pack into the column. 28 IMPORTANT! Measure from top of scale base. 13/16 4 5/16 Height Rod Installation 1.
HEIGHT ROD INSTRUCTIONS, CONT. Height Rod Operating Guide 1. Before patient steps onto scale platform, spoon (B) should be rotated to horizontal position, and raised well above patient's apparent height. 2. Patient may now step onto scale platform. Spoon (B) should be held horizontal and above patient's head. A B C E 3. Carefully lower spoon (B), keeping it horizontal, until it rests gently on top of patient's head. If patient is shorter than 3' 4" (101.
DIGITAL HEIGHT ROD INSTRUCTIONS Digital Height Rod Installation Before starting installation, please unpack carefully and remove all plastic wrappings, foam fillers and cardboard material. You should have the following components: Item Qty 1 1 2 4 3 2 4 8 5 3 Description Detecto Digital Height Rod (DHR) #10x1/2” Hex Head Sheet Metal Screws (bracket to column) Mounting Brackets M4x0.7x5 Pan Head Machine Screws (bracket to height rod) Cable Clip 1.
DIGITAL HEIGHT ROD INSTRUCTIONS, CONT. Measuring Patient’s Height IMPORTANT! Before performing the operations on this page, the digital height rod must be in its “starting position” (inner sliding tube must be down completely inside outer stationary tube and headpiece folded flat against stationary tube) prior to turning on the indicator. Otherwise, the error message 999.9 will be displayed. 1. Make sure height rod is in starting position. 2. Press ON/OFF key to turn indicator on. 3.
PART IDENTIFICATION 6855 Side View Indicator Alternate Mounting Configuration 12 1930-M458-O1 Rev-E Waist-High 685X Series
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION 6856 Side View Indicator Alternate Mounting Configuration 18 1930-M458-O1 Rev-E Waist-High 685X Series
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
STATEMENT OF LIMITED WARRANTY Detecto Scale warrants its equipment to be free from defects in material and workmanship as follows: Detecto warrants to the original purchaser only that it will repair or replace any part of equipment which is defective in material or workmanship for a period of two (2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect.
STATEMENT OF LIMITED WARRANTY Conditions Which Void Limited Warranty This warranty shall not apply to equipment which: A.) Has been tampered with, defaced, mishandled or has had repairs and modifications not authorized by Detecto. B.) Has had serial number altered, defaced, or removed. C.) Has not been grounded according to Detecto’s recommended procedure. Freight Carrier Damage Claims for equipment damaged in transit must be referred to the freight carrier in accordance with freight carrier regulations.
26 1930-M458-O1 Rev-E Waist-High 685X Series
