Specifications

[e-mail] www.motorvac.com
1
060-1600 1 12mm Banjo Fitting CIS Or EFI Systems
060-1602 1 12mm 90 Degree Banjo Fitting CIS Or EFI Systems
060-2402 2 14mm Banjo Fitting Pressure Line
060-3508 1 “Test Port/Schrader Valve” Connection FORD
060-3700 1 “Test Port/Schrader Valve” Connection GM
060-3900 2 5/16” Quick Disconnect - Port Fuel And TBI
060-3901 1 3/8” Quick Disconnect - Port Fuel And TBI
060-4300 1 3/8” TBI And/Or Port Fuel
PART NO. QTY DESCRIPTION
060-1000 2 1/4” Fuel Line - Male - General Application
060-1100 2 5/16” Fuel Line - Male - General Application
060-1200 2 3/8” Fuel Line - Male - General Application
060-1300 2 1/4” Fuel Line - Female - General Application
060-1400 2 5/16” Fuel Line - Female - General Application
060-1500 2 3/8” Fuel Line - Female - General Application
060-1700 1 Carburated Vehicles With 5/16” Flare Fuel Inlets
060-1800 1 Carburated and Early Fuel Injected Vehicles With 3/8” Flare Fuel Inlets
060-2501 1 Forms “Tank to Tank” Loop On All Vehicles
060-2800 1 1/4” Male - Late Model Vehicles TBI And/Or Port Fuel
060-3100 1 TBI And/Or Port Fuel Pressure Line - Male
060-3105 1 TBI And/Or Port Fuel Pressure Line - Female M16 x 1.5
060-3300 1 TBI And/Or Port Fuel return Line - Male M14 x 1.5
060-3305 1 TBI And/Or Port Fuel return Line - Female M14 x 1.5
060-3500 1 3/8” Male Spring Lock With Clip - Port Fuel-Return Line
060-3505 1 3/8” Female Spring Lock - Port Fuel-Return Line
060-3600 1 1/2” Male Spring Lock With Clip
060-3605 1 1/2” Female Spring Lock
060-3901 1 3/8” Quick Disconnect - Port Fuel and TBI
060-4200 1 5/16” Male TBI And/Or Port Fuel
060-4300 1 3/8” TBI And/Or Port Fuel
060-3902 1 1/4” Female TBI And/Or Port Fuel
060-4501 1 Tee Adapter For Single Line Fuel Injection Systems
CARBONCLEAN 245
Specifications
Power Cord 10’ (3 m) Shipping Height 41“ (104 cm)
Power Supply 12 volt DC Shipping Width 24” (61 cm)
New Fluid Capacity 5 Quarts (4.73L) Shipping Depth 19” (48 cm)
CarbonClean 245
Complete Fuel System Service
and Diagnostic Center
RECOMMENDED CHEMICALS MV3 Part No. 400-0020
MV4 Part No. 400-0030
PART NO. 200-8667 ICS KIT (INCLUDED)
PART NO. 200-3025A STANDARD ADAPTERS (INCLUDED)
PART NO. 200-3026A DELUXE ADAPTERS (INCLUDED)
Part No. 500-0245
MotorVac’s two-line cleaning system connects to the engine
using vehicle specific adapters, temporarily replacing the
vehicle’s fuel system. During the first cleaning phase
(with the engine off) the system circulates MotorVac’s
powerful yet safe proprietary cleaning MV3 detergent mixed
with gasoline through the components of the engine’s fuel
system. This phase safely dissolves contaminants, gum
and varnish deposits, capturing them in the unit’s ten micron
filter. The air intake plenum, throttle body and intake
runners are cleaned utilizing the ICS kit in conjunction
with the foaming MV4 detergent. During the second
cleaning phase (engine running), the injector screens,
intake & exhaust valves, top of pistons, combustion chamber,
oxygen sensor, and catalytic converter are cleaned.
This safely dissolves and removes most of the soft carbon
deposits, passing them harmlessly out with the exhaust.
• Fully Electronic-Microprocessor Controlled Operation.
• Vehicle specific, industrial grade adapters/hoses.
• Pressure loss warning light and alarm, automatic shut-off.
• Purge cycle vacuums excess fuel from pressure line
to avoid spills.
• System can run unattended.