co m Release date : 2011.07.14 io ns . Model : QVI-BM09-MAIN-V5.1 IF / Product code : QVI-BM-1107-004 ut Video Interface for BMW C ar -s ol 3/5/6/7 Series www.car-solutions.com V5.1 User Manual support@carsolutions.
co m Contents 1.1 1.2 1.3 1.4 1.5 1.6 Main specification Features System diagram Components Exterior POWER cable 2. Setup ol ut DIP switch Setup for car model & navigation Factory mode Original buttons usage Remote controller usage Keypad usage Setup for rear camera OSD (on screen display) 3. Installation -s 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 io ns . 1. Before installation C ar 3.1 Installation diagram 3.2 Cautions on installation 3.3 Installation 4. Troubleshooting www.car-solutions.
co m 1.1 Main specification 1. Compatibility Most of brand-new cars coming with CIC Navigation Computer System including BMW 3,5,6,7,Xseries io ns . 2. Product composition Multimedia Interface (made for specific models) * 1ea Most TV-Free (displaying original DVD and navigation) – optional 4. MULTIMEDIA INTERFACE output spec. 1 * LCD output ut 3. MULTIMEDIA INTERFACE input spec.
800 x RGB x 480 24bit wide display of high definition co m 1.2 Features LED backlight device (600cd) – able to adjust brightness io ns . Stereo sound support via headphone input ZOOM Function ( 16:9 -> 4:3 ) Able to connect external video/audio device C ar -s ol ut Able to display original images at once ( Normal -> Zoom1 -> Zoom2 -> Zoom3 ) www.car-solutions.
Switch for source toggle Keypad co m 1.3 System diagram NAVIGATION Input (Analog RGB) io ns . OEM Button (Can Intrface) MCU DISPLAY A/V 1 VIDEO MUX A/V 2 ut VIDEO CIRCUIT Car Installation OEM LCD A/V 3 Car Screen Input POWER CIRCUIT A/V OUT HEADREST MONITOR C ar (CAR MAIN BOARD) -s ol CVBS (Rear camera) Power Input (+8VDC ~ +18VDC) www.car-solutions.
Mode cable * 1EA LCD cable * 1EA Remote control * 1ea A/V cable * 1EA ar -s ol ut io ns . IR cable * 1EA co m 1.4 Components C Modified POWER cable (7P) * 1EA www.car-solutions.
⑨⑧ ⑦ ⑥ ⑤ Dimension Horizontal length 164.4mm Vertical length 94.4mm Height 28.2mm io ns . ⑩ co m 1.5 Exterior ① POWER ② RGB(IN) ol ut ③ REAR CAMERA POWER ⑤ LCD-OUT ⑥ LCD-IN ⑦ IR -s ar C www.car-solutions.
io ns . co m 1.6 POWER cable This has to be connected to the spot located at the back of the monitor which the original power & CAN cable originally connected. ol -s ar C Approximately 15cm ut NOISE FILTER BOX www.car-solutions.com Noise filter box The original power& CAN cable has to be connected to this part.
PIN Function Dip S/W Selection 1 Displaying RGB input ON : displaying RGB mode OFF : hiding RGB mode Displaying A/V 1 3 Displaying A/V 2 ON : displaying A/V 2 OFF : hiding A/V2 4 Displaying A/V 3 ON : displaying A/V 3 OFF : hiding A/V3 5 Setup of monitor size ※ ON : DOWN / OFF : UP default : ON (DIP #8) ※ DIP S/W usage example - Input Mode : A/V2, A/V3 - Original Navigation - External rear camera ut io ns . 2 ON : displaying A/V 1 OFF : hiding A/V1 co m 2.
2.2 Setup for car model & navigation Setup for navigation io ns . Setup for car model co m FACTORY mode – Press ◀ button 2 seconds long on the remote controller.
2.3.1 FACTORY mode ut io ns . co m FACTORY mode – Press ◀ button 2 seconds long on the remote controller.
2.3.2 FACTORY mode ut I_DRV/ I_DRV CONTROL Selecting whether to use I_DRV function or not ar -s ON / OFF C ML 740T ARION PANASONIC HSD100 COMTEC NET770 PIONEER ML100 ol I_DRV - I_DRV REMOTE Selecting model of navigation and DMB respectively to control I_DRV function io ns . co m FACTORY mode – Press ◀ button 2 seconds long on the remote controller. •Selecting NAVIGATION model : in RGB mode •Selecting DVD model : in A/V mode www.car-solutions.
I-Drive buttons (whole model) Mode Whole mode Key MENU co m 2.
Key Function POWER & PIP Activating OSD menu io ns . MENU Unavailable co m 2.5 Remote controller usage Making a selection, changing image display ▲ Moving upward (If you press this button 2 seconds long, “Hot key” function will activate/ deactivate.) ▼ Moving downward ◀ Moving leftward (If you press this button 2 seconds long, you can get access to the factory mode.) ▶ Moving rightward (If you press this button 2 seconds long, you can reset all the data about user environment.
2.6 Keypad usage io ns . co m Select one between the remote controller and the keypad FACTORY MODE (Interface setting) : Press these buttons on OSD keypad in the following sequence; UP→DOWN→UP →MENU Function ut Key Activating OSD menu and Getting back to the previous state after setting mode SEL/INPUT Making a selection and hanging modes -s Moving rightward or downward (IF you press this button 2 seconds long, you can reset all data.
2.7.1 Setup for rear view camera PARK SETUP : Adjusting the position of the parking guide line (available in PARK SETUP -> V-POSITION, H-POSITION) ol LAMP : Detecting the rear view camera via rear lamp (Installer must connect “Rear-C” cable of the power cable to the rear lamp of the car.) PARK PARK ENABLE : Selecting whether to display the parking guide line or not on rear gear (default : ON) ut UTIL - REAR SELECT Selecting how to detect the rear view camera io ns .
Setup for displaying rear view co m 2.7.2 Setup for rear view camera Positioning transparent PDC image Press series5 : Press button on the steering wheel and select one from 4 options as shown below. button about 2 seconds and select one among position of PDC image among 3 options as shown below. • The types of PIP function in rear view mode can differ io ns . series7 : Press long on I-Drive 4 options. button on the steering wheel and select a from along car models.
co m 2.8.1 OSD (on screen display) ut io ns .
2.8.2 OSD (on screen display) io ns . co m Video mode OSD UTIL LANGUAGE : Choosing interface language while changing mode between A/V and DVD TRANS : Adjusting transparency of OSD H_POSITION, V_POSITION : Positioning OSD menu FACTORY RESET : Resetting all the data about the relevant mode (applicable to navigation, A/V, DMB, rear mode respectively) -s IMAGE ol ut DMB mode (only for domestic use) C ar BRIGHTNESS CONTRAST SHARPNESS USER IMAGE : Selecting one among 4 color options www.
co m 3.1 Installation diagram Connecting this to the spot which the original POWER & CAN cable was connected. Original Monitor Connecting the original POWER & CAN cable to this part. Original LCD cable io ns . Offered LCD cable ar C Audio R Audio L Video NAVI DVD GND (black) SYNC (white) B DATA (blue) G DATA (green) R DATA (red) ACC GND CAN CAN www.car-solutions.
co m 3.2 Cautions on installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be separated when connecting interface. Should be no any electronic devices or magnetic pole around installation place. All steps of installation should be done by well-trained specialist. Dismantling without manufacturer’s permission can not be guaranteed, (No permission to break attached label on the board.
co m 3.3 Installation 3.3.1 Connecting the monitor with the interface ut io ns . ① Connect LCD cable enclosed in our package to the spot that the original one is connected after disconnecting the original LCD cable from the monitor as shown left. C ar -s ol ② Connect the original LCD cable to “LCD-IN” socket of the interface. www.car-solutions.
io ns . 3.3.3 Connecting CAN cable respectively co m 3.3 Installation -s ol ut CAN-High CAN-Low POWER CABLE C ar Connect CAN-H cable (green+brown) enclosed in our package with the original CAN-H cable (green+orange). And connect CAN-L cable (green) enclosed in our package with the original CAN-L cable (green). www.car-solutions.
co m 4. Troubleshooting Q. I can not switch A/V sources A. Check IR or Ground cable connection. Check LED lamps in the interface, if it is not on, check power cable. Q. All I got on the screen is black. A. Check second LED lamp of the interface is on, if not, check A/V sources connected are working well. (Second lamp indicates AV sources connected works well.) Check interface connection has been done well. io ns . Q. Displayed image color is not proper (too dim or not suitable color) A.
