ns tio Release date : 2011.08.08 Model : QVL-A4L-V7.3 / Product code : A4L-1106-003 So lu Video Interface for AUDI A4, A5, Q5 C ar without MMI panel With external touch screen panel support Installation Manual www.car-solutions.com support@carsolutions.com.
Contents 1. Before Installation tio ns 1.1 Main Specifications 1.2 Features 1.3 System diagram 1.4 Package content 1.5 Exterior 3. Installation C ar So 2.1 DIP switches 2.2 Remote controller 2.3 OSD buttons activation 2.4 OSD (On Screen Display) 2.5 FACTORY mode 2.6 Parking guidelines setting 2.7 Touch screen panel calibration 2.8 Remote controller buttons 2.10 DVD, DVB-T (CMMB) model selection lu 2. Setup 3.1 Installation diagram 3.2 Cautions on installation 3.3 Installation 4.
1.1 Main Specifications tio ns 1. Inputs - 1 x Analog RGBCs (for navigation system) - 1 x REAR-C Input (for external rear camera source, supports NTSC & PAL auto detection ) - 3 x A/V Input (for external video source - DVD, TV, DVB-T; supports NTSC & PAL auto detection ) - 1 x LCD-IN (video input from OEM video unit) - 1 x TOUCH – on sub-board (for external touch screen panel) So lu 2.
1.2 Features ns - DVD, NAVI control by touch screen panel, OSD-buttons (optional) tio - Installation near OEM display lu - More convenient installation via sub-board So - Plug & Play installation by LVDS cable - Possibility to adjust position of AV1-3, RGB image C ar - Remote controller offered - Improved On Screen Display menu www.car-solutions.
1.3 System Diagram ns TOUCH SCREEN CONTROLLER lu NAVIGATION LCD INPUT\OUTPUT So RGB input for Navigation unit REAR-C (external reverse camera input) VIDEO CIRCUIT C ar A/V3 Input OEM LCD LVDS SUB BOARD Video Interface A/V1 Input A/V2 Input MCU OEM VIDEO UNIT tio DVD IR DVB-T IR MODE Button DIP Switches Remote controller POWER CIRCUIT External Touch Screen Panel VIDEO MUX Headrest Monitors Power Input (+10 V DC~+16 V DC) www.car-solutions.
TOUCH OUT cable * 1pc. LCD cable * 1pc. tio IR cable (4P) * 1pc. ns 1.4 Package Content TOUCH cable * 1pc. C ar RGB cable * 1pc. So MODE button * 1pc. lu LVDS cable * 1pc. Rear view camera power cable * 1pc. POWER cable (24P) * 1pc. www.car-solutions.com AV cable * 1pc. Remote controller * 1pc.
1.5 Exterior ⑦ ⑥ ⑤ ④ - SUB-BOARD Dimensions ns (52 mm *31 mm *19 mm) ⑪ lu tio Horizontal length 125 mm Vertical length 102 mm Height 24 mm ① POWER/CAN/RGB So ② AV inputs/outputs ③ Rear camera power output C ar ④ LVDS output ① ② ③ www.car-solutions.
2.
Function POWER & PIP NOT USED Selection or Mode change So OK OSD Menu lu MENU tio Buttons ns 2.2 Remote Controller Move UP C ar Move DOWN Move LEFT (or press 2 sec. – Factory Mode) Move RIGHT (or press 2 sec. - Factory Reset) www.car-solutions.
2.3 OSD Buttons Activation OSD buttons for DVD For DVD control via OSD menu installer shall connect DVD system to AV1 input and join “DVD IR” cable from video interface cables with DVD IR receiver DATA cable. tio ns First of all, if you touch the screen in mode ”AV1”, you can see the menu as shown left. And then if you do NOT touch anything on the screen for 5 seconds or longer; or if you touch the screen in the place beyond menu, the menu will disappear.
2.4 OSD (On Screen Display) OSD menu: Press ”MENU” button on the remote controller. Analog RGB mode Video AV1-3 mode Video AV1-3 mode Analog RGB mode Video AV1-3 mode IMAGE C ar So lu tio ns Analog RGB mode - BRIGHTNESS - CONTRAST - SATURATION - HUE - SHARPNESS - USER IMAGE : To choose a option among 4 prepared color shades. www.car-solutions.
2.5 Factory Mode ns FACTORY mode – Press ◀ buttons on the remote controller for 2 seconds.
2.6 Parking Guideline setting FACTORY mode – Press ◀ buttons on the remote controller for 2 seconds. tio ns ① Set “ON” in “PARK ENABLE” line in the PARK section as shown left. (default – OFF) C ar So lu ② If you turn on rear gear after setup, parking guidelines will appear on screen as shown left. Now if you push “OK” button, you can see “H-POS” on the left of screen. Then adjust horizontal position of the parking guidelines.
2.7 Touch Screen Panel Calibration C ar So lu tio ns If you use external touch screen panel for connected DVD player, TV tuner, DVB-T receiver control by OSD buttons, which will emulate remote controller buttons of these devices, you should calibrate the connected touch screen panel. ① First of all, press ◀ button on remote controller for 2 seconds. Then you can enter the FACTORY mode. ② Set “YES” after CALIBRATION option is selected as shown above. www.car-solutions.
2.8.1 Remote Controller Buttons Programming OSD buttons value using remote controller supplied together with DVD,TV,DVB-T. So lu tio ns If you want to control DVD and DMB models other than SANYO and NECVOX via touch screen (using OSD buttons, you can program value of DVD and DMB’ s remote controller which you have. Then you can control DVD and DMB via touch screen. C ar ① First of all, press ◀ button on remote controller for 2 seconds. Enter FACTORY mode, then select IR MEMORY in UTIL section.
So lu tio ns 2.8.2 Remote Controller Buttons C ar Programming Instructions > continued… c. Programmed values will appear as green text in the marked area on pressing the button. And the values will be saved automatically. d. Program other buttons value in OSD menu according to the above-mentioned procedure www.car-solutions.com ③ After programming select “INPUT” in OSD menu and press “OK”. Then you can see confirmation window as shown above. If you choose “YES”, all entered values will be saved.
2.9 DVD, CMMB Model Selection ns Factory Default : DVD TYPE - NECVOX/SANYO (For Chinese DVD) DMB TYPE – CMMB (For Chinese DMB) CMMB TYPE C ar UTIL – DVD/DMB TYPE So lu tio DVD TYPE If DVD/CMMB type that you want to use is not NECVOX or SANYO, you have to register values of the remote controller that you want to use in the “IR MEMORY” section and set the “DVD TYPE”/”CMMB TYPE” to “USER”.
3.1 Installation Diagram Touch panel not included! NOT INCLUDED IN PACKAGE! TOUCH LCD-OUT So LCD-IN TOUCH C ar Control Box Original LCD cable CVBS REAR CAMERA REAR CAM POWER Audio R Audio L Video www.car-solutions.com PB12 (N.C) GPIO-ZO : MMI GND ACC AV/OUT AV3 AV2 AV1 REAR C IR CAN-L CAN-H IR-AV3 (DTV) IR-AV2 (DVD) IR-AV1 (NAVI) PARKING (SAFE) Offered Touch cable REAR OPT2 (N.
3.2 Cautions on Installation Ignition key should be taken off before starting installation, interface power connection must be the last step in installation. Power cable should be disconnected during interface installation. There should be no electronic devices or magnetic pole around the installation place. All steps of installation should be done by well-trained specialist.
Disconnect OEM cable from display and connect it to LCD-IN socket on sub-board. Be careful while OEM cable connection to sub-board, follow graphic prompts inside the socket! C ar So lu tio ns 3.3 Installation www.car-solutions.com Connect the provided LCD-OUT cable to rear side of LCD monitor and to socket on the sub-board as shown left.
Connect touch screen cable (included in the package) to external touch screen panel flat cable and Touch socket of the sub-board. C ar So lu tio ns 3.3 Installation Connect LVDS cable (included in the package) to sub-board and video interface main module. www.car-solutions.
C ar So lu tio ns 3.3 Installation www.car-solutions.com Connect TOUCH OUT cable (included in the package) to “TOUCH” socket of the video interface. Then connect the opposite end of the cable to navigation unit touch cable or USB touch screen controller (USB touch screen controller is not included in the package).
4. Troubleshooting ns Q. I can not switch A/V sources. A. Check IR or Ground cable, and MODE button connection. Check LED lamps in the interface, if they are not on, check power cable. tio Q. All I got on the screen is black. A. Check whether interface second LED lamp is on. If not, check whether connected A/V sources operate well. (Second lamp indicates that connected AV sources are working well.) Check interface connection. So Q. Rear camera image does NOT appear. A.
