Andover Continuum Product Catalogue ™ Issue: October 2008 UK / EMEA / ASIA PACIFIC Make the most of your energy
Table of Contents About TAC........................................................................................................................................ About TAC-1 System Overview................................................................................................................System Overview-1 Software................................................................................................................................................. Software-1 Foreword . ...............
BACnet Controllers (continued) Terminal Controllers b3850 Series...............................................................................................................................................BACnet-7 b3865-V/b3866-V.....................................................................................................................................BACnet-8 b3867......................................................................................................................................
About TAC Open Integrated Systems for Building IT™
Global Leader in Building IT TAC is a leading provider of building automation solutions based on Open Integrated Systems for Building IT. TAC’s mission is to provide added value through building environment services for indoor climate, security and use of energy, delivered with advanced technology to end users and property owners throughout the world.
THE ADVANTAGES OF OPEN INTEGRATED SYSTEMS FOR BUILDING IT Our open, standard technology enables you to integrate heating and cooling, access control, security monitoring, ventilation, fire and smoke control and lighting, across your enterprise. This approach reduces training and maintenance costs, increases energy savings, and adds value by collecting and sharing vast amounts of pertinent facility and financial data, which helps you run a more profitable building.
Notes
System Overview Integrated Solutions Enabled by Open Systems for Building IT®
Andover Continuum System Architecture Expect More from Building Automation and Security Systems Today’s buildings demand more from building automation and security systems. Buildings must adapt to many rapid changes, and be smarter, more comfortable, more efficient and safer than facilities designed just a few years ago. The controls system is the critical component in meeting these new demands, and the Andover Continuum system from TAC is ready for today’s needs, while helping prepare for the future.
Open and Integrated Solutions A Track Record of Innovation Andover Continuum was the first to integrate HVAC and Electronic Access Control into one controller, and the first to offer controllers with onboard Ethernet communications and an embedded web server. It was also the first system to integrate access control and digital video recording, and the first native BACnetTM system to also handle full security management tasks.
Andover Continuum Delivers More INTERFACES FOR ALL USERS From the facility manager and building owner, to the department manager or receptionist, a diverse group of people need to access the system for a variety of functions, using a wide range of user interfaces: • Fixed workstations – PCs, laptops • Web browsers – PCs, laptops, PDAs, mobile phones • Service tools – laptops, PDAs • Wall displays – touch screens, keypads with displays user interACTION • View a graphic • View and acknowledge alarms •
Software Photo by Kevin Hester COURTESY OF THE DENVER ART MUSEUM
Andover Continuum Continuum CyberStation Single & Multi-User The Andover Continuum CyberStation™ workstation software is a Microsoft® Windows®based, colour graphic user interface. Continuum’s software provides powerful features and timesaving tools to control and monitor your Andover Continuum intelligent building system over a high-speed Ethernet LAN/WAN or single-user network. Single-User The Single User (SU) version consists of a PC running Windows Workstation.
Andover Continuum Continuum CyberStation Single User & LAN Workstation Continuum Single User Software (includes MSDE database) 1000 I/O Points HVAC Programmer’s Edition SU-HV-P-USB 1000 I/O Points (5,000 Personnel Records for Security) Security Programmer’s Edition SU-SEC-P-USB 1000 I/O Points (5,000 Personnel Records for Security) Integrated Programmer’s Edition SU-INT-P-USB Unlimited I/O Points (4 Million Points) HVAC Programmer’s Edition SU-HV-U-P-USB Unlimited I/O Points (4 Million Personnel Re
Andover Continuum Continuum CyberStation web.Client web.Client™ TAC’s web.Client™ software allows authorised users to access their Continuum building management system from any PC on the network or over the Internet via a web browser. It provides major benefits for integrated facility management systems.
Andover Continuum Continuum CyberStation CFR Compliance Pack CFR Compliance Pack The Continuum CFR Compliance Pack software product range enhances the Andover Continuum system to provide FDA-regulated businesses with the information they need to achieve regulatory compliance for their facilities. Using 21 CFR Part 11 electronic record and signature standards, CFR Compliance Pack maintains a complete archive of all events and parameters related to the environmental and security conditions of a facility.
Andover Continuum Continuum CyberStation Add-on Reporting Modules Add-On Reporting Modules for Continuum Built on top of Continuum CyberStation’s already powerful, flexible and easy-to-use standard reporting modules are a growing list of options to further increase the productivity and efficiency in managing facilities. Each reporting option can easily be added to existing installations by purchasing a licence code to enable the specific module.
Andover Continuum Continuum CyberStation Add-on Reporting Modules Alarms Plus Provides the following timesaving capabilities: • Save report configuaration settings for future recall • Manually and automatically e-mail an alarm report to a list of recipients • Automatically e-mail an alarm report to a list of recipients • Automatic printing of alarm reports • Automatic saving of alarm reports to file Alarms Plus AL-PLUS Alarms - Categories Provides quick sorting and reporting of alarms and alarm category
Andover Continuum Continuum CyberStation Add-on Reporting Modules Remote Reports Provides the ability to run the six standard Continuum reports on non-CyberStation workstations. Note: No Continuum security is supported for this feature, and network connectivity to the Continuum file server is required. Remote Reports REPORTS-R Time Tracker Provides basic time totalisation of hours worked, based on card access events in the Continuum system database.
Andover Continuum Continuum CyberStation RoamIO2 Service Tool Continuum RoamIO2 Service Tool The RoamIO2 Service Tool is a compact hardware adapter with software applications, that allows you to quickly connect to any Andover Continuum system using a Pocket PC or laptop. Designed to clip onto a technician’s belt, this tool gives you the freedom of mobility through a local connection to a field bus or Ethernet network.
Notes
Infinet Controllers
Andover Continuum Infinet Infinet Controllers Introduction Andover Continuum Infinet Family of Controllers Andover Continuum is a full system of controllers and user interface software products that can be combined in many different ways to customise the system to site requirements. Whether the site is a single building or across multiple locations, Andover Continuum is scalable and adaptable. It can even be tailored for specialised environments.
Andover Continuum Controller/Router Series bCX1 Series Infinet The Continuum bCX1 is a feature-rich, yet cost-effective network controller that supports the Infinet family of field controllers. The controller provides a full function 10/100 Ethernet connection and support for up to 127 Infinet field controllers, with a second communication port available for a modem connection or a Plain English™ driver.
Andover Continuum NetControllers I & II Power Supply Units Infinet TAC provides high performance network management with the Continuum family of CX programmable network controllers. NetControllers use LON® technology I/O Modules, while Continuum’s Infinet field controllers provide stand-alone direct digital control of your building services.
Andover Continuum Network Master Controller NetController II Infinet NetController II CPU Module The Andover Continuum NetController II is a redesigned version of the NetController, a highpowered Central Processing Unit (CPU) module and network manager for the Andover Continuum intelligent building system.
Andover Continuum Infinet Network Master Controller CX9900 NetController-CPU Continuum CX9900 Central Processing Unit (CPU) The Continuum CX9900 CPU provides monitoring and control of both Continuum I/O modules and Infinet distributed controllers. Flash memory allows easy on-line software upgrades and is freely programmable using Plain English programming. The CX9900 connects the high speed Ethernet network to local networks. Quick release fasteners enable DIN rail mounting without the need for tools.
Andover Continuum NetControllers I & II I/O Modules Infinet Continuum Input / Output Modules The Continuum I/O modules feature a sleek, lightweight casing and a 3-position front cover for easy, hands-free access. Built-in quick-release fasteners at the back of each I/O module are provided for DIN rail mounting, no tools required. These fasteners snap into a locked position for panel mounting.
Andover Continuum Infinet NetControllers I & II I/O Modules DO-6-TR Output Module 6 digital outputs, Form A optically isolated triacs (0.5A, 24VAC). PWM control of 0.1 seconds. Combine 2 outputs into 1 tri-state. Power requirements are 24VDC, 1.1 watts. Minimum current required for correct switching is 30mA. No DC loads. Output Module DO-6-TR AC-1 Input/Output Module Full I/O for one door or portal. 1 reader/keypad input, handling either combo reader/keypad units or separate units.
Andover Continuum NetControllers I & II Display Modules Infinet Infistat Display Interface The Infistat Display Module is a convenient, programmable interface for your facility management system. Provides authorised operators quick and easy access to HVAC or security information, and/or enables them to adjust personal comfort levels with little or no training. The Infistat can co-exist with other Continuum I/O modules, such as the UI-8-10, DI-8, AO-4-8, etc. (up to 32 modules per single NetController).
Andover Continuum Infinet Network Master Controllers ACX5720/5740 ACX Series for Ethernet The ACX Series controllers for Ethernet are the most powerfull all-in-one access controllers available for the Andover Continuum product line. The controllers are designed from the ground up to handle the latest U.S. government security requirements. Additionally, the ACX Series is just as attractive for one as it is for eight door installations.
Andover Continuum Network Master Controller XXXXXX XXXXXXX XXXXXXCX9702 XXXXXXAccessController Infinet CX9702 AccessController Designed for small, unmanned, or remote sites, the CX9702 AccessController provides networked, electronic access control, temperature control, and alarm monitoring in a single, costeffective controller.
Andover Continuum Infinet System Controller i2920 i2 Family of Controllers TAC continues to provide powerful, state-of-the-art controllers to keep up with tomorrow’s fast paced world. Introducing the Infinet II (i2) family of controllers – ready to meet your most challenging control applications. The i2 controllers come packed with exciting new features to make your control projects easier.
Andover Continuum Local Controllers i2600 Series & i2800 Series Infinet i2600 Series and i2800 Series Local Controllers The Infinet II (i2) 600 and 800 are stand-alone, freely programmable (using Plain English language), microprocessor-based local controllers for DDC control, capable of monitoring, controlling, scheduling and logging modular systems. Up to 254 controllers can be networked on one CX master using Continuum’s true peer-to-peer Infinet network.
Andover Continuum Infinet Local Controllers i2810 i2810 Series Local Controllers The Infinet II (i2) 810 is a stand-alone, freely programmable (using Plain English language), microprocessor-based local controller for DDC control. Capable of monitoring, controlling, scheduling and logging modular systems.
Andover Continuum Terminal Controller i2850 Series Infinet i2850 Series Terminal Controllers Infinet II (i2) 850 series terminal controllers are stand-alone, freely programmable (using Plain English language), microprocessor based controllers used for cost-effective DDC control of individual terminal units. Capable of monitoring, controlling, scheduling and logging modular systems. Up to 254 controllers can be networked on one CX master using Continuum’s true peer-to-peer Infinet network.
Andover Continuum Infinet Terminal Controllers i2865-V/866-V i2865-V/i2866-V VAV Controller The Infinet II (i2) 865-V and 866-V are unique, low cost VAV box controllers that come equipped with a built-in damper actuator to streamline hardware installation and reduce commissioning time. Freely programmable using Plain English language, these stand-alone controllers are capable of monitoring, controlling, scheduling and logging modular systems. Service and Smart Sensor ports are provided.
Andover Continuum Terminal Controller i2867 Infinet i2867 Terminal Controller The Infinet II (i2) 867 is a compact terminal controller providing low cost DDC control of package units, fan coil units, heat pumps and small AHU’s that require both digital and analogue outputs. Freely programmable using Plain English language, the unit is provided with a service port and an input for a Smart Sensor, TAC’s low cost programmable user interface.
Andover Continuum Terminal Controller i2885-V Infinet i2885-V VAV Controller The Infinet II (i2) 885-V is a unique low cost VAV box controller complete with a built-in actuator to simplify hardware installation and reduce commissioning time. Freely programmable using Plain English language, this stand-alone controller is capable of alarming, scheduling and logging modular systems. Up to 254 controllers can be networked on one CX master using Continuum’s true peer-to-peer Infinet network.
Andover Continuum Terminal Controllers i2887 Infinet i2887 Series Terminal Controllers The Infinet II (i2) 887 is a fully programmable, low cost, general purpose terminal controller. It has all the power of an Infinet II controller, but with a small form factor. With its unique mix of three universal inputs, one Smart Sensor/room sensor input, four triac outputs and one relay output, the i2887 can be easily configured to control Heat Pumps, Fan Coils, or AC units.
Andover Continuum Infinet Expansion Modules i2 Expansion Modules i2 xP Expansion I/O Modules The Infinet II (i2) “plug-in” expansion modules provide a convenient, low-cost, and flexible means to add additional input and output points to Continuum’s distributed application controllers. Up to two modules (max.) plus a remote mounted (3m max.) display module can be powered directly from any Infinet Controller, maximum 180mA of power available.
Andover Continuum Wireless Infinet Field Bus Infinet Product Overview Andover Continuum is the first system to offer a full range Wireless Field Bus solution. Wireless technologies can be found in all the corners of the globe from mobile phones to wireless hotspots in airports, where travelers can browse the Internet. As a result, wireless has lowered installation costs while providing a level of connectivity freedom never before seen.
Andover Continuum Wireless Infinet Field Bus Infinet Simple Power Connections The adapter is powered directly from the 3.3V power feeds of the controller’s service port. Power kits are available to run the adapter as a repeater to bridge controllers that are far apart. Adding the Wireless Adapter is a snap. A maximum of 32 wireless nodes are supported per controller.
BACnet Controllers
Andover Continuum BACnet Controllers Introduction BACnet Andover Continuum BACnet Family of Controllers BACnet that is Intelligent . . . At Every Level Open standards provide building owners with flexibility and choice when selecting building automation technology. The BACnet open standard provides a universal model for creating building automation systems that can interoperate with one another.
Andover Continuum BACnet Controller / Router bCX1 Series BACnet The Andover Continuum bCX1 Series is a series of Native BACnet routers and controller/routers, which head up the BACnet family of Continuum controllers. These controllers reside at the network level and route BACnet messages between BACnet/IP, BACnet over Ethernet, and MS/ TP networks. They can also serve as BACnet Broadcast Management Devices (BBMD), allowing for routing of messages between IP networks.
Andover Continuum BACnet System Controller b3920 Compliance with ASHRAE 135-2004 (protocol revision 4) The Andover Continuum system is up-to-date with the latest advances in the ASHRAE BACnet standard. BACnet is in its 4th protocol revision since its introduction in 1995. The ASHRAE 1352004 BACnet standard calls for BACnet vendors to update their BACnet controller to account for Scheduling and Trending improvements as well as other background communications.
Andover Continuum Local Controllers b3600 Series & b3800 Series BACnet b3600 Series and b3800 Series Local Controllers The BACnet b3600 and b3800 are stand-alone microprocessor-based local controllers for DDC control capable of monitoring, controlling, scheduling and logging modular systems. Up to 127 controllers can be networked on one bCX1 controller.
Andover Continuum BACnet Local Controllers b3810 b3810 Series Local Controllers The BACnet b3810 Series are stand-alone microprocessor-based local controllers for DDC control, capable of monitoring, controlling, scheduling and logging modular systems. The b3810 offers the same features as the b3800, plus an I/O expansion port, built-in overrides for manual control of each output and an optional display with keypad for local information control (to be connected to an I/O expansion port).
Andover Continuum Terminal Controller b3850 Series BACnet b3850 Series Terminal Controllers BACnet b3850 Series terminal controllers are stand-alone microprocessor-based controllers used for cost-effective DDC control of individual terminal units. They are capable of monitoring, controlling, scheduling and logging modular systems. Up to 127 controllers can be networked on one bCX1 controller.
Andover Continuum BACnet Terminal Controllers b3865/866-V b3865-V/b3866-V Controller The BACnet b3865-V and b3866-V are unique, low cost VAV box controllers that come equipped with a built-in damper actuator to streamline hardware installation and reduce commissioning time. These stand-alone controllers are capable of monitoring, controlling, scheduling and logging modular systems. Service and Smart Sensor ports are provided. Up to 127 controllers can be networked on one bCX1 controller.
Andover Continuum Terminal Controller b3867 BACnet b3867 Terminal Controller The BACnet b3867 is a compact terminal controller providing low cost DDC controls of package units, fan coil units, heat pumps and small AHU’s that require both digital and analogue outputs. The unit is provided with a service port and an input for a Smart Sensor, TAC’s low cost programmable user interface. Up to 127 b3867 controllers can be networked on one bCX1 controller.
Andover Continuum BACnet Terminal Controller b3885-V b3885-V VAV Controller The b3885-V is a unique low cost VAV box controller complete with a built-in actuator to simplify hardware installation and reduce commissioning time. This stand-alone controller is capable of alarming, scheduling and logging modular systems. Up to 127 controllers can be networked on one bCX1 controller.
Andover Continuum Terminal Controllers b3887 BACnet b3887 Series Terminal Controllers The BACnet b3887 is a fully programmable, low cost, general purpose terminal controller. With its unique mix of three universal inputs, one Smart Sensor/room sensor input, four triac outputs and one relay output, the b3887 can be easily configured to control Heat Pumps, Fan Coils, or AC units.
Andover Continuum BACnet Expansion Modules b3 xP b3 xP Expansion I/O Modules The BACnet (b3) “plug-in” expansion modules provide a convenient, low cost, and flexible means to add additional input and output points to Continuum’s distributed application controllers. Up to two modules (max.) plus a remote mounted (3m max.) display module can be powered directly from any BACnet Controller, maximum 180mA of power available. An external power supply can NOT be used to add additional modules.
Andover Continuum BACnet Wireless BACnet Field Bus Product Overview Andover Continuum is the first BACnet system to offer a Wireless BACnet Field Bus solution. Wireless technologies can be found in all the corners of the globe from mobile phones to wireless hotspots in airports, where travelers can browse the Internet. As a result, wireless has lowered installation costs while providing a level of connectivity freedom never before seen.
Andover Continuum BACnet Wireless BACnet Field Bus Amplified Output The Wireless Adapters/Repeaters have an amplified output to their onboard antenna, with a maximum of +6dBm power to the antenna and a maximum radiated power output of +10dBm. The TAC Wireless Adapters/Repeaters are capable of delivering the strongest output permitted by FCC and CE regulations.
Network & Communications
Andover Continuum i2 Infilink Network Drivers i2 Infilink 200 The i2 Infilink 200 is an electronic repeater and 5 port active hub in one device. Each RS485 output has the drive capability of up to 1200m or 31 separate devices. The Infinet field bus system can accommodate both Infinet and Infinet II controllers.
Andover Continuum BACnet Network Drivers b-Link (Copper) The b-Link electronic repeaters are multi-port active hubs for the BACnet MS/TP field bus, designed to transmit RS-485 signals beyond the 4000-foot (1.2 km) limitation. • 1 x RS-485 input • 4 x RS-485 outputs • 1 x RS-232 output for short haul modems • LED indication on all ports for troubleshooting • AC and DC versions available • CE approved Power: Operating Range: Dimensions: 115/230VAC (switch selectable) @ 2.
Andover Continuum OPC Server Controller OPC Server The TAC OPC Server allows third party OPC-based client applications to access data in the Continuum and Infinity controllers through an Ethernet network. OPC, an industry-standard protocol, provides seamless open communciations between different manufacturers’ devices and databases.
Andover Continuum Third Party Interfaces Third Party Communications Interfaces and Protocols TAC meets today’s need for open systems and total integrated building control with industrystandard interfaces, such as BACnet and OPC, plus a wide range of third party communications interfaces called drivers.
Andover Continuum Third Party Interfaces standard protocols Besides the custom point-to-point interfaces listed, Andover Continuum also offers many standard interfaces designed to facilitate interoperability among many different devices. These standard protocols include BACnet, LON, Modbus, and an OPC Server package. Equipment* Descrip.
Andover Continuum Third Party Interfaces battery monitoring systems Manufacturer Equipment* Descrip./ Model Newport Data Systems Cell Watch Battery Monitoring Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible X E01-0210-175 3 3 2nd Generation Continuum Compatible Driver Description Full voltage, current and internal resistance Systems Battery Monitoring. Monitoring of battery cells, through a network of Control Units and Data Collection Modules.
Andover Continuum Third Party Interfaces fire systems Manufacturer Equipment* Descrip./ Model Driver Type TAC File Reference Number* ActionAir LNS System X E01-0210-238 Clymac Ziton Fire Panel X E01-0210-223 X E01-0210-231 Cerberus Infinity Compatible 1st Generation Continuum Compatible 2nd Generation Continuum Compatible 3 3 Driver Description The Actionair LNS System consists of a Panel PC, UPS and pre-loaded software.
Andover Continuum Third Party Interfaces fume hood controls Manufacturer Equipment* Descrip./Model Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible Phoenix Controls Celeris system X E01-0210-197 3 3 Uses BACnet-over-Ethernet to communicate to a Celeris system through a Phoenix Accel-Way. Read/Write. Tek Air FVC-2000 X E01-0210-140 3 3 Allows monitoring & control of Laboratory Fume hoods.
Andover Continuum Third Party Interfaces package environmental units Manufacturer Liebert Equipment* Descrip./Model SiteLink Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible 2nd Generation Continuum Compatible X E01-0210-118 3 3 3 2nd Generation Continuum Compatible Driver Description Uses Modbus RTU XDriver. power monitoring Manufacturer Equipment* Descrip.
Andover Continuum Third Party Interfaces pumps Manufacturer Grundfoss Equipment* Descrip./Model Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible Genibus Pumps & Motors X E01-0210-172 3 3 Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible 2nd Generation Continuum Compatible Driver Description Full control and monitoring of pumps and motors on RS-485 Genibus network.
Andover Continuum Third Party Interfaces variable speed drives Manufacturer Equipment* Descrip./Model Driver Type TAC File Reference Number* Infinity Compatible 1st Generation Continuum Compatible 2nd Generation Continuum Compatible 3 ABB ACH500 X E01-0210-118 3 3 Danfoss VLT3000 Series X E01-0210-131 3 3 Driver Description Uses Modbus RTU protocol to extract data from individual drives. Gives full control & monitoring of all drive parameters.
Field Devices
Andover Continuum Temperature Control Room & Interactive Sensors Wall Mount Sensor TAC’s wall mount temperature sensors provide accurate, reliable measurement of interior space temperature. The thermistor is encapsulated with a low mass, high-conductivity thermal compound for good heat transfer characteristics. It is housed in an attractive, well-ventilated plastic enclosure.
Andover Continuum Temperature Control Interactive Sensors Smart Sensor The TAC Smart Sensor combines an attractive display with a room temperature sensor to provide users with a cost effective way to view or modify local terminal unit operation. It is designed for use with I2 controllers and can also accomplish many local control and monitoring tasks.
Andover Continuum Temperature Control Display Modules Infistat Display Interface The Infistat Display Module provides a convenient, programmable interface to your building management system. Provides authorised operators quick and easy access to HVAC or security information and enables them to adjust personal comfort levels with little or no training. The Infistat can co-exist with other Continuum I/O modules, such as the UI-8-10, DI-8, AO-4-8 etc. (up to 32 modules per single NetController).
Andover Continuum Field Devices General HVAC and Other Field Devices The temperature control sensors featured on the previous pages of this catalogue are specific to Andover Continuum. In addition, TAC’s Field Device Product Division offers a comprehensive portfolio of field devices to meet all our customers’ needs. For further details, contact your local TAC sales office, or download the current set of Field Device Catalogues from our website: www.tac.
Andover Controls XXXXXX XXXXXXX Continuum Compatibility XXXXXXMatrix XXXXXX Andover Continuum Software and Firmware Compatibility Matrix Versions 1.7 through 1.81 Note: ALL Andover Continuum workstations and web.Client Application Servers must be at the exact same software rev. CyberStation/web.Client Software Version Last Updated: June 15, 2007 1.7 1.71 1.73 1.74 1.
Andover Controls XXXXXX XXXXXXX Continuum Compatibility XXXXXXMatrix XXXXXX Andover Continuum Software and Firmware Compatibility Matrix Versions 1.4 through 1.62 LAN Configuration Note: ALL Andover Continuum workstations and web.Client Application Servers must be at the exact same software rev. CyberStation/web.Client Software Version Last Updated: June 15, 2007 1.4 1.5 1.51 1.52 1.53 1.6 1.62 Win NT 4.0 Server SP6a, DB Server OS Win NT 4.
Notes
Notes
Malmö, Sweden +46 40 38 68 50 Rockford, IL +1 888 444 1311 Signapore +65 6776 3166 http://www.schneider-electric.com/buildings CAT-CONTINUUM-EU.BU.N.EN.10.2008.0.00.CC On October 1st, 2009, TAC became the Buildings Business of its parent company Schneider Electric. This document reflects the visual identity of Schneider Electric, however there remains references to TAC as a corporate brand in the body copy.
