c.LOGiC lite-Interface C1-C20 For navigation systems Mercedes Benz Comand 2.0 Comand APS CD Product features • full plug and play multimedia interface • 1 AV-input with separate IR-control channel • control of after-market devices, e.g. DVB-T tuner, DVD-player, DVD-changer, … • after-market rear-view camera input activation • automatic switching to rear-view camera input (only from c.LOGiC-mode) • rear-view camera power (+12V max. 1A) • power on remote out trigger signal (+12V max.
Contents 1. Prior to Installation 1.1. 1.2. Delivery contents Check compatibility of vehicle and accessories 2. Connection schema 3. Installation 3.1. 3.2. 3.3. 3.3.1. 3.3.2. 3.3.3. Connections to the Comand Interconnecting Interface-box and harnesses Connecting peripheral devices AV-source Installing AV-source’s IR-sensor additionally After-market rear-view camera 4. Operation 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. Activation of the video-in-motion function Selecting the c.
Legal Information By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. This product should only be used while standing or to display fixed menus or rear-view-camera video when the vehicle is moving, for example the MP3 menu for DVD upgrades.
1.2. Check compatibility of vehicle and accessories Requirements Vehicle Mercedes Benz C-Class (W203) til 04/2004, CL-Class (C215) from 09/2002 til 09/2003, CLK-Class (C208 W208) all years, CLK-Class (C209 W209) til 05/2004 , E-Class (W210) all years , G-Modell (W463) til 03/2007, ML-Class (W163) all jears, S-Class (W220) from 09/2002 til 09/2003, SL-Class (R230) til 06/2004 Navigation Comand 2.0, Comand APS CD Limitations Must NOT be installed.
2. Connection schema 3. Installation Page 4 Switch off ignition and disconnect the vehicle’s battery! If according to factory rules disconnecting the battery has to be avoided, it is usually sufficient to put the vehicle in sleep-mode. In case the sleep-mode does not show success, disconnect the battery with a resistor lead. Version 23.05.
3.1. Connections to the Comand Place of installation is behind the Comand. Remove the head-unit from the dash-board. Remove shell from female 18pin AMP connector of C1C-MB20. Transfer pins 2 (red), 11 (white), 3 and 12 (black) from female 18pin AMP connector of C1C-MB20 to corresponding slots of female 18pin AMP connector of factory harness. If occupied remove and isolate factory wires (take notes before removing).
3.2. Interconnecting Interface-box and harnesses Plug harness C1C-MB20 into 12pin Molex of Interface-box C1C-M01. 3.3. Connecting peripheral devices It is possible to connect one after-market AV-source and an after-market rear-view camera to the c.LOGiC Interface. Page 6 Before final installation of the peripheral devices, we recommend to test-run the c.LOGiC functions to detect incompatibility of vehicle, navigation, factory accessories or peripheral devices as soon as possible. Version 23.05.
3.3.1. AV-source The c.LOGiC interface has the possibility to connect and remotely control by navigation buttons one pre-programmed device. The device list in the device control table (Appendix A) shows the pre-programmed remote channels and the related IR-remote cables STA-xxx which must be ordered separately for the control of the device. Using the respective STA-xxx IR-control cable, interconnect the blue female 3pin AMP connector of harness C1C-MB20 and the IR-port of the AV-source.
3.3.3. After-market rear-view camera Connect the video RCA of the after-market rear-view camera to female RCA connector R-CAM IN of Interface-box C1C-M01. Connect the green wire of the 4pin cable to the camera power supply (+12V max. 1A) of the after-market rear-view camera and the grey wire to ground of the vehicle. The green wire is high (+12V max. 1A) when reverse gear is engaged. The white wire is not connected and has to be isolated.
4.3. Assigning device control After selecting the c.LOGiC as current AV source, longpress the number “1”-button or shortpress the “RET”-button. The display in the instruments will show “TV 1” and “RC01”. Turn right knob until the device-related IR-code as described in device control table (appendix A) is reached. Push right knob to confirm the assignment. If the vehicle has no MFD display in the instrument panel, you must count the notches when turning the knob (to the right +1, to the left -1).
Button assignment table c.LOGiC Comand 2.
4.6. Audio settings To enter the Comand’s audio settings menu press button 12. 5. Specifications Operation voltage Stand-by power drain Operation power drain Power consumption Temperature range Weight Measurements (box only) B x H x T 10.5 – 14.8V DC <1mA 240mA 3W -30°C to +80°C 95g 106 x 30 x 71 mm 6. Connections (Interface-box) 7. Technical Support Caraudio-Systems Vertriebs GmbH manufacturer/distribution Rheinhorststr.
