IMPRESSA Z5 Art. Nr.
= Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 a b c Fig. 11 Fig. 13: Correct assembly of the cappuccino nozzle Make sure there is always a small gap between the rear cappuccino nozzle and the connection piece. This will guarantee perfect operation of the cappuccino nozzle. Fig. 12 Fig. 13 1 Fig.
7 8 6 9 14 5 15 10 11 4a 12 13 2b 16b 16a A B C 4b 3 2a 1 D E F G H I J K L M
Description of the machine 1. Drip tray 2. a) Drip grate b) Cup platform 3. Coffee grounds tray and container 4. a) One Touch Cappuccino nozzle* long spout b) One Touch Cappuccino nozzle* short spout 5. Water tank with handle and level indicator 6. Water tank cover 7. Cover for bean tank and coffee powder tank 8. Aroma preservation cover 9. Filler funnel for pre-ground coffee 10. Control panel 11. Height-adjustable coffee spout 12. Height-adjustable hot water spout 13. Cup illumination 14.
Contents 1. Safety information ..............................................page 1.1 Warning..................................................page 1.2 Precautions..............................................page 2. Preparing the IMPRESSA Z5 ...............................page 2.1 Check supply voltage..................................page 2.2 Check electrical fuse ..................................page 2.3 Fill water tank .........................................page 2.4 Fill coffee beans .................
Introduction Thank you for purchasing the IMPRESSA Z5. To ensure perfect functioning of your IMPRESSA, carefully read this operating manual and keep it for future reference. Should you need more information or if you encounter particular problems not specified in these operating instructions in sufficient detail, either contact us directly or contact your local authorized dealer. You can download other languages from the JURA website at www.jura.
2.2 Check electrical fuse The IMPRESSA Z5 is designed for an electric current of 10 amperes. Check if the electrical fuse has sufficient capacity. 2.3 Fill water tank Only use fresh, cold water. Never fill in milk, mineral water or other liquids. Remove the water tank and rinse it with cold tap water thoroughly (Fig. 1). Then fill the water tank and reinstall it. Make sure to install the tank properly, it must engage audibly.
2.6.2 Stainless steel vacuum milk container (16b) Always clean the stainless steel vacuum milk container after you have used it. Rinse it with warm water, and with some detergent if necessery Remove the riser tube inside the milk container as well as the hose connection on the outside and give these parts including the lid a good rinse with clear water. Never use scouring agents, bleach, solvents or abrasive pads for cleaning. Leave the vacuum milk container OPEN if it’s not being used.
CONFIRMED √ PRESS MAINTENANCE Maintenance key (C) lights up. Place a cup each under the height-adjustable coffee spout (12) and the cappuccino nozzle (4) and press the maintenance key (C). SYSTEM FILLS The system now fills up automatically. While it is doing so, the maintenance key flashes. (A little water will leak from the cappuccino nozzle (4), then from the hot water spout (12).
COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO Turn the Rotary Switch (B) until the following message is displayed: HARDNESS 16°dH Now press the Rotary Switch (B) to start programming. HARDNESS 16°dH Now turn the Rotary Switch until the correct water hardness is set. HARDNESS 20°dH (example) Confirm the selected setting by pressing the Rotary Switch (B).
Place a sufficiently large receptacle (min. 0.5 litres) under the cappuccino nozzle (4). We recommend attaching the short spout (4b). Press the maintenance key (C) to start rinsing the filter. FILTER RINS Filter rinsing stops automatically. UNIT IS HEATING COFFEE READY You have now activated the filter. The programming step for adjusting your machine to the correct water hardness is therefore no longer displayed. The water might be slightly discoloured (no hazard to health).
6. Rinsing the machine If the coffee machine is switched off and has cooled down, you will be prompted to start a rinsing cycle when switching the machine back on. The machine automatically performs a rinsing cycle when you switch it off. PRESS MAINTENANCE Place a cup under the height-adjustable coffee spout (11). Press the maintenance key (C). RINSING COFFEE READY You can also trigger a rinsing cycle manually from the maintenance menu at any point in time (see Chapter 15.3).
COFFEE READY To stop the brewing process prematurely, press any of the product keys. You can pre-select the strength of your coffee when the machine is ready to brew ( PLEASE SELECT). To do so, turn the Rotary Switch (B) until the display indicates the desired coffee strength and then press the coffee key of your choice (key F for special coffee). CAPPUCCINO MILK The machine stops drawing milk automatically as soon as the set amount of milk (in SEC) has been used.
CAPPU RINSE Place a sufficiently large receptacle (ca. 0.5 litres) under the cappuccino nozzle (4). Turn the selector switch (1, Fig. 9) to the steam range (c, Fig. 9). Press the maintenance key (C) to start the cappuccino rinsing cycle. CAPPUCCINO RINSING COFFEE READY You can also trigger a cappuccino rinsing cycle manually from the maintenance menu at any point in time (see Chapter 15.3). 9.
MACHINE IS CLEANING COFFEE READY 9.4 Cleaning the cappuccino nozzle Despite the cappuccino cleaning cycle, you should regularly disassemble the cappuccino nozzle and rinse it under running water. Remove the cappuccino nozzle from the IMPRESSA and take it apart as shown in Fig. 11. Thoroughly rinse all the parts of the nozzle under running water. Re-assemble the cappuccino nozzle and attach it to your IMPRESSA. 10.
You can change the amount of water set while the machine is dispensing hot water. To do so, turn the Rotary Switch (B) until the display indicates the required amount (ML). The amount of water can be selected in increments of 5 ML. To stop the brewing process prematurely, press any of the keys. The amounts given in ML are approximate values and may vary from the effective quantity. We recommend always using powder from fresh coffee beans or pre-ground, vacuum-packed coffee.
Switch the IMPRESSA off with the ON / OFF switch GOODBYE The coffee spout is rinsing. RINSE LEFT SPOUT PRESS BUTTON Press the maintenance key (C) to continue rinsing. GOODBYE (A). When switching the machine off, there may be a hissing sound. This is due to a normal process being performed by the system. It is recommended to switch off the machine with the power switch if you intend not to use your IMPRESSA for a longer time. 14. Settings 14.
When the machine has dispensed as much milk as you wanted, briefly press the key once more. CONFIRMED √ The amount of milk to be dispensed is now programmed. ENOUGH ? PRESS BUTTON When you have made as much coffee as you wanted, briefly press the key once more. CONFIRMED √ The amount of coffee to be made is now programmed. You can also make the cappuccino settings in the programming mode (see Chapter 15.6) 14.
15. Programming The IMPRESSA leaves the factory with a number of default settings that allow you to make coffee without having to program the machine first. You can, however, adjust various parameters to make the coffee suit your personal taste. The following parameters can be programmed: Filter Water hardness Maintenance Temperature Coffee strength Cappuccino Milk Save energy Time Automatic switch-on time Automatic switch-off time Information Rename Language Display 15.
COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: TEMPERATURE Press the Rotary Switch (B) to start programming. TEMPERATURE COFFEE READY Then press a product key of your choice. 1 ESPRESSO (example) NORMAL Turn the Rotary Switch until the required temperature is set.
√ AROMA Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.6 Cappuccino programming You can also make the cappuccino settings in the programming mode or as described in Chapter 14.2 “Cappuccino setting”. COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal.
Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: MILK 20 SEC (example) Now press the Rotary Switch (B) to start programming. MILK 20 SEC (example) Now turn the Rotary Switch (B) until the required amount of milk is set. MILK 28 SEC (example) Confirm the selected setting by pressing the Rotary Switch (B).
Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.9 Setting the time Save energy: No COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: TIME 12:45 (example) Now press the Rotary Switch (B) to start programming. TIME HOURS 12:45 Turn the Rotary Switch (B) to set the hours.
TIME 13:50 Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.10 Programming the automatic switch-on time COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: UNIT ON —:— Now press the Rotary Switch (B) to start programming.
OFF AFTER 5 HRS Now press the Rotary Switch (B) to start programming. OFF AFTER 5 HRS Turn the Rotary Switch (B) to set the switch-off time. OFF AFTER 4 HRS (example) Confirm the automatic switch-off time by pressing the Rotary Switch (B). CONFIRMED √ OFF AFTER 4 HRS Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY 15.
COFFEE READY 15.13 Renaming This function allows you to rename the different products as well as change the welcome and end text. COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: RENAME Now press the Rotary Switch (B) to start programming. RENAME PRODUCT NAME Turn the Rotary Switch further to select WELCOME MESSAGE or END MESSAGE. Press the Rotary Switch (B).
15.14 Programming the language COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: LANGUAGE ENGLISH Now press the Rotary Switch (B) to start programming. LANGUAGE ENGLISH Turn the Rotary Switch (B) to set the language. LANGUAGE ENGLISH (example) Confirm the selected language by pressing the Rotary Switch (B).
Now turn the Rotary Switch (B) until the following message is displayed: EXIT Now press the Rotary Switch (B) to leave the programming mode. COFFEE READY Changing the time format COFFEE READY Press the Rotary Switch (B) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (B) until the following message is displayed: SETTINGS Now press the Rotary Switch (B) to start programming. SETTINGS UNIT Turn the Rotary Switch (B).
On the IMPRESSA Z5 Chrome we recommend that the cup platform (2b) is removed first followed by the drip tray and the coffee grounds tray with bin. 16.2 Emptying the coffee grounds GROUNDS EMPTY If this information is displayed, the machine will no longer make coffee. The machine will still make hot water and frothed milk, however. Empty the coffee grounds container (3).
Insert the drip tray (3). COFFEE READY Open the cover of the bean tank (7) and remove the aroma preservation cover (8). Remove any beans with a vacuum cleaner. Insert the key (Fig. 12). Now turn the key conter-clockwise until the jammed stone is released. Remove any remaining powder with a vacuum cleaner. Fill up with fresh beans. 16.6 Filling the bean tank COFFEE READY FILL BEANS If this information is displayed, the machine will no longer make coffee.
After another 10 products, the display will change. Please run the cleaning cycle immediately (see Chapter 17). CLEAN NOW CLEAN (flashing) 16.11 Information about decalcify Lime scale builds up in the IMPRESSA as a result of normal use. The degree of calcification depends on the hardness of the water you use. The IMPRESSA Z5 recognizes when you should run a decalcifying cycle. The machine will still make coffee, hot water and frothed milk.
TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the container (3). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA. PRESS BUTTON Place a sufficiently large receptacle (ca. 0.5 litres) each under the height-adjustable coffee spout (11) and under the cappuccino nozzle (4). Press the maintenance key (C). MACHINE IS CLEANING You will hear an acoustic signal.
Once started, the decalcifying program must not be interrupted. Always wait until the decalcifying agent has been used up and the tank is empty. Never fill in additional descaling agent. COFFEE READY DESCALE Press the maintenance key (C). TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the container (3). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA Z5.
You will hear an acoustic signal. TRAY / GROUNDS EMPTY Empty the drip tray (1) and the coffee grounds tray with the container (3). TRAY MISSING Place the empty, clean drip tray (1) and the coffee grounds tray with the container (3) back into the IMPRESSA. COFFEE READY You can also trigger a decalcifying cycle manually from the maintenance menu at any point in time (see Chapter 15.3). 20.
21. Problems Problem Cause Remedy Very loud noise coming from the grinding gear Foreign body in grinding gear Please refer to Chapter 16.8 Frothing spout squirts Milk hose not properly attached Make sure the milk hose is properly attached Too little froth when frothing milk Cappuccino nozzle clogged Clean nozzle (Chapter 9.
22. Legal information 23. Technical data These operating instructions contain all the information required for using, operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover any conceivable application. The machine was designed for private household use.
