IMPRESSA S9/S7 avantgarde Art. Nr.
Legend: DISPLAY: serves as information. DISPLAY: please follow the instructions shown. = Note = Important = Tip JURA Elektroapparate AG, CH-4626 Niederbuchsiten, Internet http://www.jura.
Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 12 2 1 3 Fig. 9 Fig. 10 Fig. 11 Fig. 13 Fig. 14 Fig.
16 17 Description of the machine 18 15 14 19 13 12 11 10 9 8 7 6 5 4 20 21 22 23 24 25 26 3 27 2 1 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27.
Contents 1. Safety information ..............................................page 1.1 Warnings ................................................page 1.2 Precautions..............................................page 2. Before you start using the IMPRESSA S9/S7 avantgarde ........................................................page 2.1 Checking the mains voltage ..........................page 2.2 Checking electrical fuse...............................page 2.3 Filling the water tank ............................
Before you begin 1.2.Precautions Congratulations on having bought this IMPRESSA S9/S7 avantgarde! Never expose the coffee machine to weather (rain, snow, frost), never touch the machine when your hands are wet. Place the IMPRESSA on a firm, level base that is resistant to any water that may leak. Never stand on hot or warm surfaces (oven hobs). Keep out of the reach of children. If you intend not to use the machine for a longer time (holidays, etc.), always turn off the power switch.
2.3 Filling the water tank Only use fresh, cold water. Never fill the water tank with milk, mineral water or other liquids. Take out the water tank and thoroughly rinse it out with cold tap water (Fig. 1). Then fill it with water and place it back into the coffee machine. Make sure the tank is installed correctly and that it engages properly. 2.
Place a receptacle under the Professional Cappuccino Frother (24) and press one of the Steam keys . The system now fills up automatically. A little water will leak from the frothing jet. SYSTEM FILLING HEATING UP PRESS RINSE Place a cup under the height-adjustable coffee spout (18). Press Rinse . MACHINE RINSING Now the water lines are flushed with fresh water. A little water will leak from the coffee spout (18).
Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 5. Using a CLARIS plus filter cartridge When using the CLARIS plus filter cartridge correctly, decalcifying your IMPRESSA will no longer be necessary. For more information on the CLARIS plus filter cartridge refer to the brochure “CLARIS plus. Hard on limescale. Gentle on your coffee machine.” 5.
Place a sufficiently large receptacle (min. 0.5 litres) under the Professional Cappuccino Frother (24) and press one of the Steam keys to start the filter rinsing process. FILTER RINSING Filter rinsing stops automatically. SELECT PRODUCT You can also trigger a change of filter manually from the Maintenance menu at any point in time (only if the filter has been activated) - see Chapter 13.3. 6.
The coffee brewing process stops automatically as soon as the set amount of water has run through. SELECT PRODUCT To stop the brewing process prematurely, press any of the product keys. We recommend always using powder from fresh coffee beans or pre-ground, vacuum-packed coffee. Never fill in more than 2 scoops of powder. The filler funnel is no storage tank. Make sure the coffee powder you use is not too fine. This may block the system and cause the coffee only to drip out of the coffee spout.
You can also change the amount of water set while the machine is brewing coffee. Open the programming door. Turn the Rotary Switch (4) until the display indicates the required amount (ML). The amount of water can be selected in increments of 5 ML. The amounts given in ML are approximate values and may vary from the effective quantity. 10. Frothing milk The IMPRESSA is ready to froth milk when both Steam key lights light up constantly. If the lights are off, press one of the two Steam keys .
Dip the milk pipe into the second receptacle containing the Auto-Cappuccino Cleaner. Press the Extended Steam draw-off button . As soon as the liquid has flown through, press the Extended Steam draw-off button again. Fill the receptacle with fresh water. Immerse the milk pipe in the receptacle. Press the Extended Steam draw-off button . As soon as the fresh water has flown through, press the Extended Steam draw-off button again. The machine is ready to dispense drinks.
12.3 Maintenance You can activate the following maintenance functions from this program item: RINSE MACHINE, CLEAN MACHINE, DE-SCALE MACHINE, CHANGE FILTER. “DE-SCALE machine” is not displayed if you are using a CLARIS plus filter cartridge and the filter is set to “YES”. “CHANGE FILTER” is not displayed if you are not using a CLARIS plus filter cartridge and the filter is set to “NO”. SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal.
12.5 Setting the amount of water for coffee, espresso and coffee à la carte 12.6 Programming the temperature for coffee, espresso and coffee à la carte The system’s basic settings include pre-defined amounts of water (coffee 130 ml, espresso 60 ml, 2 coffees 260 ml, coffee à la carte 145 ml). However, these can be modified as required. You can adjust the temperature for each type of coffee separately. The temperature can be set to 2 different levels (NORMAL, HIGH).
12.7 Programming the water portion The system’s basic settings include a pre-defined amount of water (225 ml). However, this amount can be modified as required. SELECT PRODUCT Open the programming door (3). Press the Rotary Switch (4) until you hear an acoustic signal. FILTER NO or YES Turn the Rotary Switch (4) until the following message is displayed: WATER PORTION Press the Rotary Switch (4) to activate the program item.
Now press the Rotary Switch (4) to start programming. ECONOMY MODE Now turn the Rotary Switch (4) until the required economy mode is displayed. ECONOMY MODE 2 (example) Confirm the selected setting by pressing the Rotary Switch (4). ECONOMY MODE 2 (example) Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode.
TIME 13:00 (example) Press the Rotary Switch (4) to confirm the hours and to activate the minutes. TIME 13:00 Turn the Rotary Switch (4) to set the minutes. TIME 13:50 (example) Press the Rotary Switch (4) to confirm the minutes. TIME 13:50 Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 12.
Turn the Rotary Switch (4) until the following message is displayed: OFF AFTER 5 HRS Now press the Rotary Switch (4) to start programming. OFF AFTER 5 HRS Turn the Rotary Switch (4) to set the switch-off time. OFF AFTER 4 HRS (example) Confirm the set switch-off time by pressing the Rotary Switch (4). OFF AFTER 4 HRS Now turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode. SELECT PRODUCT 12.
Turn the Rotary Switch (4) to change the time format. DISPLAY AM / PM / ML Confirm your selection by pressing the Rotary Switch (4). DISPLAY AM / PM / ML Turn the Rotary Switch (4) to change the unit of measurement. DISPLAY AM / PM / OZ Confirm your selection by pressing the Rotary Switch (4). DISPLAY AM / PM / OZ Turn the Rotary Switch (4) until the following message is displayed: EXIT Now press the Rotary Switch (4) to leave the programming mode.
13. Maintenance 13.3 Emptying the drip tray 13.1 Filling the water tank FILL WATER TANK If this information is displayed, the machine will no longer make coffee. Refill water as described in Chapter 2.3. SELECT PRODUCT The water tank should be rinsed out and filled with fresh water daily. Always use fresh, cold water. Never fill the water tank with milk, mineral water or other liquids. 13.
13.6 Removing stones from the grinding gear Switch the machine off using the ON / OFF key (11). Turn the power switch (27) off. Open the lid of the bean tank (16) and remove the aroma preservation cover (15). Remove any beans with a vacuum cleaner. Remove the screw in the bean tank (Fig. 9) and fold the finger protection device up (Fig. 10). Insert the key (Fig. 11). Now turn the key counter-clockwise until the jammed stone is released. Remove any remaining powder with a vacuum cleaner.
SYSTEM EMPTYING When the process has been completed, the IMPRESSA switches itself off. 14. Cleaning The IMPRESSA features an integrated cleaning program. The process takes approx.15 minutes. Please only use original JURA cleaning tablets: their formula is especially tailored to JURA coffee machines. Please note that the use of unsuitable cleaning agents may cause damage to your machine and could leave unfavourable residues in the water.
You will hear an acoustic signal. ADD TABLET / PRESS RINSE Open the lid of the filler funnel for pre-ground coffee (17). Drop an original JURA cleaning tablet inside (Fig. 12) and close the lid. Press Rinse . MACHINE CLEANING You will hear an acoustic signal. EMPTY TRAY / EMPTY GROUNDS Empty out the drip tray (1) and integrated coffee grounds bin. TRAY MISSING Place the empty, clean drip tray (1) and integrated coffee grounds bin back into the IMPRESSA.
Completely dissolve the content of one blister (3 tablets) in a receptacle containing 0.6 litres of water, and pour the mixture into the water tank. Place the water tank back into the machine. Remove the Professional Cappuccino Frother (24) from the machine. Place a tall receptacle under the connecting part of the Professional Cappuccino Frother and press one of the Steam keys . MACHINE DE-SCALING You will hear an acoustic signal. OPEN TAP Place the receptacle under the hot water spout (25).
16. Disposal Please dispose of old machines in an environmentally neutral manner Old machines contain valuable recyclable materials, which should be sent off for recycling. Therefore please dispose of old machines via suitable collection systems. 17. Tips for perfect coffee Height-adjustable coffee spout (18) You can adjust the height of the coffee spout to the size of your cups. Grinding degree Refer to Chapter 2.5 “Adjusting the grinding gear”.
18. Problems Problem Cause Remedy Grinding gear makes a very loud noise Foreign body in the grinding gear Please refer to Chapter 14.6 Too little froth when frothing milk Professional Cappuccino Frother clogged Clean frother (Chapter 11.
19. Legal information 20. Technical data These operating instructions contain all the information required for operating and maintaining the machine properly. Knowledge of and compliance with the specifications contained in these operating instructions is required for using the machine safely as well as for operational safety and safety during maintenance. These operating instructions cannot cover all conceivable applications. The machine was designed for private household use.
