The IMPRESSA C5 Manual The ‘IMPRESSA C5 Manual’ has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.
Table of contents Your IMPRESSA C5 Control elements and accessories 4 Proper use 6 For your safety 6 The IMPRESSA C5 Manual 8 Symbol description ......................................................................................................................................8 1 IMPRESSA C5 – Click & Drink 9 Coffee that fulfils your wildest dreams ....................................................................................................9 Click & Drink...........................................
Table of contents Cleaning the machine ............................................................................................................................. 29 Descaling the machine ............................................................................................................................. 31 Rinsing the Easy Cappuccino Frother ....................................................................................................33 Cleaning the Easy Cappuccino Frother ................
Control elements and accessories Control elements and accessories Mains cable (see rear side) de) On/Off button Switch for setting fineness of grind 1 2 17 16 3 15 14 13 4 12 11 5 10 6 9 7 8 4 Figure: IMPRESSA C5 platinum 1 Filler funnel for pre-ground coffee 9 Drip tray 2 Cup tray 10 Cup platform 3 Water tank with level indicator 11 JURA Cappuccino Cleaner 4 Overview of maintenance indicators 12 Drawer with coffee grounds container 5 CLARIS filter cartridge 13 Height-adjus
Control elements and accessories 1 2 3 4 5 6 7 8 Symbol display Maintenance field 1 Symbol display 5 Maintenance indicator 2 Rotary Switch 6 Access door 3 Light segments 7 Maintenance field 4 Symbols 8 Indicators a s d f P h j k 1 Espresso 2 Espressos 1 coffee 2 coffees P (Programming) Maintenance y x c v b n Water tank Coffee grounds container Bean container Cleaning button Descaling button Filter button Pre-ground coffee Steam 5
Important information Proper use The machine has been designed and built for domestic use. It should only be used to prepare coffee and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use. Before using the machine always carefully read and comply with all these instructions. Keep this manual close to the IMPRESSA and, if appropriate, pass it on to the next user.
Important information A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire: Never allow the power cable to loosely hang down. The power cable can be tripped over or damaged. Protect your IMPRESSA from environmental influences such as rain, frost and direct sunlight. Do not put the IMPRESSA, cable or connections in water. Do not put the IMPRESSA or any individual parts in the dishwasher. Switch your IMPRESSA off before cleaning it.
The IMPRESSA C5 Manual The IMPRESSA C5 Manual You are holding the manual for your IMPRESSA C5 in your hand. The information contained in this manual will help you to familiarise yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers. Chapter 2, ‘Preparing and using your IMPRESSA for the first time’, explains step-by-step how to set up and prepare the IMPRESSA.
1 IMPRESSA C5 – Click & Drink 1 IMPRESSA C5 – Click & Drink Coffee that fulfils your wildest dreams JURA‘s avowed mission is to develop superior machines which get the best out of every blend and roast of coffee. This it delivers through a unique, intelligent pre-brew system combined with loving attention to detail. Click & Drink The IMPRESSA C5 demonstrates just how wonderful a perfect cup of coffee can taste and how easy it is to prepare one.
1 IMPRESSA C5 – Click & Drink p JURA on the Internet Connector System© The Connector System© allows one to use the Easy Cappuccino Frother, which is fitted as standard, a hot water nozzle for an even jet of water and the optionally available 2-stage frothing nozzle or the Professional Cappuccino Frother for perfect milk foam or hot milk. Visit us on the Internet. @ At www.jura.com you will find interesting and up-to-date information on your IMPRESSA and on every aspect of the subject of coffee.
2 Preparing and using your IMPRESSA for the first time 2 Preparing and using your IMPRESSA for the first time This chapter provides you with the information you need to use your IMPRESSA without any problems. You will prepare your IMPRESSA step-by-step for your first coffee experience using it. Setting up When setting up your IMPRESSA, please note the following: Set the IMPRESSA down on a horizontal surface that is not sensitive to water.
2 Preparing and using your IMPRESSA for the first time l Fill the bean container with coffee beans, then close the aroma preservation cover and the bean container cover. First-time use WARNING If the machine is operated with a defective power cable, there is a danger of electric shock. l Never use a machine which has a defective power cable. Precondition: the water tank must be full. l Remove the protective film from the symbol display. l Insert the mains plug into a power socket.
2 Preparing and using your IMPRESSA for the first time Using and activating filter Your IMPRESSA no longer has to be descaled if you are using CLARIS filter cartridges. o Perform the ‘Using filter’ operation without a break. This will ensure that your IMPRESSA always produces its best. @ You can also try out the ‘Using filter’ operation online. Visit the Knowledge Builder on www.jura.com. l Remove the packaging on the CLARIS filter cartridge. l Remove the water tank and empty it.
2 Preparing and using your IMPRESSA for the first time l Place a receptacle (containing at least 500 ml) under the Easy Cappuccino Frother. l If the milk pipe is connected, remove it. r l Turn the switch in the anticlockwise direction. Rinsing of the filter will now begin. The light segment by the switch will light up. o You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter.
2 Preparing and using your IMPRESSA for the first time Assessing and setting water hardness The harder the water is, the more frequently the IMPRESSA needs to be descaled. It is therefore important to set the water hardness. o However, if you are using the CLARIS filter cartridge and have activated the filter, you will not be able to adjust the water hardness. The symbols in the symbol display show the configured degree of water hardness. The number of symbols corresponds to the relevant level.
2 Preparing and using your IMPRESSA for the first time b l Hold down the Descaling button until the Descaling indi- ä m Adjusting grinder CAUTION cator b lights up. The Descaling indicator b and the symbols A S D will now light up. l Turn the Rotary Switch until the four symbols a s d f light up. l Press the Rotary Switch to confirm the level 4 setting. The IMPRESSA is ready for use again. The water hardness is now set. You can adjust the grinder continuously to suit the roast of your coffee.
2 Preparing and using your IMPRESSA for the first time Switching on When the IMPRESSA is switched on, a prompt to perform a rinse operation automatically appears. G l Press the On/Off button to switch the IMPRESSA on. m Switching off As long as the machine is heating up, the Maintenance symbol h will flash. The Maintenance symbol h lights up. l Place a receptacle under the coffee spout. l Press the Rotary Switch to start the rinse operation. The coffee spout will be rinsed.
3 Familiarising yourself with the control options 3 Familiarising yourself with the control options With the IMPRESSA, you can prepare an excellent coffee speciality at the touch of a button. You also have the option of adjusting the coffee strength and amount of water to your personal taste while the coffee is brewing. This chapter will show you how to operate the machine with the aid of examples.
3 Familiarising yourself with the control options Example: this is how to prepare an Espresso. l Place an Espresso cup under the coffee spout. ä l Turn the Rotary Switch to the 1 Espresso setting a. m l Press the Rotary Switch to initiate preparation of the Espresso. The 1 Espresso symbol a will now flash, and the pre-set amount of water wll flow into the cup. Drink preparation stops automatically.
3 Familiarising yourself with the control options ä l While the grinder is running, turn the Rotary Switch in a clockwise direction until three light segments have lit up. The grinding operation stops, brewing begins and the predefined quantity of water flows into the cup. Drink preparation stops automatically. Adjusting the permanent cup size settings It is easy to adjust the amount of water for all coffee specialities to the cup size for good.
4 Preparing drinks at the touch of a button 4 Preparing drinks at the touch of a button This chapter will explain how to prepare coffee specialities, milk and hot water. Chapter 3, ‘Familiarising yourself with the control options’, will teach you how to adjust the settings to your personal preferences. o You can stop the machine at any time while a coffee speciality is being prepared. To do this press the Rotary Switch. @ You can also try out the preparation of coffee specialities online.
4 Preparing drinks at the touch of a button l Place a cup under the Easy Cappuccino Frother. ä l Turn the Rotary Switch so that it points to the Steam symbol k. m l Press the Rotary Switch to confirm your choice. The Steam symbol k will continue flashing until r t the IMPRESSA has warmed up. As soon as the required temperature has been reached, the light segment by the switch will flash. l Turn the switch in the anticlockwise direction. The milk foam will be prepared.
4 Preparing drinks at the touch of a button o If you have added too little pre-ground coffee, the IMPRESSA will come to a halt ready for further use. Example: proceed as follows to prepare a cup of coffee using preground coffee. l Take the measuring spoon for pre-ground coffee out of the Welcome Pack. ä l Turn the Rotary Switch so that it points to the pre-ground coffee symbol j. m l Press the Rotary Switch to confirm your choice. The pre-ground coffee symbol j will flash.
4 Preparing drinks at the touch of a button Milk foam Precondition: your IMPRESSA is ready to use, the Easy Cappuccino Frother is mounted. l Take the milk pipe out of the Welcome Pack. l Take the protective cap off the Easy Cappuccino Frother. l Attach the milk pipe to the frother. l Insert the other end in a milk Tetrapack or connect it to a milk container. l Place a cup under the Easy Cappuccino Frother. ä l Turn the Rotary Switch so that it points to the Steam symbol k.
4 Preparing drinks at the touch of a button l Take the hot water nozzle out of the Welcome Pack. l Insert this into the Connector System with a light turning © motion. l Place a cup under the hot water nozzle. Precondition: your IMPRESSA is ready for use. r l Turn the switch in the anticlockwise direction. The light segment on the switch will light up and hot water will flow into the cup. t l Turn the switch in the clockwise direction when there is sufficient water in the cup.
5 Adjusting the permanent settings in programming mode 5 Adjusting the permanent settings in programming mode Automatic switch-off By instructing your IMPRESSA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after the preset time following the last action on the machine.
6 Maintenance 6 Maintenance Your IMPRESSA has the following integrated maintenance programs: Rinse the machine Change the filter Clean the machine Descale the machine p p p p The illuminated maintenance indicator draws your attention to the maintenance actions that are necessary. Open the access door and note the further indicators in the maintenance field. In the example shown on the left, your IMPRESSA is prompting you to clean it.
6 Maintenance Precondition: the IMPRESSA is ready for use. l Place a receptacle under the coffee spout. ä l Turn the Rotary Switch so that it points to the Maintenance symbol h . m l Press the Rotary Switch to start the rinse operation. The rinse operation now starts and the Maintenance symbol h flashes. Rinsing stops automatically. Your IMPRESSA is ready for use. Changing the filter o After 50 litres of water have been dispensed, the filter will cease to work.
6 Maintenance l Place a receptacle (containing at least 500 ml) under the Easy Cappuccino Frother. l If the milk pipe is connected, remove it. n l Hold down the Filter button until the Filter indicator n flashes. The light segment by the switch will now flash. r l Turn the switch in the anticlockwise direction. Rinsing of the filter will now begin. The light segment by the switch will now light up. o You can interrupt rinsing of the filter at any time. To do this, turn the switch clockwise.
6 Maintenance @ Try out the ‘Cleaning the machine’ operation online. Visit the Knowledge Builder on www.jura.com. Cleaning following a prompt To clean your IMPRESSA when prompted to do so, you should proceed as follows: Precondition: the Maintenance indicator and the Cleaning indicator v are illuminated. v l Hold down the Cleaning button until the Cleaning indicator v flashes. The coffee grounds container indicator x now flashes. l Empty the drip tray and the coffee grounds container.
6 Maintenance Descaling the machine CAUTION The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the degree of hardness of your water. If the descaling agent comes into contact with the skin or eyes, this can cause irritation. l Avoid contact with the skin or eyes. l Rinse the descaling agent off with clean water. Should you get any descaling agent in your eye, see a doctor.
6 Maintenance The Water Tank indicator y now flashes. l Remove the water tank and empty it. l Completely dissolve the contents of one blister (3 JURA descaling tablets) in a container that holds 500 ml of water. This can take a few minutes. l Pour the solution into the empty water tank. l Insert the water tank. l Remove the frother. l Place a container under the Connector System . © r l Turn the switch in the anticlockwise direction. t 32 This causes water to flow out of the Connector System©.
6 Maintenance r l Turn the switch in the anticlockwise direction. t This causes water to flow out of the Connector System©. The operation stops automatically, and the light segment by the switch flashes. l Turn the switch in the clockwise direction. The descaling operation will resume. After a few minutes, the coffee grounds container indicator x flashes. l Empty the drip tray and the coffee grounds container. l Insert the empty drip tray and coffee grounds container back in the machine.
6 Maintenance Cleaning the Easy Cappuccino Frother To ensure that the Easy Cappuccino Frother works perfectly, you should clean it daily when you have been preparing milk. o The IMPRESSA will not prompt you to clean the Easy Cappuccino Frother. o Your dealer will stock the JURA Cappuccino Cleaner. CAUTION If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water. l Use only original JURA care products.
6 Maintenance o Perform the next step as soon as the light segment by the switch is flashing. This means that the IMPRESSA has reached the temperature necessary for steam. If the light segment is no longer flashing, turn the Rotary Switch once again to the Steam symbol k and press the Rotary Switch. As soon as the required temperature has been reached, the light segment by the switch will flash again. r l Turn the switch in the anticlockwise direction. The frother and pipe are rinsed with fresh water.
7 Messages in the maintenance field and symbol display 7 Messages in the maintenance field and symbol display Message Cause/Result Action Maintenance indicator is illuminated or is flashing. The IMPRESSA wants to tell you something. l Open the access door and note the other indicators. Maintenance indicator and Water Tank indicator y are flashing. Water tank is empty. You cannot prepare any coffee or hot water.
7 Messages in the maintenance field and symbol display Message Cause/Result Action Maintenance indicator and Descaling indicator b flash twice. System is too hot to descale. l Wait a few minutes. Maintenance symbol h flashes twice. System is too hot for maintenance and switch-off rinses. l Wait a few minutes. Maintenance indicator and all the indicators y x c v b n behind the access door are flashing synchronously. There is a general fault. l Switch the IMPRESSA off with the On/Off button G .
8 Troubleshooting 8 Troubleshooting Problem Cause/Result Action Grinder is making a very loud noise. There are some foreign bodies in the grinder. l Contact Customer Support in your The coffee grounds container indicator x is flashing continuously. Drawer with coffee grounds container has not been correctly inserted. l Insert the drawer correctly. The frother does not produce enough milk foam. Easy Cappuccino Frother is dirty. l Clean the Easy Cappuccino Frother Coffee only comes out in drips.
9 Transport and environmentally neutral disposal 9 Transport and environmentally neutral disposal Empty system To protect the IMPRESSA from damage caused by frost during transportation, the system needs to be emptied. Precondition: the IMPRESSA is ready for use. l Place a receptacle under the frother. ä l Turn the Rotary Switch so that it points to the Steam symbol k . m l Press the Rotary Switch to confirm your choice. The Steam symbol k will continue flashing until the machine has warmed up.
10 Technical data 10 Technical data Voltage 220–240 V ~, 50 Hz Power output 1450 W Marks of conformity Pump pressure Static max. 15 bar Holding capacity of water tank 1.9 litres Holding capacity of bean container 200 g Holding capacity of coffee grounds Approx. 16 portions container 40 Cable length Approx. 1.1 m Weight 9 kg Dimensions (W x H x D) 28 x 34.
Index Index A D Activate filter 13 Addresses 44 Adjusting Grinder 16 Adjusting the amount of water Descale Water tank 35 Descaling 31 E Easy Cappuccino Frother 4 One-off setting during drink preparation 19 Permanent adjusting the permanent cup size settings 20 Altering coffee strength One-off setting during drink preparation 19 Cleaning 34 Rinsing 33 Espresso preparation 21 F Filling Automatic switch-off 26 Bean container 11 Water tank 11 B Filter Bean container 4 Activating 13 Changing 28 U
Index Setting up 11 Swiching off 17 Switching on 17 Milk foam preparation 24 Water hardness 15 Assessing 15 Setting 15 Water tank 4 O One-off setting during drink preparation 19 P Pre-ground coffee preparation 22 Preparation Cappuccino 21 Coffee 21 Espresso 21 Hot water 24 Milk foam 24 Pre-ground coffee 22 Programming mode Automatic switch-off 26 Proper use 6 Putting into service First-time use 12 R Rinsing Easy Cappuccino Frother 33 Machine 27 Rotary switch 9 S Safety information 6 Setting Water
Index 43
Art. 68990/C5/en/201002 JURA contact details / Legal information JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Phone: +41 62 38 98 233 @ Contact information is available on the company website at www.jura.com. Directives The machine complies with the following EU directives: 2006/95/EC – Low Voltage Directive 2004/108/EC – Electromagnetic Compatibility 2009/125/EC – Ecodesign p p p Technical changes We reserve the right to make technical changes.
