CAPRESSO ENA 5 ENA Fully Automatic Coffee & Espresso Center Operating Instructions and Warranty Customer Service 1-800-220-5701 68191 ENA 3 ENA 4
IMPORTANT SAFEGUARDS wall outlet. To disconnect, turn any control to “off” then remove plug from wall outlet. 12. Do not use appliance for other than intended use. 13. Use extreme caution when disposing hot steam. 14. For household use only. When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3.
Notice: Your Jura ENA has a 3-prong grounded plug. To reduce the risk of electrical shock, this plug will fit in an outlet only one way. If the plug does not fit in the outlet, contact a qualified electrician. DO NOT modify the plug in any way. JURA-CAPRESSO Jura was founded in 1931 in Switzerland. Capresso was founded in 1994 in the USA. Both companies have joined forces in the US to bring you the finest Fully Automatic Coffee Centers available anywhere.
Fig. 1 1 2 15 3 4 5 6 7 8 9 10 11 14 1. Removable water tank with lid and Clearyl filter holder (Fig. 6 & 7) 2. On/Off button 3. Removable bean container lid 4. Grinder Fineness Adjustment Ring (Fig. 12 &13) 5. Cover for Programming and Rinse buttons (Fig. 4) 6. Rotary Dial with push button and illumination 7. Three-color alphanumeric display 8. Selector Switch for coffee, water, steam (Fig. 5) 9. Connector system for Dual Frother Plus and frothXpress system 10.
Coffee position To open Clearyl filter holder P button Rinse button Rotary Dial with push button ENA 5 with frothXpress Fig. 3 Fig. 4 Hot Water/ Steam position Fig. 5 Fig. 6 To close Clearyl filter holder Fig. 7 Fig. 8 5. ENA 5 ENA 5 ENA 5 1-cup position 2-cup position Rinsing position Fig. 9 Fig. 10 Fig.
Max: 2 spoons of pre-ground coffee Steaming up Frothing down Light roast: finer setting Dark roast: coarser setting Fig. 12 Fig. 13 Fig. 14 Dual Frother PLUS Steam nozzle Tip Fig. 16 Fig. 15 Fig. 17 Sleeve Rod Fig. 18 6.
Venting tip Frothing range Venting tip Milk Hose 12 to 2 o'clock Milk Hose Steam only no siphoning Steaming range 4 to 6 o'clock Chrome Nozzle MILK Fig. 19 Fig. 20 Cappuccino rinsing Fig. 21 Tablet cleaning Remove protective grinder shield with Phillips screwdriver Fig. 22 Turn Burr Grinder Release Tool slowly counter clockwise (see chapter 30) Lever Fig. 23 Fig. 24 Fig. 25 7. Fig.
Table of Contents Chapter Page Chapter Page Important Safeguards......................................................... 2 8. Daily Preparation................................................. 14 Customer Service Information ........................................... 3 9. Grinding and brewing coffee beverages............... 14 Illustrations...................................................................... 4-7 9a. Pre-warm cups...................................................... 14 1.
Table of Contents Chapter Page Chapter Page 14b. Visual programming of cup size ........................... 21 23. Keeping your machine in top shape..................... 28 15. Water care............................................................. 21 24. Cleaning the bean container................................. 28 16. Water Hardness Monitor ....................................... 21 25. Cleaning the inside of the machine ...................... 28 16.
1. PRODUCT WARRANTY REGISTRATION Please remove the Product Registration from the ENA pouch, fill it out and mail or fax it to us within two weeks after purchasing your machine or register your product online through our website: www.capresso.com. Important: This registration is part of your warranty (chapter 32). In case your retailer sent the product registration when you purchased the machine, it is not necessary to register again. a time.
machine is on you can choose between energy saving and always ready stand-by mode. High-end materials, a rich platinum metallic treatment (ENA 4 and ENA 5) and tasteful chrome accents make the ENA the highlight of any kitchen. Enjoy your JURA ENA! • Café Mocha: Add chocolate syrup to milk then steam and froth and add espresso. Experiment with the size of your milk based drinks. For stronger coffee taste add more coffee, for more milk taste add more frothed/steamed milk. 3.
Please note: You can change all above pre-sets (chapter 14a). You can also override the strengths and the cup size before/ during actual brewing. Overriding will not change the preset values (chapter 9d). • Never fill frozen beans into the bean container. If you store beans in the freezer, let them thaw 3 to 4 hours before filling them into the bean container. • Never fill anything other than coffee beans into the bean container (no chocolate, rice, nuts, spices, etc.
• machine is NOT placed on a surface which is sensitive to heat, water and steam. • Plug-in machine. enough coffee and you might get weak or no coffee at all. Before filling oily beans into the bean container pour the beans in an open bowl and let them sit for about 5 hours. The oils will evaporate (this will not change the taste of your coffee). Then fill the beans into the bean container. Now beans will feed into the burr grinder more easily.
7. ADJUSTING THE GRINDER The Grinder Fineness Adjustment Ring is set to a medium grind position. We recommend leaving the grinder in this position for most applications. Please note: You can only adjust the grinder during grinding. • If you have extremely dark roasted, oily beans, set the grinder to a coarser setting. Turn the ring counter-clockwise toward the 1-dot position (Fig. 13). • For light roasted beans turn the ring towards the 3-dot position (Fig. 12).
9b. BREWING ONE CUP If you press the Rotary Dial, the ENA will produce a 5 oz. cup of coffee in normal strength. READY, NORMAL, 1 CUP, READY ENA 5 only: If you brew one cup we recommend turning the coffee spout to the one-cup position (Fig. 9). Coffee will flow from one spout into your cup. select any of these options, the display will return to READY after approx. 7 seconds. Example: To prepare a STRONG. 2 OZ espresso. READY. • Turn the Rotary Dial to STRONG and push the Rotary Dial.
READY • Place one or two cups under the coffee spouts. • Move the small lever to the front to open the chute and insert the coffee funnel (Fig. 14). The display shows FILL PREGROUND. • Add one or two scoops of pre-ground coffee, remove the funnel and close the chute. The display shows 1 CUP *. • Press the Rotary Dial. The ENA will tamp and brew the coffee. During brewing you can change the cup size by turning the Rotary Dial. 1 CUP. READY. 12.
12a. USING THE DUAL FROTHER PLUS ENA 3 and 4 only: The Dual Frother Plus is already attached. ENA 5 only: Remove the frothXpress (Fig. 20), and attach the Dual Frother to the steam nozzle. Make sure it is pushed up completely against the steam nozzle (Fig. 17). Caution: If the Dual Frother is not attached properly or it is clogged (see chapter 12b) it is possible that the frother can be pushed off during steaming. This can cause burns and injuries.
Selector Switch to the Hot Water/Steam position (Fig. 5). Let hot water run through the frother for about 3 seconds and then stop. This will flush out any small milk droplets. Thorough cleaning of the Dual Frother parts: • Remove the Dual Frother from the Steam Nozzle (Fig. 17) and unscrew the tip from the rod (Fig. 18). Make sure the two side holes, the bottom opening and the groove in the tip are completely free of any hardened milk deposits (use hot soapy water and a cleaning brush).
Selector Switch to the coffee position. READY. • Place the cup underneath the coffee spouts and add a shot of espresso. Push the Rotary Dial. 1 CUP. Once the brewing starts change the volume to 1.5 or 2.0 oz. by turning the Rotary Dial. READY. Enjoy your Cappuccino! 13b. HOTTER MILK WITH FROTHXPRESS In order to get proper froth the milk cannot be too hot, otherwise no froth will be created with the siphoning system.
Push and hold the P button (Fig. 4) until display shows RINSE. Turn the Rotary Dial clockwise to see the following functions after RINSE: PRODUCT • reprogram cup size, strength and temperature to your liking, see chapter 14a FILTER • indicates if the Clearyl filter is installed or not; see chapters 17 to 17.4 HARDNESS • adjust the ENA to your specific water, see chapters 16 and 16.
15. WATER CARE Water is heated inside the machine, this leads to calcium deposits forming. The ENA works with: • regular tap water • bottled water • distilled water. We recommend using regular tap water or bottled water. Distilled water has no minerals and does not improve the taste of coffee. Tap water has a varying degree of water hardness (chapter 16). Most bottled water has a low level of water hardness. IMPORTANT: do not use carbonated water or any other liquid in the water tank.
• Push the Rotary Dial to confirm the setting. OK. • Push the P button. READY The machine will automatically remind you when it is time to decalcify (chapter 18.3). Please note: You can set the hardness monitor to INACTIVE. In this case you must use distilled water. strip to determine the water hardness: • Insert the strip for one second into the water you want to use. Shake off any access water and wait for one minute. One or more sections of the indicator strip will turn reddish.
READY 1. Open the cover behind the Rotary Dial. (Fig. 1,5) 2. Push and hold the P button (Fig. 4) until the display shows RINSE. 3. Turn the Rotary Dial until the display show FILTER – 4. Push the Rotary Dial. The display shows NO – 5. Turn the Rotary until the display shows YES ✓ 6. Push the Rotary dial again to confirm. The display shows OK and then INSERT FILTER 7. Remove the Clearyl cartridge from its bag and rinse cartridge under water. 8. Remove the water tank, open the Clearyl filter holder (Fig.
Since the Water Hardness Selector is off, the machine will not remind you when to decalcify. This could clog and damage your machine. 17.3 MANUAL CLEARYL REPLACEMENT If the filter is more than 2 months old and the display does not indicate to replace filter, replace as follows. READY. • Push and hold the P button until the display shows RINSE • Push the button again. The display shows again RINSE • Turn the Rotary Dial until the display shows FILTER • Push the Rotary Dial.
EMPTY TRAY. 9. Remove the cup and then the drawer and tray. 10. Empty drawer and ground coffee container and replace. 11. The display shows READY. The machine will automatically remind you after the next 180 cups of coffee to repeat this cycle. CAUTION: • Avoid contact of the descaling agent with the skin or eyes. This can cause irritation. Rinse the descaling agent off with clear, clean water. Should you get descaling agent in your eyes, consult a doctor.
4. Replace the complete assembly. 5. The display shows AGENT IN TANK. 6. Remove and empty the water tank. (The Clearyl filter should not be in the water tank!) 7. Dissolve 3 of the large square decalcifying tablets in a container with 18 oz. of water (0.5 liters) and pour the solution into the water tank and replace. 8. The display shows OPEN TAP. 9. Place a 20 oz. container under the steam nozzle (Fig. 17). 10. Turn the selector switch to the hot water/steam position. The display shows DE-SCALING.
READY. • Push and hold the P button (Fig. 4) until display shows RINSE. • Push the P button again. The display again shows RINSE. • Push the P button a third time. The display shows RINSING. After a few seconds the rinse cycle stops automatically. READY. ENA 5 only: turn the spout again to the 1- or 2-cup position. • If you use the machine all day change the setting to a larger interval, e.g. 4 hours. This way the machine is always ready to brew coffee. Changing the AUTO-OFF setting (e.g.
• • • • • RINSE. Turn the Rotary Dial until the display shows LANGUAGE Push the Rotary Dial ENGLISH Turn the Rotary Dial to ESPANOL Push the Rotary Dial to confirm: OK, IDIOMA (Language) Push the P button to leave the programming mode. LISTO (ready). 25. CLEANING THE INSIDE OF THE MACHINE • Turn off machine and let cool down for 10 minutes. • Remove the complete drawer. Wipe the inside of the machine with a paper towel. • Replace the complete drawer. 26.
water into the drawer (Fig. 1.13). This makes sure that no warm water stays in the heating system. Each cup of coffee always starts with fresh cold water. Solution: Stir the beans. When using very oily beans pour the beans onto a plate and let some of the sticky oils evaporate (this will not harm the aroma of the coffee). TRAY MISSING. The drawer is not inserted or not inserted correctly. Insert drawer correctly. Reason: You used ground coffee in the ground coffee funnel. The ground coffee was too fine.
bubbles than the frothXpress. Solution 1: Take the Dual Frother apart and make sure that all grooves and holes are free of milk deposits (Fig. 18). Solution 2: Check the steam nozzle (Fig.17). If the steam nozzle is blocked by hardened milk, use a needle, toothpick or paperclip and loosen up the milk deposit. let some hot water pass through the steam nozzle. Solution 3 (ENA 5): Clean the frothXpress, especially the small venting tip (Fig. 20, 22).
3 weeks. Always keep extra tablets available. Tip: These tablets will also remove coffee and tea discoloration and oil films in other containers (tea kettles, thermal carafes etc.) Fill container with water, add one or two tablets and let stand overnight. Rinse thoroughly). Auto-Cappuccino Cleaner (chapter 13e). One sample bottle with 100 ml included; 250 ml (approx. 8 oz) bottle: Model #63801 Tip: If you use the auto cappuccino cleaner once a day you need a new bottle (250ml) every 2 1/2 weeks.
JURA-CAPRESSO any other liability in connection with the sale of the machine. JURA-CAPRESSO expressly disclaims liability for incidental and consequential damages caused by the machine. The terms "incidental damages" refer to the loss of the original purchasers time, loss of the use of the machine or other costs relating to the care and custody of the machine.
