Wa l l C h i m n e y H o o d Instruction Manual CCH601SS / CCH601BK / CCH701 / CCH901SS / CCH901BK / CCH101 Contact Caple on 0117 938 7420 for spare parts or www.caple.co.
CONTENTS Introduction 3 Safety Instructions 4 Environmental Protection 9 Installation 10 Operation 16 Care and Maintenance 17 Troubleshooting 19 Product Dimensions 20 Caple Contact Details 24 2 Instruction manual CCH Please keep this instruction manual for future reference
INTRODUCTION Thank you for choosing this Caple extractor hood. To ensure that you get the best results from your new extractor, we strongly suggest that you read this instruction manual thoroughly before use. If treated with care, your Caple extractor should give you years of troublefree use. To register ownership, please ensure you complete and return the guarantee card supplied with the appliance or visit www.caple.co.uk and register here.
I M P O R TA N T This appliance must only be used for the purpose it is intended. Other types of use are not permitted and may prove dangerous. Caple will not be held liable for any damage caused by the incorrect use of the appliance. Do not use any accessories or attachments not recommended by Caple as this may result in fire, electric shock or injury. To protect against fire, electrical shock and injury to persons, do not immerse cords or plugs in water or any other liquid.
I M P O R TA N T Caple cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that Caple reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel. SAFETY INSTRUCTIONS - Never let children operate the machine.
- The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels. - Regulations concerning the discharge of air have to be conformed to. - Do not flambé under the cooker hood. - Never leave frying pans unattended during use as overheated fats and oils may catch fire. - To ensure the best performance, we recommend switching on the extractor 15 minutes before cooking and leave it running 15 minutes after.
- Never immerse the appliance in water. - This appliance is intended to be used in household and similar applications such as: › Staff kitchen areas in shops, offices and other working environments. › Farm Houses. › By clients in hotels, motels and other residential type environments. › Bed and breakfast type environments. - To avoid all risk, if the power cable is damaged, it must only be replaced by a Caple appointed engineer.
ELECTRICAL SHOCK HAZARD - Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer. - Failure to follow these instructions can result in death, fire, or electrical shock. - This appliance must be connected to the mains by a competent person. We recommend that the appliance is connected by a qualified electrician who is a member of the N.I.C.E.I.C who will comply with the I.E.E and local regulations.
E N V I R O N M E N TA L P R OT E C T I O N Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. This appliance is marked according to the European directive on Waste Electrical and Electronic Equipment (WEEE).
The width of the extractor hood must correspond with at least the The cooker hood should be placed at a minimum distance of 65~76cm above the hob. It is the manufacturer of the hob who determines the clearance required and the clearance quoted by the hob manufacturer must be followed. In the absence of any instructions supplied with a gas hob the minimum distance between the hob and the hood must be at least 760mm. Before installation, turn the unit off and unplug it from the outlet.
I N S TA L L AT I O N - D U C T E D RN I NG: WA the concerning Observe operation the of the appliance when air is discharged from warning room.
After hanging the hood on the bracket, remove the grease filters, mark 2 holes inside the hood for safety screws. After marking, remove the hood, drill two holes and insert 2 wall plugs and finally fix the safety screws with 2 screws (ST4x30mm). Exhaust pipe ker hood Fix the one-way-valve to the air outlet of the cooker hood.
charcoal filters must be installed. I N S TA L L AT I O N – R E C I R C U L AT I O N M O D E If you do not have an outlet to the outside, the exhaust pipe is not required (as shown in the section “Installation ducted”), and charcoal filters must be installed.
N OT E : Make sure the filter is securely locked. Otherwise, it may loosen and be dangerous. When using a charcoal filter, the extraction power may be slightly reduced. We recommend replacing these filters every 6 months. Replacement filters (CAP60CF) can be purchased directly from www.caple.co.uk.
P E R A T I O N O
CARE AND MAINTENANCE I M P O R TA N T: Before cleaning or maintenance please switch off the electricity supply and remove the plug from the wall. REGULAR CLEANING Use a soft damp cloth with lukewarm mildly soapy water or household cleaning detergent. Never use metal pads, chemicals, abrasive material, abrasive cleaning creams or stiff brushes to clean the appliance. C L E A N I N G T H E G R E A S E F I LT E R Clean the filter every month to help minimise the risk of fire.
REPLACING THE BULB N OT E : The lights must be replaced by a qualified person. 1. Switch off and unplug the extractor 2. Remove the aluminium grease filter 3. Remove the LED light by squeezing the metal clips. 4. Remove the clip cover by removing the lid (see image a.) 5. Unclip the light fixing (b.) and remove.
T R O U B L E S H O OT I N G FA U LT CAUSE SOLUTION The fan blade is jammed. The lights on, but the fan does not work The lights and fan do not work Serious vibration of the unit The extraction performance is not good The motor is damaged. Switch off the unit and contact Caple Service. To be repaired by qualified service personnel only. A blown fuse. Replace the fuse. The power cord is loose. Plug in to the power supply again. The fan blade is damaged.
PRODUCT DIMENSIONS CCH101 S I O CNC HS9 0 1 B K CCH901SS CCH701 CCH601BK CCH601SS mm 222 172 mm 373-740mm 180mm m 0m 0mm 2 90 00/ /7 600 480 mm 20 Instruction manual CCH Please keep this instruction manual for future reference 00 0/1
P l e a s e k e e p t h i s i n s t r u c t i o n ma n u a l f o r f u t u r e r e f e r e n c e Instruction manual CCH 21
N OT E S : 22 Instruction manual CCH Please keep this instruction manual for future reference
N OT E S : Please keep this instruction manual for future reference Instruction manual CCH 23
Caple Service Fourth Way Avonmouth Bristol BS11 8DW T: 0117 938 1900 E: service@caple.co.uk www.caple.co.
