AGA 13 AMP RETRO-FIT WITH AIMS (OIL TO ELECTRIC) FITTING INSTRUCTIONS LEAVE WITH CUSTOMER For use in GB and IE 02/12 EINS 515736
OIL TO ELECTRIC CONVERSION INSTRUCTIONS l ISOLATE ELECTRIC SUPPLY, OIL SUPPLY AND WATER SUPPLY (BOILER MODELS), BEFORE COMMENCING WORK. BOILER MODELS (OCB AND OEB) IMPORTANT NOTE: The boiler must be removed completely and the supply pipework either removed or suitably capped. This plumbing works need to be carried out PRIOR to the oil to electric conversion. AGA OCB MODELS (2 OVEN MODELS WITH BOILER) Isolate water supply, disconnect, drain and remove boiler completely from cooker.
DE-COMMISSION OIL SUPPLY AND REMOVE OIL CONTROLS 1. Turn off oil supply, disconnect supply to appliance (preferably outdoors) and cap off. Turn on supply and test for leaks 2. Disconnect and drain oil control valve, taking care not to spill any oil. Remove oil valve and mounting bracket from side panel. 3. Cap off oil supply pipework using fitting provided. (See Installation Sheet 1, Fig. 2). 4. Remove inner burner housing door. 5. Disconnect oil pipe to burner. Seal pipe, remove oil burner and supply pipe.
FIT STAINLESS STEEL TUNNEL 1. Fit new stainless steel tunnel (between barrel and roasting oven). 2. Replace barrel (use new graphite barrel gasket and new rope seal). (See Installation Sheet 1, Figs. 3 & 4). MODIFY INNER BURNER DOOR (FOR POST-2000 MODELS ONLY) (See Installation Sheet 3, Figs. 5 - 8). Before fitting the burner door into the sheet metal burner housing, the door has to be modified as follows: a) b) c) d) e) Remove lower fixing from pad on front of door (M5 screw).
11. Fix mains cable through cable clamp. Fix cable clamp to control panel (See Installation Sheet 4, Figs. 1 and 2). 12. Attach mains wiring to control panel. 13. Outside the appliance route mains cable through ‘P’ clips provided, and attach to hank bushes on side panel (See Installation Sheet 5, Fig. 5). 14. See ‘Electrical’ and ‘Electrical Test Procedure’ sections. PAD BELOW SIMMERING PLATE (See Installation Sheet 1, Fig. 8) 1. Remove simmering plate. 2.
ELECTRICAL WARNING: THIS APPLIANCE MUST BE EARTHED. THIS APPLIANCE IS DESIGNED FOR THE VOLTAGE STATED ON THE RATING PLATE, WHICH IS SITUATED ON THE TOP OF THE CONTROL BACK COVER. A 13 amp 230v ~ 50 Hz fused electrical supply is required adjacent to the appliance. External wiring to the unit must be installed using a 3 core silicon - SIHF insulation cable, and in accordance with the current wiring regulations and any local regulations which apply.
INSTALLATION SHEET 1 FIG. 1 OIL CONTROLS TO BE REMOVED FIG. 2 CAP OFF OIL SUPPLY FIG. 3 FIT NEW ROPE SEAL FIG. 4 FIT TUNNEL BETWEEN BARREL & OVEN FIG. 5 PLATFORM AND PADS INTO ASHPIT FIG. 6 POSITION TAILS THROUGH SLOT IN PLATFORM FIG. 7 POSITION ELEMENT FIG.
INSTALLATION SHEET 2 PRE- 2000 MODELS ONLY (CAST BURNER HOUSING) FIG. 1 DRILL AND TAP HOLE (M6) FIG. 2 OPEN OUT HOLE INTO OVEN FIG. 3 MODIFY HOLE FOR FLEX CONDUIT FITTING FIG. 4 FIT LOCATION BRACKET TO TOP OVEN FIG. 5 USE LONGER FIXINGS FIG. 6 STUDS PROTRUDING THROUGH ROOF OF OVEN FIG. 7 POSITION ELEMENT AND OVERHEAT SENSOR 10mm SPACING FIG.
INSTALLATION SHEET 3 BURNER DOOR FITTING (CAST IRON HOUSING) FIG. 1 FIG. 3 FIG. 2 FIT INSULATION BLANKET FIXINGS FOR CONTROL BACK COVER FIG. 4 BURNER DOOR FITTING (SHEET METAL HOUSING) FIG. 5 M5 STUD FITTED TO BURNER DOOR FIG. 6 FIXINGS FOR CONTROL BACK COVER (M5) NUTS, WASHERS PLUS 2 SCREWS FIG. 7 FIG.
INSTALLATION SHEET 4 FIG. 1 REMOVE CABLE CLAMP. ATTACH MAINS CABLE FIG. 2 FIX CABLE CLAMP TO CONTROLS PANEL FIG. 3 ROUTE THERMOCOUPLE THROUGH NOTCH FIG. 4 REMOVE FRONT FIXING FIG. 5 POSITION AND FIRE CLAY IN PLACE FIG. 6 SILICONE MESH ONTO SHROUD FIG.
INSTALLATION SHEET 5 FIG. 1 POST 2000 STAT PHIAL SUPPORT BRACKET PRE 2000 STAT PHIAL FIG. 2A POSITION THEROCOUPLE (10mm SPACING) SUPPORT BRACKET FIG. 2B FIG. 3 REVERSE INSTRUCTION PLATE FIG. 4 DATA PLATE POSITION FIG. 5 ROUTE CABLE USE ‘P’ CLIP AND GROMMET FIG. 6 DRILL 2 HOLES (AS SHOWN) FIG.
For further advice or information please contact your local distributor/stockist With AGA-Rangemaster’s policy of continuous product improvement, the Company reserves the right to change specifications and make modifications to the appliance described at any time. Manufactured by AGA-Rangemaster Station Road Ketley Telford Shropshire TF1 5AQ England www.agaliving.com www.agacookshop.co.
