Specifications

ManualsBrandsCaple ManualsHobC806C

123

FIBER

SENSORS

LASER

SENSORS

PHOTOELECTRIC

SENSORS

MICRO

PHOTOELECTRIC

SENSORS

AREA

SENSORS

SAFETY

COMPONENTS

PRESSURE

SENSORS

INDUCTIVE

PROXIMITY

SENSORS

PARTICULAR

USE SENSORS

SENSOR

OPTIONS

WIRE-SAVING

SYSTEMS

MEASUREMENT

SENSORS

STATIC CONTROL

DEVICES

LASER

MARKERS

Selection

Guide

Fiber Sensor

Amplifiers

FX-300

FX-100

Fibers

FT / FD / FR

FX-410

FX-311

FX-11A

FX-301-F

Other

Products

FIBER

SENSORS

FX-100

Fiber Sensor

Ampliﬁ ers

Related Information

Digital Fiber Sensor

FX-100 SERIES

Glossary of terms / General precautions ...

P.983~ / P.986~

■

Taking ﬁ ber sensors to the next level

Conforming to

EMC Directive

The dual digital display allows users to check both the threshold

value and incident light intensity at the same time, allowing

for clear and intuitive control of the sensor’s functions. The

threshold value can be adjusted simply by pressing the

(UP)

key or the (DOWN) key, so that the output operation can be

controlled with high precision, directly from the RUN mode.

Setup is made simple, using a dual digital display

Commercially-available connectors are used so that lead time and spare part numbers

can both be reduced

The connectors used are commercially-available connectors,

so that processing costs and lead time required for carrying

out processing after purchase of the sensors can be greatly

reduced. The same connection parts as the DP-100 series

of digital pressure sensors and the PM-64 series of micro

photoelectric sensors can be used.

Fiber selection

................................. P.63~■

General terms and conditions ............. P.1■

Sensor selection guide

........P.11~ / P.61~■

PNP output

type available

Timer

Light intensity

monitor

Interference

prevention

utomatic

sensitivity setting

Test input

Conventional (cable type)

From now on (built-in connector type)

Using cables with connectors

1 Sensor purchase and preparation

2 Harness processing by outside order

1 Sensor purchase and preparation

2 Harness processing by outside order

Purchase of sensors and cable with connectors

Conventional lead time

Customer

Harness

processor

Customer

Harness

processor

Sensor preparation

Harness Processing

Sensor installation

Reduced

Sensor installation

Reduced

Sensor preparation

Sensor installation

Lead time from now on

Lead time further reduced

Reduced

lead time

●

Harness processing by outside order after sensor preparation

●

Harness processing by outside order

Commercially-available press-ﬁ t connectors are used, so that the processing

costs for connection cables can be greatly reduced.

Threshold value Incident light intensity

Connection with a

commercially-available

connector

http://www.sunx.com

SUNX website

Summary of content (16 pages)

PAGE 1
23 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES Related Information ■ General terms and conditions............. P.1 ■ Glossary of terms / General precautions...P.983~ / P.986~ ■ Sensor selection guide........P.11~ / P.61~ ■ Fiber selection................................. P.
PAGE 2
Digital Fiber Sensor FX-100 SERIES ORDER GUIDE LIST OF FIBERS SPECIFICATIONS I/O CIRCUIT DIAGRAMS SENSING CHARACTERISTICS PRECAUTIONS FOR PROPER USE DIMENSIONS P.126~ P.128~ P.133 P.134~ P.135~ P.136~ P.138 Saving-space with a width of 9 mm 0.354 in Equipped with a four-chemical emitting element The sensor is very slim, yet equipped with a dual digital display. Both space saving and ease of use have been achieved.
PAGE 3
125 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Digital Fiber Sensor FX-100 SERIES Teaching using ON / OFF buttons [SET mode] Attenuation function [SET mode] Simply press the ON button when an object is present and OFF when it is not. There is no need to switch settings or make judgments between Light-ON ( ) and Dark-ON ( ).
PAGE 4
Digital Fiber Sensor FX-100 SERIES ORDER GUIDE FIBER SENSORS Amplifiers Appearance M8 plug-in connector type Cable set (Note 1) Standard type M8 plug-in connector type Type M8 plug-in connector type M8 plug-in connector type Cable set (Note 1) LASER SENSORS Accessory Emitting element Model No.
PAGE 5
127 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS LASER SENSORS Thru-beam type (one pair set) PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to p.63~ “Fiber Selection” for details of each fiber. AREA SENSORS FT-A8 Model No.
PAGE 6
Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS 128 FIBER SENSORS Retroreflective type LASER SENSORS Fibers are listed in alphabetic order. Refer to p.63~ “Fiber Selection” for details of each fiber. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Model No. FR-KV1 Sensing range (mm in) (Note 1, 2) Standard type FX-101□ Long sensing range type FX-102□ Dimensions 15 to 200 0.591 to 7.874 15 to 360 0.591 to 14.173 P.112 FR-KZ21 200 7.874 200 7.874 P.112 FR-KZ21E 200 7.874 200 7.874 P.
PAGE 7
129 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS LASER SENSORS Reflective type PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to “Fiber Selection p.63~” for details of each fiber.
PAGE 8
Digital Fiber Sensor FX-100 SERIES 130 FIBER OPTIONS FIBER SENSORS Lens (For thru-beam type fiber) Designation The dimensions are on p.120~. Model No. Description Sensing range (mm in) [Lens on both sides] Fiber Increases the sensing range by 5 times or more. Expansion lens (Note 1) FX-LE1 • Ambient temperature: –60 to +350 °C –76 to +662 °F (Note 3) Amplifier FX-101□ FX-102□ FT-B8 2,200 86.614 3,500 137.795 (Note 2) FT-FM2, FT-T80 3,000 118.110 3,500 137.795 (Note 2) FT-R80 1,900 74.
PAGE 9
131 Digital Fiber Sensor FIBER OPTIONS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS FX-100 SERIES Lens (For reflective type fiber) Designation Pinpoint spot lens AREA SENSORS The dimensions are on p.121~. Model No. Description Pinpoint spot of ø0.5 mm ø0.020 in. Enables detection of minute objects or small marks. • Distance to focal point: 6 ± 1 mm 0.236 ± 0.
PAGE 10
Digital Fiber Sensor SPECIFICATIONS Standard type Model No. Long sensing range type Cable set Cable set NPN output FX-101(-Z) (Note 4) FX-101-CC2 PNP output FX-101P(-Z) (Note 4) FX-101P-CC2 Supply voltage Power consumption Output 12 to 24 V DC ± 10 % NPN non-contact input • Signal condition High: +8 V to +V DC or Open Low: 0 to +2 V DC (Source current 0.5 mA or less) • Input impedance: 10 kΩ approx.
PAGE 11
133 Digital Fiber Sensor I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS FX-10□(-Z/-CC2) NPN output type I/O circuit diagram Terminal arrangement diagram Color code of cable with connector 1 Sensor circuit PRESSURE SENSORS 2 Tr +8 V (Black) Output Load + – 100 mA max. ZD 3 4 INDUCTIVE PROXIMITY SENSORS WIRESAVING SYSTEMS Terminal No. (Brown) +V D SAFETY COMPONENTS SENSOR OPTIONS Connector type Terminal No.
PAGE 12
SENSING CHARACTERISTICS (TYPICAL) FT-A8 • Horizontal direction FT-B8 FT-FM2 FT-FM2S FT-FM2S4 Thru-beam type FT-SFM2 FT-T80 Thru-beam type Parallel deviation Parallel deviation 1,000 39.370 3,000 118.11 2,000 78.74 FX-101 Fiber head 1,000 39.37 ℓ 8 mm 0.315 in approx. L 2,000 78.74 Fiber head ℓ 1,000 39.37 L 1,000 39.370 FX-102 FX-101 Fiber head 500 19.685 ℓ L Fiber head Fiber head Fiber head 0 200 100 0 100 200 7.874 3.937 3.937 7.
PAGE 13
5 Digital Fiber Sensor PRECAUTIONS FOR PROPER USE FIBER SENSORS LASER SENSORS AREA SENSORS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Using in combination with the FX-300 / FX-400 series • The FX-100 series does not use the horizontal connectors that are used with the FX-300 / FX-400 series. Please note that horizontal connection cannot be performed using a connector attached cable.
PAGE 14
Digital Fiber Sensor PRECAUTIONS FOR PROPER USE • PRO mode appears after the MODE key is pressed for 4 sec. in RUN mode. Shift setting External input setting Threshold value follow-up cycle setting (Note 1) GETA function setting (Note 2, 3) ECO setting Digital display inversion setting Threshold value margin setting Setting copy Reset Setting copy function • This can copy the settings of the master side amplifier to the slave side amplifier.
PAGE 15
137 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Selection Guide Fibers FT / FD / FR Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products Digital Fiber Sensor FX-100 SERIES PRECAUTIONS FOR PROPER USE Refer to p.
PAGE 16
Digital Fiber Sensor FX-102□ Amplifier 47 1.850 29 1.142 20 12.2 0.787 0.480 0.8 0.031 FX-101(P)-Z FX-102(P)-Z 6 0.236 6 0.236 2.7 0.106 0.7 0.028 Amplifier 0.7 0.028 MODE key Operation indicator (Orange) 4.1 0.161 Digital display (Green, Red) 2.7 0.106 OFF key / Setting value DOWN key ON key / Setting value UP key MODE key 9 0.354 9 0.354 1 0.039 7 0.276 1.1 0.043 3 0.118 10 30 0.3941.181 4 0.157 10 0.394 8.1 0.319 ø3.2 ø0.126 50 1.969 13.5 35 1.378 0.531 64.5 2.539 ø6.5 ø0.