Rise & Shine Alarm Clock Dock with Lightning connector and with USB* charging & audio Ci210 user guide
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Rating Label is located at the bottom enclosure of the unit.
IMPORTANT SAFETY PRECAUTIONS INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SAFETY PRECAUTIONS a. Do not expose this unit or the AC/DC adaptor to dripping or splashing water. Keep liquid-filled objects such as vases, away from this unit and AC/DC adaptor. b. Unplug this unit during lightning storms or when unused for long periods of time. c. Ensure that the AC/DC adaptor is easily accessible. d. Please note the information printed underneath the unit. e. Batteries should not be exposed to excessive heat such as direct sunshine, fire, etc. f.
inside the box Ci210 alarm clock dock, AC/DC power adapter and user guide. AC/DC adapter connection AC outlet Insert the small end of the AC adaptor into the DC IN Jack (located on the rear of the unit). Connect the other end to a wall outlet providing 100-240V AC, 50/60 Hz. notes: Disconnect both the DC IN plug and the AC plug when not in use.
inserting batteries Two (2) ‘AAA’ size batteries (sold separately) can be used to backup the clock and keep up the memory of the alarm setting if the AC adaptor is disconnected or there is a power failure. Install as listed below: Open the battery door by pushing in on the tab, then removing the door. Insert two (2) 1.5V ‘AAA’ batteries as shown. Alkaline batteries are recommended for the longest backup time. Replace the battery door back on the compartment.
location of controls Dock with Lightning connector POWER Button SOURCE Button TUNING DOWN / SKIP / SEARCH Button PLAY / PAUSE / PRESET Button TUNING UP / SKIP / SEARCH Button TIME SET / TIME SYNC Button SNOOZE / SLEEP Button Top Cover Left Speaker 1 VOLUME + / BRIGHTNESS UP Button VOLUME – / BRIGHTNESS DOWN Button 2 3 4 5 6 7 8 9 LCD Display Battery Compartment (bottom) ALARM 2 Button ALARM 1 Button Right Speaker 10 11 12 13 14 15 16 17
location of controls (con’t.) DC Power In Jack 3.
turning the unit on Press the POWER button to turn the unit on. Press the POWER button again to turn the unit off. notes: In standby mode, the clock time will show as the display. When you turn on the unit again, it activates on the same source mode as the last time you turning off the unit. For power saving, the unit switches to standby mode if no audio signal for 15 minutes. adjusting the volume Press the VOL + or VOL – button repeatedly to increase or decrease the volume respectively.
iPod or iPhone playback (docking mode) Place your iPod or iPhone onto the dock. Gently push down so the connector on the iPod or iPhone slides onto the Lightning connector of the unit. The unit will switch to Docking mode automatically. You can also press the SOURCE button repeatedly to select Docking mode. Press the PLAY / PAUSE / PRESET button to start music playback from your docked iPod or iPhone. Press the PLAY / PAUSE / PRESET button again to pause and once more to resume playback.
iPod or iPhone playback (USB mode) You can play or charge your iPod or iPhone through the USB input at the unit back with an Apple USB cable (sold separately). Connect an Apple USB cable from the USB input on the back of the Ci210 to the dock connector on your iPod or iPhone Press the SOURCE button repeatedly to select USB audio mode. Press the PLAY / PAUSE / PRESET button to start music playback from your USB connected iPod or iPhone.
universal USB charging port This unit can charge smart phones, tablets, Android and USB devices when connected with a charging cable (sold separately) through the USB port located on the back of the unit. The unit charges the devices automatically as long as it is connected to a power source. using the FM radio Press the SOURCE button repeatedly to select Radio mode. In RADIO MODE, you can tune radio stations manually or automatically.
setting radio presets You can save up to 10 of your favorite radio stations as presets for easy station recall. In RADIO MODE, follow the steps from the ‘using the FM radio’ section above to tune a desired radio station. Press and hold the PLAY / PAUSE / PRESET button to activate PRESET SAVE MODE. (01-10) blinks on the display. Press the TUNING DOWN / SKIP / SEARCH or TUNING UP / SKIP / SEARCH button repeatedly to select the desired preset number you wish to save that station as.
setting the alarm(s) Press and hold ALARM 1 or ALARM 2 button to enter ALARM SETTING MODE. (The ‘HOUR’ digits will begin to blink on display) Repeatedly press the TUNING DOWN / SKIP / SEARCH or TUNING UP / SKIP / SEARCH buttons to set the hour. Press the ALARM 1 or ALARM 2 button to confirm. (The ‘MINUTE’ digits will begin to blink on display). Repeat steps 2 – 3 to set the minute. (The ‘ALARM VOLUME’ digits begin to blink). Press VOL + or VOL – buttons to set the alarm volume level.
activate / deactivate the alarm(s) Press ALARM 1 or ALARM 2 button repeatedly. The corresponding alarm icon will appear on the display when the alarm is activated. The corresponding alarm icon disappears when the alarm is deactivated. turning off / snooze alarm To TURN OFF the alarm when it sounds, press ANY button (except SNOOZE / SLEEP) one time. The alarm will reset for the next day. To SNOOZE the alarm when it sounds, press the SNOOZE / SLEEP button once.
sleep timer To TURN ON the SLEEP Timer, press and hold SNOOZE / SLEEP button to activate the sleep timer function. This will activate a SLEEP Timer period of 10 minutes, at which time the unit will enter standby mode. To TURN OFF the SLEEP Timer function, press and hold the SNOOZE / SLEEP button once and then repeatedly press this button until the 'SLEEP' icon no longer appears on the display.
time sync The Ci210 features ‘Time Sync’ which will automatically set the time when an iPod or iPhone is docked with the unit. Press the SOURCE button repeatedly to switch to Docking mode or USB mode Connect your iPod or iPhone to the unit Press and hold the TIME SET / TIME SYNC button. The clock digits and the “SYNC” icon blinking on the display, then the clock time updates to the unit automatically.
aux-in connection Insert one end of a 3.5mm audio cable (sold separately) into the LINE IN jack on the rear of this unit and the other end into the headphone jack of an external audio device (e.g. iPad, iPod shuffle, smart phones, MP3 players, digital media players, etc.) Press the SOURCE button repeatedly to select AUX-IN mode. In AUX-IN MODE, press the play button on your external audio device to begin playback through the unit’s speakers. specifications Power Source ...............................
? troubleshooting If you experience a problem with this unit, please check the chart below before calling for service. symptom cause solution No Sound Volume is set to minimum Increase volume Radio, no sound. Power is not on Press the power button to turn the power on Volume is set to minimum Increase volume Station is not tuned properly Retune the FM broadcast station FM: Wire antenna is not extended Extend FM wire antenna Radio, poor sound. iPod mode, no sound.
For further assistance, please visit our website: hellocapello.com or contact customer service at support@capelloproducts.com or 1-855-896-1795 Life Lab International Ltd.