User Manual

A
1
Fixture
B
3
Glass Shade
C 9 Fixture Screw
1
3 Strip 3/4" (19 mm) of insulation from fixture wire ends.
Twist stripped ends together with pliers (not included),
black to black (power), white to white (neutral). Snip
ends. Wrap the ground wire from the outlet box
around the green screw on the mounting plate (AA),
and then connect the ground wire from the outlet
box to the ground wire from the fixture.
Attach wire nuts (DD) to ends. Tape wire nuts (DD)
and wires together with electrical tape (not included).
A
B
C
5.
5
Attach glass shades (B), and secure with previously
removed fixture screws (C).
4
4.
C
C
A
B
6
Unscrew the fixture screws (C) from fixture (A).
Save for later use.
Install the bulbs. Use three 60 W (max.)
medium-base incandescent bulbs or equivalent
CFLs (not included).
6.
BB
AA
A
BB
AA
A
3-LIGHT VANITY FIXTURE
MODEL NO. 052-7884-0
2
Package and Hardware Contents 2
Important Safety Instructions 3
Assembly Preparation 3
Assembly Instructions
4
6
Warranty 6
Table of Contents
Package and Hardware Contents
3
Important Safety Instructions
Assembly Preparation
4
MODEL NO. 052-7884-0 MODEL NO. 052-7884-0
Assembly Instructions
5
Assembly Instructions
6
Warranty
PART
DESCRIPTION QUANTITY
Place fixture (A) over mounting plate (AA),
securing with previously removed mounting
screws (BB).
This CANVAS product carries a one (1) year warranty against defects in workmanship
and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated
warranty period, when returned by the original purchaser with proof of purchase.
This product is not guaranteed against wear or breakage due to misuse and/or abuse.
™
IMPORTANT: Please read this manual carefully before attempting to assemble, operate or
install the product, and save it for reference.
Care and Maintenance/Troubleshooting
DDCC
BBAA
Mounting Screw
Qty. 2
Mounting Plate
Qty. 1
Wire Nut
Qty. 2
Outlet
Box Screw
Qty. 2
CAUTION
The following rules must be adhered to when assembling the product. If you have any
doubts about how to install the product or if it fails to work properly, contact a local,
licensed electrician. Failure to comply with these requirements could lead to an electric
shock or fire, which could cause serious injury or fatality.
Power at the main fuse box is disconnected before installing the fixture.
The fixture ground wire (bare or green insulated wire) is NOT connected to current-carrying
wires.
No bare wires are exposed outside the wire connectors when joining current- carrying
wires.
The insulation on wires has not been damaged during installation.
No rough or sharp edges are in contact with any of the wires.
Fixture wires are connected to the proper house supply wires. If you have any doubts
about which house supply wire is white and which is black, contact a licensed electrician.
Light bulbs with wattage no greater than those specified for the fixture are used.
Power is off when installing light bulbs into the fixture.
Ensure:
Tools required for assembly (not included):
Before beginning assembly of this product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble, install or operate the product.
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove
all packing materials and place them back into the box. Do not dispose of the packing materials until
assembly is complete. Read each step carefully before beginning any assembly and make sure you
understand each step.
Flat-head screwdriver, cross-head screwdriver, electrical tape, safety glasses, ladder, wire
strippers, pliers.
CARE AND MAINTENANCE
. Shut off main power before cleaning light with damp cloth or window cleaner.
Do not use abrasive cleansers.
. Bulb replacement: Use three 60 W medium-base bulb or equivalent CFLs.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Bulbs won't light.
Fuse blows out or
circuit breaker trips
when light is turned on.
1. Bulbs are burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.
1. Replace the bulb.
2. Check if power supply is on.
3. Check wiring.
4. Test or replace the switch.
1a. Check the wiring connection.
1b. Consult a qualified electrician.
1.
Crossed wires or power
wire is grounding out.
Made in China
Imported by
Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Care and Maintenance/Troubleshooting
1. Unscrew the mounting screws (BB) from fixture (A).
Save for later use. Separate the mounting plate (AA)
from backplate of fixture (A).
AA
CC
2
Attach the mounting plate (AA) to outlet box (not
included) using outlet box screws (CC).
2.
AA
3
ASSEMBLY INSTRUCTIONS
DD