SUMMERHILL MOTION CHAIR PRODUCT NO. 088-2036-6 ASSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
Made in Vietnam Imported for Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Important Safety Instructions 3 Parts List 4 Assembly 5 Cleaning and Maintenance 8 Technical Data 8 Warranty 9 TABLE OF CONTENTS 3 Caution! Always keep children under close supervision while they are using or are around this product. Never leave children unattended. • • • • • • • • • • • • This product is intended for domestic outdoor use only. The product should be placed on flat, horizontal ground. Any assembly or maintenance of the product must be carried out by adults only.
PARTS LIST 4 PRODUCT NO. 088-2036-6 1 A Seat Assembly - 1 M6x35 mm Bolt - 1 2 B Support Frame - 1 M8x30 mm Bolt - 8 3 C Swing Bar - 2 M8x40 mm Bolt - 4 4 D Seat Post - 1 d6.5xD30x2.0 mm Washer - 1 5 E Base Assembly - 1 d8.5xD17x1.6 mm Washer - 4 6 F Back Cushion - 1 d8.5xD12.5x1.5 mm Washer 24 7 G Seat Cushion - 1 d8.5xD12x2.1 mm Washer 4 H M8x1.
• • • • • • CAUTION! Proper placement of your chair is essential. Do not place the product underneath electrical lines. Keep children away during assembly. This product contains small parts which can be swallowed by children. Keep fingers away from the places where they can be pinched or trapped. Do not attempt to assemble the chair if any parts are missing. Let us help you! DO NOT RETURN YOUR PRODUCT TO THE STORE.
PRODUCT NO. 088-2036-6 ASSEMBLY Step 1 Requires: 1, 2, 3, B, and F Turn the swivel rocker chair upside down, fasten the support frame 2 to the seat assembly 1 and the swing bars 3 by using bolts B and washers F. Make sure that all of the bolts have been tightened completely. B F 3 2 F F F 3 F F F B B 1 Step 2 Requires: 2, 4, C, E, G, and H Place the seat post 4 onto the brace of the support frame 2. Fasten them together by using bolts C, washers (E and G), and jam nuts H.
Insert the seat post 4 into the hole in the centre of the base assembly 5. Fasten them together by using bolt A and washer D. Make sure that all of the bolts have been tightened completely. Secure all of the bolts by using wrenches Ⅰ, Ⅱ, Ⅲ, and Ⅳ. Note: For ease with installation, we recommend that the seat post 4 be lightly oiled or waxed before fastening it to the base assembly 5. A D Ⅰ Ⅲ Ⅱ Ⅳ 4 5 D A Step 4 Requires: 6 and 7 Place cushions (6 and 7) onto the chair.
CLEANING AND MAINTENANCE TECHNICAL DATA 8 PRODUCT NO. 088-2036-6 CAUTION! • Check all of the bolts and nuts periodically for tightness, fastening them again as required. • Disassemble the chair in the reverse order of the assembly steps. Always disassemble • the chair completely. A partially disassembled chair is not stable enough to resist wind and bad weather, and therefore can be damaged and/or cause damage. Clean the chair with mild soap and water.
This Canvas product carries a five (5) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase.This product is not guaranteed against breakage due to misuse and/or abuse.
