OCTAVIA GAZEBO MODEL N0. 088-0741-8 ASSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
3 Important Safety Instructions 3 Parts List 5 Assembly 7 Maintenance 19 19 Warranty 20 WARNING! To reduce the risk of serious injury, read the following safety instructions before assembling and using the gazebo. CAUTION! • Always keep children under close supervision while they are playing near the gazebo. Never leave children unattended. Keep pets away while setting up the gazebo. • Check municipal by-laws prior to setting up the gazebo.
4 5 MODEL NO. 088-0741-8 • Some parts may contain sharp edges. Wear protective gloves if necessary. IMPORTANT SAFETY INSTRUCTIONS • A1 Post 1 - 4 • The gazebo is not designed to withstand harsh weather, including high winds, rain and snow. Always remove the gazebo in such heavy weather conditions; otherwise it might tip over and cause damage to the product or injuries to bystanders.
P3 Panel for big roof 2 - 8 PARTS LIST 7 PRODUCT NO.
9 PRODUCT NO. 088-0741-8 NOTE: NOTE: ASSEMBLY between the frame and the screw and/or nut. This will protect the parts from wear and tear. Step 1 Requires A1, A2, B, AA, BB, W Arrange all posts (A1, A2) in an alternate manner. Attach the top base (B) to the the wrench (W). Repeat the same procedure for the other top bases. BB AA • Make sure the side panels are assembled in an alternate manner such that the side panels 1 (L1) face each other and side panels 2 (L2) face each other.
11 PRODUCT NO. 088-0741-8 Step 7 Requires E, G, BB, DD, EE Step 5 Requires B, D, BB, DD, EE ASSEMBLY Attach the lower end of the slanting bar (D) to the U-shaped channel of the top base (B) using the screw (DD), flat washer (BB) and nut (EE). BB DD EE Attach the upper end of the horizontal portion of the slanting bar for small roof (E) to the U-shaped channel of the connector for small roof (G) using the screw (DD), flat washer (BB) and nut (EE).
13 PRODUCT NO. 088-0741-8 Step 9 Requires D, H1, H2, H3, AA, BB, W ASSEMBLY Attach the beams (H1, H2, H3) between the adjacent slanting bars (D) one by one from top to bottom using the bolt (AA) and flat washer (BB). Tighten the bolt using the wrench (W). H1 H2 H1 H2 H2 Attach the lower tube (I) to the protruded tip of the slanting bar (D) using the bolt (AA) and flat washer (BB). Tighten the bolt using the wrench (W).
15 PRODUCT NO. 088-0741-8 Step 15 Requires P2, P3, P4, P5, BB, FF Step 13 Requires J1, BB, GG ASSEMBLY Place the small top roof cover (J1) onto the edges of the assembled panels and attach using the screw (GG) and flat washer (BB). BB Attach the big roof panels (P2, P3, P4, P5) one by one from top to bottom in order, using the screw (FF) and flat washer (BB).
17 PRODUCT NO. 088-0741-8 Step 16 Requires J2, BB, GG Step 18 Requires M, N, AA, BB, W Attach the big top roof cover (J2) to the big roof panels using the screw (GG) and flat washer (BB). Attach the tile top (M) to the support for tile top (N) on both sides using the bolt (AA) and flat washer (BB). Tighten the bolt using the wrench (W).
19 PRODUCT NO. 088-0741-8 Step 20 Requires L1, O, AA, BB, W ASSEMBLY Attach the other end of the connector for tile top (O) to the corresponding hole at centre the bolt using the wrench (W). AA BB W • Check all bolts, screws, and nuts periodically for tightness. If required, tighten them. • If required to disassemble the product, follow the assembly steps in the reverse order.
20 PRODUCT NO. 088-0741-8 WARRANTY This CANVAS product carries a three (3) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace a defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
