DASHLEY COLLECTION GAZEBO MODEL NO. 088-1760-6 ASSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.
MADE IN CHINA IMPORTED BY TRILEAF DISTRIBUTION TRIFEUIL TORONTO, CANADA M4S 2B8
Table of contents 3 Important safety instructions 3 Parts list 4 General requirements 7 Assembly 8 Cleaning and maintenance 28 Specifications 28 Warranty 29 TABLE OF CONTENTS 3 Caution! Always keep children under close supervision while they are playing around this product. Never leave children unattended. Keep pets away while setting up the gazebo. Caution! Check municipal by-laws prior to installing the gazebo. • This product is intended for domestic outdoor use only.
PARTS LIST 4 PRODUCT NO.
Big top cover for slanting bar - 4 O Connector for small top - 1 P Hook - 1 Q Wall - 1 Q1 Small roof cover (long side) - 2 Q2 W1 Small top roof panel (short side) - 2 W2 Small top roof panel (long side) - 2 X1 Big cover (long side) - 2 X2 Big top roof left big panel - 4 X3 Big top roof right big panel 2- 4 X4 Small roof cover (short side) - 2 Big top roof left middle panel - 4 R X5 Mosquito netting - 1 Big top roof right middle panel - 4 R1 Big roof left cover - 4 R2 Big roof right cov
PRODUCT NO. 088-1760-6 AA AA M6X15 bolt - 80* M6X15 bolt - 4 BB M6 washer - 378* PARTS LIST Spare Parts List CC BB M6 washer - 19 CC M6X15 screw - 160* M6X15 screw - 8 DD DD M6X25 screw - 16 M6X25 screw - 2 EE M6X45 bolt - 64 FF EE M6X45 bolt - 2 FF M6X55 screw - 28 M6X55 screw - 1 GG GG M6 nut - 28 M6 nut - 1 HH HH M6X40 screw - 18 M6X40 screw - 1 II JJ Ф8X260 stake - 16 JJ Ring - 104 Z M6 wrench - 2 * Cumulative numbers of the hardware are listed in the manual.
CAUTION! • Proper placement of the gazebo is essential. Do not place the product underneath electrical lines. • Keep children under close supervision while they are playing around this product. This product contains small parts which can be swallowed by children. • Keep fingers away from places where they can be pinched or trapped. • Do not attempt to assemble the gazebo if any part is missing. • Do not light any fires inside or near the product! • Stay calm if fire breaks out. Search for the nearest exit.
PRODUCT NO. 088-1760-6 NOTE: ASSEMBLY When using screws and nuts to assemble the product, always use a flat washer between the frame and the screws and/or nuts. This will protect the parts from wear and tear. Step 1 Requires A, B, C, BB, CC (1a) Insert Post (A) into Base cover (C). A C (1b) Attach Base (B) to the bottom of Post (A) using M6x15 screw (CC) and M6 washer (BB). Repeat the same procedure for the other bases.
Step 2 Requires D1, D2, T, BB, CC ASSEMBLY Slide the Cutting sleeve (T) into the centre of each Beam for long side (D1) and each Beam for short side (D2). Attach in the centre aligning the outer holes using M6x15 screws (CC) and M6 washers (BB). CC BB CC CC BB BB T T D1 D2 D1 D2 Step 3 Requires A, D1, D2, BB, EE, Z Attach Beam for long side (D1) and Beam for short side (D2) to Posts (A) using M6x45 bolts (EE) and M6 washers (BB). Tighten the bolts using the wrench (Z).
PRODUCT NO. 088-1760-6 Step 4 Requires A, H1, BB, DD ASSEMBLY Attach each Lower beam connector 1 (H1) to the top of each Post (A) using M6x25 screws (DD) and M6 washers (BB). BB DD DD DD DD DD H1 A D2 D1 Step 5 Requires E1, E2, E3, AA, BB, Z Insert Decorative groove for long side (E1) and Decorative groove for short side (E2) into each Decorative groove for corner (E3) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z).
Align the holes of the assembled Decorative grooves (E3) with the holes of the Lower beam connector 1s (H1). Attach the Decorative groove (E3) in all four corners to the Lower beam connector 1s (H1) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z). AA BB Z E3 H1 BB D1 BB AA AA D2 Step 7 Requires D1, D2, I, AA, BB, Z Attach the Lower middle beam connectors (I) to beams (D1, D2) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z).
PRODUCT NO. 088-1760-6 Step 8 Requires A, V, D1, D2, BB, EE ASSEMBLY Attach the lower end of Arc supports (V) to Posts (A) and upper end of Arc supports (V) to beams (D1, D2) using M6x45 bolts (EE) and M6 washers (BB). BB EE Z D1 D2 A V BB EE Step 9 Requires J1, J2, AA, BB, Z Attach Frame for short side under big roofs (J2) to Frame for long side under big roofs (J1) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z).
Step 10 Requires H2, J1, J2, AA, BB, Z AA BB ASSEMBLY Attach Lower beam connector 2s (H2) to Frame for long and small side under big roofs (J1, J2) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z). Z AA H2 BB J1 J2 Step 11 Requires F2, O, BB, FF, GG Attach one end of each Slanting bar for small roof (F2) to the Connector for small top (O) using M6x55 screws (FF), M6 washers (BB) and M6 nuts (GG).
PRODUCT NO. 088-1760-6 Step 12 Requires F2, H2, BB, FF, GG ASSEMBLY Attach Slanting bar for small roofs (F2) to lower beam connector 2s (H2) using M6x55 screws (FF), M6 washers (BB) and M6 nuts (GG). BB FF GG FF BB GG BB H2 F2 Step 13 Requires F2, K1, K2, BB, CC Attach Small roof top beams (K1, K2) to Slanting bar for small tops (F2) using M6x15 screws (CC) and M6 washers (BB).
Step 14 Requires O, P O P Step 15 Requires F1, H1, BB, FF, GG Attach one end of Slanting bar for large roof (F1) to Lower beam connector 1 (H1) using M6x55 screws (FF), M6 washers (BB) and M6 nuts (GG). BB FF GG F1 FF BB H1 GG BB ASSEMBLY Attach Hook (P) to Connector for small top (O).
PRODUCT NO. 088-1760-6 Step 16 Requires G, I, BB, FF, GG ASSEMBLY Attach the lower end of Middle bar of large roofs (G) to Lower middle beam connectors (I) using M6x55 screws (FF), M6 washers (BB) and M6 nuts (GG). BB FF GG BB GG G BB FF I Step 17 Requires E1, E2, G, S, AA, BB, Z Place the Lower middle beam connectors (S) into the slot on the Middle bar for large roofs (G) and Decorative grooves (E1, E2), then attach using M6x15 bolts (AA) and M6 washers (BB).
Place the assembled frame (J1, J2) over the Slanting bar for large roofs (F1), then attach the upper end of the Slanting bar for large roof (F1) to the corner of frame (J1, J2) using M6x15 bolts (AA) and M6 washers (BB). Tighten the bolts using the wrench (Z). AA BB Z J1 J2 BB AA AA BB F1 Step 19 Requires G, J1, J2, AA, BB, Z Attach the upper end of the Middle bar for large roofs (G) to the middle of the frame (J1, J2) using M6x15 bolts (AA) and M6 washers (BB).
PRODUCT NO. 088-1760-6 Step 20 Requires G, L1, L2, M1, M2, BB, CC ASSEMBLY Attach one end of each beam (L1, L2, M1, M2,) to Middle bar for large roof (G) using M6x15 screws (CC) and M6 washers (BB). BB CC CC BB G BB CC M1 L1 M2 L2 Step 21 Requires F1, L1, L2, L3, L4, M1, M2, M3, M4, BB, CC Attach other end of each beam (L1, L2, M1, M2) to Slanting bar for large roof (F1) using M6x15 screws (CC) and M6 washers (BB).
Step 22 Requires G, L3, L4, M3, M4, BB, CC BB ASSEMBLY Attach one end of each beam (L3, L4, M3, M4) to Middle bar for large roofs (G) using M6x15 screws (CC) and M6 washers (BB). CC CC BB G BB CC M3 L3 M4 L4 Step 23 Requires F1, L3, L4, M3, M4, BB, CC Attach other end of each beam (L3, L4, M3, M4) to Slanting bar for large roof (F1) using M6x15 screws (CC) and M6 washers (BB).
PRODUCT NO. 088-1760-6 Step 24 Requires G, Y1, Y2, Y3, Y4, BB, CC ASSEMBLY Attach one end of pipes (Y1, Y2, Y3, Y4) to Middle bar for large roof (G) using M6x15 screws (CC) and M6 washers (BB). BB CC G CC BB CC BB Y2 Y4 Y1 Y3 Step 25 Requires F1, Y1, Y2, Y3, Y4, BB, CC Attach other end of pipes (Y1, Y2, Y3, Y4) to Slanting bar for large roof (F1) using M6x15 screws (CC) and M6 washers (BB).
Step 26 Requires F2, W1, W2, BB, CC BB ASSEMBLY Attach Small top roof panels (W1, W2) to Slanting bar for small roof (F2) using M6x15 screws (CC) and M6 washers (BB). CC CC CC BB BB W2 W1 Step 27 Requires N2, BB, HH Place Small top cover for slanting bars (N2) on Small top roof panels (W1, W2). Attach using M6x40 screws (HH) and M6 washers (BB).
PRODUCT NO. 088-1760-6 Step 28 Requires N1, BB, HH ASSEMBLY Attach Small top roof cover (N1) to small top using M6x40 screws (HH) and M6 washers (BB). BB HH HH N1 BB HH BB Step 29 Requires K2, Q2, BB, CC Attach Small roof covers (Q2) to Small roof top beams (K2) using M6x15 screws (CC) and M6 washers (BB).
Step 30 Requires K1, Q1, BB, CC CC BB CC BB CC Q1 BB K1 W2 Step 31 Requires J1, J2, X1, X2, X3, X4, X5, X6, X7 Attach Big cover (X1) to Big top roof big panel (X2) from right to left. Insert (X1, X2) into U shape on the frame (J1, J2). Repeat the same procedure and follow the callout sequence in figure below to attach all the other big top roof panels (X3, X4, X5, X6, X7).
PRODUCT NO. 088-1760-6 Step 32 Requires F1, X2, X3, X4, X5, X6, X7, BB, CC ASSEMBLY Attach the big top roof panels to Slanting bar for large roof (F1) using M6x15 screws (CC) and M6 washers (BB). CC BB X6 X4 X2 X3 X5 X3 X7 CC X3 X3 X5 X7 BB X2 X6 X2 X4 X5 X4 X7 X6 Step 33 Requires N3, BB, HH Attach Big top cover for slanting bars (N3) to big top roof panels using M6x40 screws (HH) and M6 washers (BB).
Step 34 Requires R1, R2, R3, BB, CC 34b) Attach Big roof middle cover (R3) between covers (R1 & R2) on the long side using M6x15 screws (CC) and M6 washers (BB). CC BB CC X2 R1 R3 R2 R1 R1 BB X4 R2 CC BB R3 X1 X6 ASSEMBLY 34a) Attach Big roof left cover (R1) to the left end of gazebo using M6x15 screws (CC) and M6 washers (BB). Similarly attach the Big roof right cover (R2) to the right end of the gazebo.
PRODUCT NO. 088-1760-6 Step 35 Requires D1, D2, U, BB, CC ASSEMBLY Attach each Baffle (U) to beams (D1, D2) using M6x15 screws (CC) and M6 washers (BB). BB CC U D1 D2 BB A BB CC CC Step 36 Requires A, C, II If using on soil or grass, pull up the Base cover (C) and anchor the Post (A) to the ground using Stakes (II). Repeat this step for every post until all the posts are anchored.
Hang Mosquito netting (R) on the inner pipe of (Y1, Y2, Y3, Y4) using Rings (JJ). Hang Wall (Q) on the outer pipe of (Y1, Y2, Y3, Y4) using Rings (JJ). Attach Wall (Q) to the corner posts with strap to keep walls open. The gazebo is ready for use.
PRODUCT NO. 088-1760-6 SPECIFICATIONS CLEANING AND MAINTENANCE CAUTION! • Check all screws and nuts periodically for tightness; fasten them as required. • Disassemble the gazebo in reverse order of the steps used to assemble. Always disassemble the gazebo completely. A partially-disassembled gazebo is not stable enough to resist wind and bad weather, and therefore can be damaged and/or cause damage. • Clean the gazebo gently with water using a sponge.
This CANVAS™ product carries a three (3) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear or breakage due to misuse and/or abuse.
