Speed Dome Web3.0 Operation Manual Version 1.0.
Table of Contents 1 2 3 Network Connection ................................................................................................................... 1 1.1 Preparation..................................................................................................................... 1 1.2 Log in .............................................................................................................................. 1 1.3 Live Interface .................................................
.1.1 Conditions ............................................................................................................. 13 3.1.2 Video ...................................................................................................................... 24 3.1.3 Audio ...................................................................................................................... 31 3.2 Network......................................................................................................
3.4 Peripheral ..................................................................................................................... 58 3.4.1 IR Light .................................................................................................................. 58 3.4.2 Wiper ...................................................................................................................... 59 3.5 Event ................................................................................................
3.8.1 Version ................................................................................................................... 77 3.8.2 Log.......................................................................................................................... 78 3.8.3 Online User ........................................................................................................... 79 4 Alarm ..........................................................................................................
1 Network Connection 1.1 Preparation This series speed dome product supports the Web access and management via PC. Web includes several modules: monitor channel preview, PTZ control, system configuration, alarm and etc. Please follow the steps listed below for network connection. Make sure the speed dome has connected to the network properly. Speed dome IP address and PC IP address shall be in the same network segment. If there is router, please set the corresponding gateway and subnet mask.
Figure 1-2 For WIN 7 and higher version of operating system, it is advised to operate as an administrator if it is your first time to log in. 1.3 Live Interface After you logged in, you can see the live monitor window. Now you can operate the speed dome via the WEB. See Figure 1-3.
Figure 1-3 There are six sections: Section 1: Encode setup bar Section 2: Window adjust bar Section 3: System menu bar Section 4: Window function option bar Section 5: PTZ control Section 6: PTZ function 1.4 Encode Setup The encode setup interface is shown as in Figure 1-4. Figure 1-4 Please refer to the following sheet for detailed information. Parameter Function Main stream In normal network width environment, main stream can record video file and realize network monitor.
3 Full screen Click it to go to full-screen mode. Double click the mouse or click the Esc button to exit the full screen. 4 Width and height ratio Click it to restore original ratio or suitable window. 5 Open/close PTZ interface Left click it to display or hide the PTZ control interface. The picture setup interface is shown as in Figure 1-6. Figure 1-6 Please refer to the following sheet for detailed information. Parameter Function Video setup Brightness setup icon.
--- Width and height rate. Adjust to original size or suitable for the window. --- Fluency setup. It has three modes: real-time/general/fluency. ---Open/close PTZ interface. Left click mouse to display or hide PTZ control interface. 1.6 System Menu System menu is shown as in Figure 1-7. Please refer to chapter 1.3 Live, chapter 2 Playback，Chapter 3 Setup, chapter 4 Alarm, chapter 5 Log out for detailed information. Figure 1-7 1.7 Video Window Function Option The interface is shown as below.
4 Snapshot You can snapshoot important video. You can go to Setup->Camera->Video->Path to modify the local record save path. 5 Triple snap 6 Record Click it, system can snap at 1f/s for three times. All images are memorized in system storage folder. When you click local record button, the system begins recording. You can go to Setup->Camera->Video->Path to modify the local record save path. 7 Audio output Turn on or off audio when you are monitoring. You can go to Setup->Camera->Audio to set.
1.9 PTZ Setup The PTZ setup interface is shown as in Figure 1-10. Figure 1-10 Click PTZ set button, the interface is shown as in Figure 1-11.Here you can select scan, preset, tour pattern, assistant function and etc. Figure 1-11 Please refer to the following sheet for PTZ setup information.
Parameter Function Scan Select Scan from the dropdown list, click Start button, you can begin scan operation. Default SN is 1. Preset Tour Pattern Input the preset value and then click View button, the camera turns to the corresponding position of the preset. Select Tour from the dropdown list and then click Start button, you can begin tour. You can select Pattern from the dropdown list and then click Start button to begin PTZ movement. Assistant Reserved assistant function.
2 Playback 2.1 Playback Interface The playback interface is shown as in Figure 2-1. Figure 2-1 You can refer to the following sheet for detailed information. SN Name 1 Playback control button 2 Date 3 File list 4 Time process format 2.2 Playback Control Button Playback control button is shown as below. See Figure 2-2.
Figure 2-2 You can refer to the following sheet for detailed information. SN Name Function 1 Play To start or resume playback. 2 Stop Stop current playback. 3 Frame by frame Play next frame. Please pause playback first if you want to use frame by frame playback function. 4 Slow play Slow playback. 5 Fast play Fast playback. 6 Mute Click it to mute. Click it again to restore audio function. 7 Volume Set record volume level. 2.3 Date The colors here have different meanings. Green: Current selected data.
Figure 2-3 You can refer to the following sheet for detailed information. Icon Name Function Search It is to search record from the start time of you selected date to the previous 24 hours. Stop Click it to download selected file(s) to local PC. Back Click it to go back to calendar interface to select date again.
2.5 Process bar format You can refer to the following sheet for detailed information. Icon Function Process bar is in 24H mode. It is to display the record files of previous two hours. It is to display the record files of previous one hour. It is to display the record files of previous 30 minutes.
3 Setup 3.1 Camera 3.1.1 Conditions Here you can set camera property. Adjust video parameter to get best preview effect. See Figure 3-1. Figure 3-1 Please refer to the following sheet for detailed information. Parameter Function Config File Here you can set camera setup mode. It includes: normal/day/night. White Balance It is to set camera white balance. It includes: auto/manual/ATW/outdoor/indoor/outdoor auto/sodium light auto/sodium light. Exposure It is to set camera exposure mode.
Zoom It is to set digital zoom/camera zoom rate. You need to check the box here to enable digital zoom function. Sharpness It is to set camera lens sharpness, and sharpness control level. Picture It is to set camera video. It includes: style/hue/brightness/saturation/ chroma control/gamma/picture flip/picture freeze. It is to set camera defog mode, including off and auto. It is to restore factory default setup.
Exposure interface is shown as below. See Figure 3-3. Figure 3-3 Please refer to the following sheet for detailed information. Parameter Function Exposure mode Anti-flicker It is to set camera exposure mode. It includes: auto/manual/aperture has the priority/shutter has the priority. The default setup is auto. For the auto exposure mode, the gain, shutter and iris are in auto mode. For manual exposure mode, the gain, shutter and aperture is in manual mode.
Slow exposure Max Auto gain Slow shutter Auto Slow Shutter Min value If the light may change greatly, you can use slow exposure to get image so that the camera can get stable video. It is to set camera max gain. In lower illumination environment, you can lower the cameras auto exposure time to capture the image and enhance the definition. For the moving object , the trail may appear. Please note it is valid in auto mode. It is to set camera min shutter value.
Figure 3-4 Please refer to the following sheet for detailed information. Parameter Function 2D NR It is to control noise. The higher the level is; the small the noise is. Comparing with the previous one, the picture may become a little bit blurry. 3D NR It is to control noise. The higher the level is; the small the noise is. Comparing with the previous one, there may appear some smear phenomenon. 3.1.1.4 Day & Night Important Please make sure your purchased product camera supports this function.
Figure 3-5 Please refer to the following sheet for detailed information. Parameter Function Day & night It is to set camera day/night mode. The type includes: electronic/mechanical. The mode includes: B&W/color/auto/photosensor. It is to camera day & night switch sensitivity. Sensitivity 3.1.1.5 Focus The focus interface is shown as in Figure 3-6.
Figure 3-6 Please refer to the following sheet for detailed information. Parameter Function Focus mode It is to set camera focus mode. It includes: auto/manual/semi auto. It is to camera focus distance in case the focus distance is too small and the focus goes to the enclosure. At the same time, you can change focus distance to adjust focus speed. It is to set camera focus sensitivity. The higher the value is, the easier it is to activate focus.
Figure 3-7 Please refer to the following sheet for detailed information. Parameter Function Zoom speed It is to set camera zoom speed. The bigger the value is, the faster the speed is. Digital zoom Check the box here to enable digital zoom function. 3.1.1.7 Sharpness Sharpness interface is shown as in Figure 3-8.
Figure 3-8 Please refer to the following sheet for detailed information. Parameter Function Sharpness It is to set camera sharpness. The higher the sharpness is, the clear the image is. The object edge becomes clear too. It is to set camera control level. The higher the value is, the strong the control level is. Sharpness control level 3.1.1.8 Picture Picture interface is shown as in Figure 3-9.
Figure 3-9 Please refer to the following sheet for detailed information. Parameter Function Style It is to set video style. It includes：Standard/soft/ flamboyant. Hue It is to set picture hue. Saturation It is to set color purity. The higher the purity is, the more color the video is. The lower the purity is, the dark the video is. It is to set video color control level. The higher the value is, the higher the control level is. It is to set image gamma value.
Figure 3-10 Parameter Function Mode It is to set the camera defog mode, including off and auto. Intensity It is to set defog intensity, able to select only when the defog mode is auto. 3.1.1.10 Default Default interface is shown as in Figure 3-11.
Figure 3-11 Please refer to the following sheet for detailed information. Parameter Function Default It is to restore camera parameter to factory default setup. 3.1.1.11 Profile Management Profile management interface is shown as in Figure 3-12. Figure 3-12 Please refer to the following sheet for detailed information. Parameter Function Profile Management There are three modes: normal/full-time/schedule. The default setup is normal. Normal It is to adopt the general parameter on the profile file.
Figure 3-13 Please refer to the following sheet for detailed information. Parameter Function Main stream It includes general stream, motion stream and alarm stream. You can select different encode frame rates for different recorded events. The frame rates of the motion detect and alarm is customized. There are four options: H.264, H.264H, and MJPEG encode mode. Bit stream type Encode mode Resolution H.264 : Main Profile encode mode. H.264H: High Profile encode mode.
Parameter Function Bit Rate Type There are two options: VBR and CBR. Please note, you can set video quality in VBR mode. In MJPEG mode, the bit stream control mode can only be CBR. Recommended Bit Recommended bit rate value according to the resolution and frame rate you have set. Bit Rate In CBR, the bit rate here is the average value. usually it is within a range of ±10%. In dynamic video, system needs to lower frame rate or video quality to guarantee the value.
Parameter Function Frame Rate (FPS) PAL: 1～25f/s，NTSC: 1～30f/s.. Bit Rate Type There are two options: VBR and CBR. Please note, you can set video quality in VBR mode. Recommended Bit Recommended bit rate value according to the resolution and frame rate you have set. Bit Rate The frame rate may vary due to different resolutions. In CBR, the bit rate here is the average value. usually it is within a range of ±10%.
Parameter Function Snapshot type There are two modes: general (schedule) and Event (activation). General (schedule) snapshot is to snap in the specified period. Event (Activation) snapshot Is to snap when the motion detect, camera masking, local alarm event occurrence. If you want to use this function, please make sure: The event occurred during the specified period. Motion detect, video masking, local alarm and corresponding snap function are all enable.
Figure 3-16 Figure 3-17 29
Figure 3-18 Please refer to the following sheet for detailed information. Parameter Privacy mask Channel Title Function Select a “privacy mask SN”, click “Draw”, and then you can draw the privacy mask zone which is corresponding to the privacy mask SN in the video monitoring window. Click “Delete” to delete the privacy mask zone which is corresponding to the privacy mask SN. Click “Clear” to clear all the privacy mask zones which are drawn by users.
Parameter Function Refresh After you successfully set channel title, time title, OSD Info, you can click Refresh button to video the effect. 3.1.2.4 Path The storage path interface is shown as in Figure 3-19. Here you can set snap image saved path ( ( in the preview interface) and the record storage path in the preview interface).The snap picture default setup is C:\PictureDownload and record file default setup is C:\RecordDownload. Please click the Save button to save current setup. Figure 3-19 3.
Figure 3-20 Please refer to the following sheet for detailed information. Parameter Function Sampling frequency It is to set the sampling frequency of audio Microphone volume It is to set the volume of the microphone Speaker volume It is to set the volume of the speaker Audio enable Encode mode Main stream: Recorded file only contains video by default. You need to check the audio box here to enable audio function so that the main stream the network transmitted is audio/video composite stream.
Figure 3-21 Please refer to the following sheet for detailed information. Parameter Function Host Name It is to set current host device name. Ethernet Card Please select the Ethernet port if the device has several network cards. Mode There are two modes: static mode and the DHCP mode. Mac Address The IP/subnet mask/gateway are null when you select the DHCP mode to auto search the IP. If you select the static mode, you need to set the IP/subnet mask/gateway manually.
IP Version It is to select IP version. IPv4 or IPv6. You can access the IP address of these two versions. Please note system needs to check the validity of all IPv6 addresses. The IP address and the default gateway shall be in the same IP section. That is to say, the specified length of the subnet prefix shall have the same string. When PPPoE function is enabled, the IP/subnet mask/default gateway is read-only. You cannot set or restore default setup.
3.2.2.1 Connection The connection interface is shown as in Figure 3-22. Figure 3-22 Please refer to the following sheet for detailed information. Parameter Function Max connection It is the max Web connection for the same device. The value ranges from 1 to 20. The default setup is 10. TCP port The value ranges from 1025 to 65535. The default value is 37777. You can input the actual port number if necessary. UDP port The value ranges from 1025 to 65535. The default value is 37778.
RTSP port Usually, the default value is 554. You do not need to input again if you are using the default value. When you are using QuickTime (Apple browser) or VLC play real-time video, you can use the following format to play. The Blackberry also supports this function. Real-time monitor bit stream Url format. Please specify the channel number, bit stream type in the Url if you are requesting real-time monitor bit stream Rtsp stream media service.
Figure 3-23 3.2.3 PPPoE The PPPoE interface is shown as in Figure 3-24. Input the PPPoE user name and password you get from the IPS (internet service provider) and enable PPPoE function. Please save current setup and then reboot the device to get the setup activated. Device connects to the internet via PPPoE after reboot. You can get the IP address in the WAN from the IP address column. PPPoE is set to connect to the internet.
Figure 3-24 3.2.4 DDNS The DDNS interface is shown as in Figure 3-25. The DDNS is to set to connect the various servers so that you can access the system via the server. Please go to the corresponding service website to apply a domain name and then access the system via the domain. It works even your IP address has changes.
Figure 3-25 Please refer to the following sheet for detailed information. Parameter Function Server Type You can select DDNS protocol from the dropdown list and then enable DDNS function. Server IP DDNS server IP address Domain Name Your self-defined domain name. User The user name you input to log in the server. Password The password you input to log in the server. Update period Device IP and service connection refresh period. The default setup is 10 minutes. 3.2.
3.2.6 SMTP （e-mail） The SMTP interface is shown as in Figure 3-27. Figure 3-27 Please refer to the following sheet for detailed information. Parameter Function SMTP Server Input server address and then enable this function. Port Default value is 25. You can modify it if necessary. Anonymity For the server supports the anonymity function. You can auto login anonymously. You do not need to input the user name, password and the sender information. User Name The user name of the sender email account.
Parameter Function Mail receiver Input receiver email address here. Max three addresses. Interval The send interval ranges from 0 to 3600 seconds. 0 means there is no interval. Please note system will not send out the email immediately when the alarm occurs. When the alarm, motion detection or the abnormity event activates the email, system sends out the email according to the interval you specified here.
Figure 3-28 Figure 3-29 3.2.8 SNMP The SNMP interface is shown as in Figure 3-30.
The SNMP allows the communication between the network management work station software and the proxy of the managed device. Please install the software such as MG MibBrowser 8.0c software or establish the SNMP service before you use this function. You need to reboot the device to activate the new setup. Figure 3-30 Please refer to the following sheet for detailed information. Parameter Function SNMP Port The listening port of the proxy program of the device. It is a UDP port not a TCP port.
Parameter Function Trap address The destination address of the Trap information from the proxy program of the device. The destination port of the Trap information from the proxy program of the device. It is for the gateway device and the client-end PC in the LAN to exchange the information. It is a non-protocol connection port. It has no effect on the network applications. It is a UDP port not TCP port. The value ranges from 1 to 165535. The default value is 162.
Figure 3-31 3.2.10 Multicast The multicast interface is shown as in Figure 3-32. Multicast is a transmission mode of data packet. When there is multiple-host to receive the same data packet, multiple-cast is the best option to reduce the broad width and the CPU load. The source host can just send out one data to transit. This function also depends on the relationship of the group member and group of the outer. Here you can set multicast address and port.
Figure 3-32 3.2.11 IEEE802 IEEE802.1X works standing for local and metropolitan area networks and port based network access control protocol. It supports manual operation of the client to choose means of authenticating by which to control it to access to the Local Area Networks or not. It supports the ability to authenticate, to calculate fee, to ensure security and to maintain requirements. See Figure 3-33.
Figure 3-33 Please refer to the following sheet for detailed information. Parameter Function Authentication PEAP (protected EAP protocol). Username It needs the username to login, which is authenticated by the server. Password Please input password here. 3.2.12 Qos The QoS interface is shown as below. See Figure 3-34. Qos (Quality of Service) is network security mechanism. It is a technology to fix the network delay and jam problem and etc.
Parameter Function Real-time monitor The data packet of the network video monitor. Command The non-monitor packet such as device setup and search. 3.3 PTZ 3.3.1 Protocol 3.3.1.1 Network PTZ Setup Network PTZ setup interface is shown as in Figure 3-35. Figure 3-35 Please refer to the following sheet for detailed information. Parameter Function Protocol You can select from the dropdown list such as DH-SD1/DH-SD3 3.3.1.2 Analog PTZ The analog PTZ is shown as in Figure 3-36.
Please refer to the following sheet for detailed information. Parameter Function Address It is to set the corresponding speed dome address. The default setup is 1. Baud rate It is to set the baud rate of the camera. The default setup is 9600. Data bit The default setup is 8. Stop bit The default setup is 1. Parity You can set protocol parity mode. The default setup is none. 3.3.2 Function Figure 3-37 In this part, you can operate the PTZ of the camera and control PTZ movement.
Pan Set camera rotation speed. PTZ speed Set PTZ movement speed. Idle motion Set camera idle operation. Power up Set camera operation when system boots up. PTZ restart Restart camera PTZ. Default Restore camera PTZ default setup. 3.3.2.1 Preset Preset interface is shown as in Figure 3-38. Figure 3-38 Please refer to the following sheet for detailed information. Parameter Function Preset No. Set preset No. It becomes valid after you set. Preset title Set preset name.
Save Save current preset setup. Add Click it to add a new preset. Clear Clear all presets setup. 3.3.2.2 Tour Tour interface is shown as below. See Figure 3-39. Figure 3-39 Please refer to the following sheet for detailed information. Parameter Function Tour No. System auto allocates. Tour title Set tour name. You can input self-defined tour name here. Start /Stop Begin or stop tour. Please note this function is null if you have not set a tour. Add Click it to add a new tour.
Please set presets before you use tour function. Duration (Interval) Save Refresh It is to set the staying time of the tour. Click it to save current setup. Refresh current interface. 3.3.2.3 Scan Scan interface is shown as below. See Figure 3-40. Figure 3-40 Please refer to the following sheet for detailed information. Parameter Function Scan No. System auto allocates. Speed Set scan speed here. You cannot set speed when camera is running scan. Start /Stop Begin or stop scan.
Right limit Set camera right limit. 3.3.2.4 Pattern Pattern interface is shown as below. See Figure 3-41. Figure 3-41 Please refer to the following sheet for detailed information. Parameter Function Pattern No. System auto allocates. Start /Stop Begin or stop pattern. Please note this function is null if you have not set a pattern. Set Click it you can see start/stop record buttons. Start record Click it to begin recording pattern setup. Stop record Click it to stop recording pattern setup.
Figure 3-42 Please refer to the following sheet for detailed information. Parameter Function Pan speed It is to set camera pan speed. Start /Stop Check it to start or stop pan movement. 3.3.2.6 PTZ speed PTZ speed interface is shown as below. See Figure 3-43.
Figure 3-43 Please refer to the following sheet for detailed information. Parameter Function PTZ speed Here you can set camera PTZ speed. 3.3.2.7 Idle Motion Idle motion interface is shown as below. See Figure 3-44.
Figure 3-44 Please refer to the following sheet for detailed information. Parameter Function Enable Check the box here to enable idle motion function. Idle Motion Here you can set preset, scan, pattern, tour. Please note you need to set the corresponding operation first if you want to use this function. Idle time Set idle time. 3.3.2.8 Power up Power up interface is shown as below. See Figure 3-45. Figure 3-45 Please refer to the following sheet for detailed information.
Figure 3-46 Please refer to the following sheet for detailed information. Parameter Function PTZ restart It is to reboot PTZ. 3.3.2.10 Default Default interface is shown as below. See Figure 3-47.
Please refer to the following sheet for detailed information. Parameter Function Default Restore PTZ factory default setup. 3.4 Peripheral 3.4.1 IR Light Important Please make sure your purchased camera supports all the functions listed here. The IR light has two interface: zoom has the priority(Figure 3-48)/manual has the priority(Figure 3-49).
Figure 3-49 Please refer to the following sheet for detailed information. Parameter Function Zoom has the priority Enable IR light when the zoom has the priority. The IR light near light value/far light value can automatically switch according to the zoom. Manual has the priority You can set IR light near/far value under manual mode. 3.4.
Parameter Function Mode Able to select manual and timing, timing is default. Interval time The interval from the wiper stops to it begins. Period Check enable, and you can set the period when the wiper enables. (it only exists when the mode is “Timing”) 3.5 Event 3.5.1 Video detect 3.5.1.1 Motion Detect The motion detect interface is shown as in Figure 3-51.
Figure 3-52 Figure 3-53 Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable motion detection function. Region There are six levels. The sixth level has the highest sensitivity. Region: If you select motion detection type, you can click this button to set motion detection zone. The light blue zones are the valid motion detect area. All areas are the valid motion detect zone by default. You can use mouse to set invalid area.
Parameter Function Record channel System auto activates motion detection channel to record once motion detect alarm occurs (working with motion detection function). Please note you need to go to Storage-> Schedule to set motion detect record period and go to Storage->Record control to set current channel as auto record. Record Delay System can delay the record for specified time after motion detect alarm ended. The value ranges from 10s to 300s. Relay out Enable alarm activation function.
Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable video masking function. Working Period Video masking function becomes activated in the specified periods. There are six periods in one day. Please draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole week.
Figure 3-55 Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable this function. Working Period This function becomes activated in the specified periods. There are six periods in one day. Please draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole week.
Parameter Function Record Channel System auto activates motion detection channel to record once alarm occurs (working with motion detection function). Please note you need to go to Storage-> Schedule to set current channel as general record. Record Delay System can delay the record for specified time after alarm ended. The value ranges from 10s to 300s. Send Email If you enabled this function, System can send out email to alert you when alarm occurs and ends.
Figure 3-57 Figure 3-58 Figure 3-59 Figure 3-60 Please refer to the following sheet for detailed information.
Parameter Function Event Type The abnormal events include: no SD card, no space, SD card error, disconnection, IP conflict. You need to draw a circle to enable this function. Record System auto activates channel to record once an alarm occurs (For disconnection type only. See Figure 3-59. ). You need to check the box to enable this function. Record Delay System can delay the record for specified time after alarm ended. The value ranges from 10s to 300s.
Figure 3-61 3.6.2 Destination The destination interface is shown as in Figure 3-62. It is to set the storage mode of the speed dome record file or snapshot pictures. There are three options: path/local storage/FTP. You can only select one mode. System can save according to the event types. It is corresponding to the three modes (general/motion/alarm) in the Schedule interface. Please check the box to enable the save functions. Figure 3-62 Please refer to the following sheet for detailed information.
The local interface is shown as in Figure 3-63. Here you can view local SD card information. You can also operate the read-only, write-only, hot swap and format operation. Figure 3-63 The FTP interface is shown as in Figure 3-64. You need to check the box to enable the FTP function. When network disconnect occurred or there is malfunction. Emergency storage can save the record/snapshot picture to the local SD card. Figure 3-64 3.6.3 Record control The record control interface is shown as in Figure 3-65.
Figure 3-65 Please refer to the following sheet for detailed information. Parameter Function Pack Duration Here you can select file size. Default setup is 60 minutes. Pre-record Please input pre-record value here. For example, you can input 4 here so that system can read the previous four seconds video before the alarm occurrence from the buffer and record the 4 seconds video in the file.
Figure 3-66 Please refer to the following sheet for detailed information. Parameter Function Device Name It is to set device name. Video Standard This is to display video standard. Language You can select the language from the dropdown list. The browser can refresh automatically and change the language accordingly. 3.7.1.
Please refer to the following sheet for detailed information. Parameter Function Date format Here you can select date format from the dropdown list. Time Format There are two options: 24-H and 12-H. Time zone The time zone of the device. System time It is to set system time. It becomes valid after you set. Sync PC You can click this button to save the system time as your PC current time. DST Here you can set day night save time begin time and end time.
Figure 3-68 Add user: It is to add a name to group and set the user rights. See Figure 3-69. Here you can input the user name and password and then select one group for current user. Please note the user rights shall not exceed the group right setup. For convenient setup, please make sure the general user has the lower rights setup than the admin. Figure 3-69 Modify user It is to modify the user property, belonging group, password and rights. See Figure 3-70.
It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup. Please click the OK button to save. For the user of the account rights, he can modify the password of other users. Figure 3-70 3.7.2.2 Group The group management interface can add/remove group, modify group password and etc. The interface is shown as in Figure 3-71. Figure 3-71 Add group: It is to add group and set its corresponding rights. See Figure 3-72.
Figure 3-72 Modify group Click the modify group button, you can see an interface is shown as in Figure 3-73. Here you can modify group information such as remarks and rights. Figure 3-73 3.7.3 Default The default setup interface is shown as in Figure 3-74. Please note system cannot restore some information such as network IP address.
Figure 3-74 3.7.4 Import/Export The interface is shown as in Figure 3-75. Figure 3-75 Please refer to the following sheet for detailed information. Parameter Function Import It is to import the local setup files to the system. Export It is to export the corresponding system setup to your local PC. 3.7.5 Auto maintenance The auto maintenance interface is shown as in Figure 3-76. Here you can select auto reboot and auto delete old files interval from the dropdown list.
Figure 3-76 3.7.6 Firmware update The firmware interface is shown as in Figure 3-77. Please select the upgrade file and then click the update button to begin firmware update. Important Do not turn off the device power, disconnect the device, reboot or shutdown the device during the update period. Please reboot the device if you update the improper program, otherwise some function module of the device may become null! Figure 3-77 3.8 Information 3.8.
Here you can view system software version, WEB version, release date and etc. Please note the following information is for reference only. Figure 3-78 3.8.2 Log 3.8.2.1 System Log Here you can view system log. See Figure 3-79. Figure 3-79 Please refer to the following sheet for log parameter information. Parameter Function Type Log types include: system operation, configuration operation, data operation, event operation, record operation, and user management, log clear.
Parameter Function Start time Set the start time of the requested log. End time Set the end time of the requested log. Search You can select log type from the drop down list and then click search button to view the list. You can click the stop button to terminate current search operation. You can select one item to view the detailed information. Detailed information Clear You can click this button to delete all displayed log files.
Figure 3-81 80
4 Alarm Click alarm function, you can see an interface is shown as in Figure 4-1. Here you can set device alarm type and alarm sound setup. When the specified alarm occurred (you have subscribed), system can record the corresponding alarm information on the right pane of the alarm list. Figure 4-1 Please refer to the following sheet for detailed information. Type Parameter Function Alarm Motion detect System alarms when motion detection alarm type occurs, Disk full System alarms when disk is full.
5 Log out Click log out button, system goes back to log in interface. See Figure 5-1. You need to input user name and password to login again. Figure 5-1 Note: This manual is for reference only. Slight difference may be found in user interface. All the designs and software here are subject to change without prior written notice. All trademarks and registered trademarks are the properties of their respective owners.
