Wireless Remote Control BR-E1 E INSTRUCTION MANUAL 1
Introduction The Wireless Remote Control BR-E1 is a wireless remote controller that is compatible with Bluetooth® low energy technology (hereafter “Bluetooth”). Pairing the remote controller with a Bluetooth-compatible Canon digital camera* enables the following operations to be performed wirelessly (with an operating distance of approx. 5 m/16.4 ft. in any direction). * For information on the supported cameras, refer to the Canon Web site, etc.
Conventions Used in this Manual Icons in this Manual (p.**) : Reference page numbers for more information. : Warnings to prevent potential problems during operation. : Supplemental information. Trademarks The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Canon Inc. is under license. Other trademarks and trade names are those of their respective owners.
Contents Introduction....................................................................................... 2 Features of the BR-E1 ................................................................... 2 Conventions Used in this Manual..................................................... 3 Safety Precautions ........................................................................... 5 Handling Precautions .......................................................................
Safety Precautions The following precautions are provided to prevent harm or injury to yourself and others. Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Warnings: Follow the warnings below. Otherwise, death or serious injuries may result.
Handling Precautions Do not immerse the product in water. Wipe off any water droplets with a dry and clean cloth. If the product is exposed to salty air, wipe it with a clean, well-wrung wet cloth. Holding the Remote Controller When operating the remote controller, hold it as indicated in the figure below. Do not cover this part with your fingers. Doing so may cause the operating distance to become shorter.
Cautions for Using the Remote Controller If remote control operation takes time or fails, or if other problems occur, try the following corrective actions. Distance Between the Camera and This Product The operating distance of this product is approx. 5 m/16.4 ft. in all directions. Remote operations may not be possible if this product is too far away from the camera. In such a case, perform remote control operations after bringing this product closer to the camera.
Nomenclature Release button Power zoom < > Wide-angle button < > Telephoto button Indicator lamp (red) < > AF start button < > Immediate release < > 2-sec. delay release Release timing/ Movie shooting switch < < > Movie shooting > Bluetooth logo Battery compartment cover Battery compartment cover screw The product does not come with a strap.
Connecting the Remote Controller and Camera Connect the remote controller and camera using the Bluetooth function. To connect the remote controller and camera via Bluetooth, first you need to pair the camera and remote controller (registering the device to the camera). 1 Set the camera to the pairing standby mode. Select [Pairing] from the menu screen of the camera. For details, refer to the pages regarding BR-E1 in the Camera Instruction Manual. the remote controller to 2 Connect the camera.
Connecting the Remote Controller and Camera Pairing with two or more cameras simultaneously is not possible. If you pair a camera and the remote controller that has already been paired with another camera, remote operation of the previously paired camera cannot be performed. Remove the registration of the remote controller, then pair with the other camera. If you cannot select [Pairing] from the menu screen of the camera to pair, the camera may be paired with another remote controller.
Checking Registered Information/ Removing Registration You can check the registered information of a paired remote controller or remove a registration from the menu screen of the camera. Checking Registered Information When the remote controller is paired correctly, the 12-digit number on the back of the remote controller (the Bluetooth address) is displayed on the camera’s LCD monitor. If the number is incorrect, remove the registration of remote controller and perform pairing again.
Shooting Still Photos 1 Set up the camera for remote control shooting. Set the camera for still photo shooting. Set the drive mode of the camera to < > (remote control). the release method. 2 Select Set the release timing/movie shooting switch on the remote controller to the < > (immediate release) or < > (2sec. delay release) position. a picture. 3 Take When you press the release button on the remote controller, the camera automatically focuses (AF), and takes a picture when focus is achieved.
Shooting Movies 1 Set up the camera for remote control shooting. Set the camera for movie shooting. Set [Remote control] to [Enable] from the menu screen of the camera. the switch to < >. 2 Set Set the release timing/movie shooting switch on the remote controller to the < > position. the movie. 3 Shoot When you press the release button on the remote controller, the indicator lamp lights up and movie shooting starts.
Operating the Power Zoom Adapter The Power Zoom Adapter is a lens accessory (sold separately). For information on how to attach to the lens and operate the Power Zoom Adapter, refer to its Instruction Manual. 1 Prepare the Power Zoom Adapter. Attach the Power Zoom Adapter to the lens, then attach the lens to the camera. Set the zoom mode switch of the Power Zoom Adapter to the position. up the camera for remote 2 Set control shooting. Set the drive mode of the camera to < > (remote control).
Replacing the Battery If the indicator lamp does not light up when you press a button on the remote controller, replace the battery. Use one lithium button cell battery CR2032. CR2032 Make sure to insert the battery with the positive (+) side face up, as indicated in the figure above.
Specifications Type: Compliance standards: Remote controller Bluetooth Specification Version 4.1 (Bluetooth low energy technology) Transmission method: GFSK modulation Operating distance: Approx. 5 m/16.4 ft. from the camera in any direction * With no obstructions between the remote controller and camera and no radio interference Power: Lithium button cell battery CR2032 Battery life: Approx. one year Dimensions (W x H x D): Approx. 27.0 x 91.5 x 12.0 mm/1.06 x 3.60 x 0.47 in. Weight: Approx. 14 g/0.49 oz.
Wireless Communication Function Countries and Regions Permitting Wireless Communication Function Use Use of wireless communication function is restricted in some countries and regions, and illegal use may be punishable under national or local regulations. To avoid violating wireless regulations, visit the Canon Web site to check where use is allowed. Note that Canon cannot be held liable for any problems arising from wireless communication function use in other countries and regions.
Wireless Communication Function Model: DS586111 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to Part 15 of the FCC Rules.
Index Numerics 2-sec. delay release..........................8 A AF start button ..................................8 B R Release button ............................... 12 Removing registration .................... 11 Replacing the battery ..................... 15 S Safety Precautions ........................... 5 Bluetooth...........................................9 Shooting movies............................. 13 ......................................................8 Shooting still photos .........
The descriptions in this Instruction Manual are current as of February 2017. For information on the compatibility with any products introduced after this date, contact any Canon Service Center. For the latest version Instruction Manual, refer to the Canon Web site. CPA-E323-000 © CANON INC.
