Canon • '" • t( ExitPtint PictBridge Photo Printer PI}(MA iP6320D I iP631 OD Series Quick Start Guide ~ •........... ~ AiIlIl1IiIIf:•...••.•...•... _ illl!l8 _ JJIIIIIIIIIf·.AlIIIIIIIIIIIf_ JI1fI1fff . ........ ~ _ ..,.4iii!iIr '-' -~7~J~~ ......., .- . - .
Getting Help from Canon Help Us Help You Better Before you contact Canon, please record the following information. Serial Number (located on the inside of the product): _ Model Number (located on the top of the product): Setup CD-ROM number (located on the CD-ROM): _ _ Purchase Date:- - - - - - - - - - - - - - - - - - - - - - - - - - Customer Technical Support Sequence* 1. Internet - www.canontechsupport.
Canou PI}{MA iP6320D/iP6310D Photo Printer Quick Start Guide
Canon PIXMA iP6320D/iP63100 Photo Printer Quick Start Guide The diagrams and computer screens in this guide refer to the iP6320D. The operations are the exactly the same with the iP6310D, unless otherwise described. Copyright This manual is copyrighted by Canon U.S.A., Inc. with aU rights reserved. Under the copyright laws, this manual may not be reproduced in any form, in whole or in part, without the prior written consent of Canon U.S.A., Inc. © 2006 Canon U.S.A., Inc. Disclaimer Canon U.S.A., Inc.
Contents Contents Basic Printing Turning on the Printer •.•.•.•.•..••..•••.••.•..•.••.••.•....•.•••.•..••..•.•••••.•... 2 Turning off the Printer ..........•..................•.••...•.......•.......•......•... 3 Loading Paper .••..•....•............••....•..•.................•.•................ 4 Using Specialty Media ...••••.•..•.••.•..•...••..••.•.•.....••.••.••.••.••••..•••.•. 9 Printing with Windows. . . . . . . . . . . . . . • • . . . • . • . • . . . . . . . . . • . . . . . . . . . . • . . • . . . . .
Basic Printing Basic Printing W Note This Quick Start Guide describes some of the features of your printer and how to use them. For more information, view the iP6320D/iP6310D User's Guide, Printer Driver Guide, and Photo Application Guide installed on your computer, or use the online help within your printer driver interface: ,~,~-, ~ While in the printer's properties dialog box, press the F1 key, or click 6 in the upper right corner.
Basic Printing Turning off the Printer 1 To turn off the printer, press the POWER button. When the POWER lamp stops blinking, the printer is turned off. ~Important About the Power Plug When removing the power plug after turning off the printer, be sure to check that the POWER lamp is not lit. If the power plug is removed from the wall outlet with the POWER lamp lit or blinking, the printer cannot protect its print heads and may be unable to print.
Basic Printing Loading Paper • Print Media to Avoid Do not use the following types of paper. Using such paper will not only produce unsatisfactory results, but can also cause the printer to jam or malfunction.
Basic Printing • Preparing the Printer W Note • • 1 Flatten the four corners of the paper before loading it. W 2 For detailed information on the specialty media Canon provides for use with its various printers, see "Using Specialty Media" on page 9. Consult "Printing Media" in the User's Guide for detailed instructions on how to load specialty media into the printer.
Basic Printing 3 Load the paper. • Loading Plain Paper Load limit mark Do not load beyond this load limit mark. (1) Insert the paper into the auto sheet feeder with the print side facing up. When loading the 4" x 6" paper, load sheets in the portrait position (short side facing down). (2) Align the paper stack against the right side of the auto sheet feeder. (3) Pinch the paper guide and slide it against the left side of the paper stack.
Basic Printing • Loading Envelopes Use either European DL or US Comm. #10 size envelopes. The address is automatically rotated and printed out. ~Important • • • Do not use envelopes with embossed or treated surface, with a double flap or pressure seals, with sticker flaps. Select either DL Env. or Comm. Env. #10 in the printer driver according to the envelope size you are using. If you do not select Media Type correctly, the print out results in the wrong way round. Fold the envelope flap shut.
Basic Printing • Loading Other Small-Sized Paper (1) Align the paper against the right side of the auto sheet feeder. Regardless to the actual orientation of your photograph, load the paper vertically (short side first) in the printer. A maximum of 20 sheets of size in 4" x 6 11 paper can be loaded at one time. (2) Pinch the paper guide and slide it against the left side of the paper stack. (3) Select 4x6in 101.6x152.4mm, 5x7in 127.0x177.8mm or Credit Card 2.13x3.
Basic Printing Using Specialty Media Canon recommends that you use Canon genuine paper to ensure optimal print quality.
Basic Printing • Canon genuine paper i Paper Support load limit I PaperThickness i Printer Driver Settings Media Name i High Resolution Paper I Letter: up to 80 sheets Super White Paper Letter: up to 10mm Letter: up to 10 sheets*l 4 11 x6 11 : up to 20 sheets Credit Card: up to 20 sheets Glossy Photo Paper Matte Photo Paper Letter: up to 10 sheets 4"x6": up to 20 sheets Lever Position for Media Type Left High Resolution Paper Left Plain Paper Left Glossy Photo Paper Left Matte Photo Pape
Basic Printing Wlrimm Printing with Windows W Note • • • The menu screens and dialog boxes that appear may vary depending on the application you are using. The steps described in this section are for printing using a computer with Windows® XP Service Pack 2 installed (hereafter called Windows XP SP2). You can use Easy-PhotoPrint to easily do print operations when printing photographs. Easy-PhotoPrint is provided on the Setup CD-ROM.
Basic Printing 4 Specify the required settings. (1) Click Media Type to select the media loaded in the printer. /)High ~. :~~~ ~::~d~rd C>£ustom CDA.!dto o Manual (2) Click OK. W S Note • From the Page Setup tab, select the correct document size to be printed. If the size is different from that set in the application, then you need to set it to the same size or use Scaled Printing or Fit-toPage. Refer to the Printer Driver Guide.
Basic Printing W Note You can cancel a print job in progress by simply pressing the Stop/Reset button on the printer. See "Cancel Printing" on page 15. Printing with Macintosh W Note • The menu screens and dialog boxes that appear may vary depending on the software application you are using. • The steps described in this section are for printing using a computer with Mac® as x v.l0.4.x installed (hereafter called Macintosh®).
Basic Printing 4 Specify the-required settings. (1) Select Print from the application1s File menu. The Print dialog box opens. 1------ (5) Select the print mode appropriate to your document listed under Print Mode. fc;;~:(_}- (6) Click Print. W Note • • • • • When you select the print mode appropriate to your document under Print Mode, the document will be printed in the color and print quality suited to the characteristics of the Media Type you have selected.
Basic Printing Cancel Printing (\fi¥~- .. You can cancel a print job while printing by pushing the Stop/Reset button on the printer. 1 Press the Stop/Reset button while the printer is printing. Printing is canceled and paper is ejected. W 1 Note You can also cancel a print job by clicking Cancel Printing on the Canon IJ Status Monitor. To display the Canon IJ Status Monitor, click Canon iP6320D/Canon iP6310D on the taskbar.
Basic Printing Accessing the Printer Driver (Windows) The printer properties dialog box can be opened from either within an application or directly from the Windows Start menu. W Note This manual refers to operations in Windows XP SP2. These operations may vary depending on the version of your Windows operating system you use.
Basic Printing Using the Bundled Software The Setup CD-ROM includes photo applications designed to edit the photographs taken by a digital camera and print them as photo-lab quality prints withou~ standard white borders. Use the application(s) suitable for your print purposes. W Note • • To install applications, refer to Easy Setup Instructions. For details about photo applications, refer to the Photo Application Guide.
Printing Maintenance Printing Maintenance When Printing Becomes Faint or Colors are Incorrect When printing becomes faint or colors are incorrect, the print head nozzles are probably clogged. Follow the procedures below to clean these nozzles. W Note Before Performing Maintenance Remove the FINE Cartridge once, then insert it into place again. Refer to "Replacing a FINE Cartridge" in the Direct Printing Guide. Step 1 Refer to "Printing the Nozzle Check Pattern" in the Direct Printing Guide. I;;;'.
Troubleshooting Troubleshooting This section provides troubleshooting tips for the most common printing problems. Troubleshooting usually falls into one of the following categories. Refer to the User's Guide for additional information on topics not covered in this section. When an error message is displayed on the LCD, refer to "An Error Message is Displayed on the LCD" in the "Troubleshooting" section of the Direct Printing Guide.
Troubleshooting Cannot Install the Printer Driver Problem Cannot Install the Printer Driver I Possible Cause Installation procedure not followed correctly I Try This Follow the Easy Setup Instructions packaged with your printer for proper printer driver installation. liiflrnmm If the installer was forced to be terminated due to an error, Windows may be unstable. Remove the CD-ROM from the CD-ROM drive and restart your computer. Reinstall the printer driver.
Troubleshooting Cannot Connect to PC Properly Problem Printing Speed Is Slow fUSB 2.0 HiSpeed Connection Does Not Work. I Possible Cause Your environment is not fully compatible with USB 2.0. Try This I If your environment is not fully compatible with USB 2.0, the printer will operate at a lower speed provided under USB 1.1. Check the following to ensure that your PC environment supports USB 2.0 HiSpeed connection. • The USB port on your PC supports USB 2.0 Hi-Speed connection.
Troubleshooting Print Quality is Poor or Contains Errors Problem Cannot Print to End of Job I Possible Cause Try This The Page Size setting does not match the size of the paper loaded in the printer First, check the Page Size setting in the application. Then, check the Page Size setting in the Page Setup tab of the printer driver for Windows or the Page Setup dialog box of the printer driver for Macintosh. '~'iilmmm Check the size of the print data.
Troubleshooting Problem I Possible Cause Incorrect paper type Try This I ('i'bmtm On the Main tab of the printer driver, ensure that the Media Type selected matches the media being used. Ifl~~m:mm In the Print dialog box of the printer driver, select Quality & Media from the pop-up menu, and then ensure that the Media Type selected matches the paper loaded. Glossy photo paper other than Canon genuine paper is used Select Other Photo Paper from Media Type, which may resolve the problem.
Troubleshooting Problem Printed Paper Curls or has Ink Blots I Possible Cause Paper being used is too thin I Try This Use photo paper such as Canon's Photo Paper Pro to print photos or pictures in deep color that have high color saturation. Incorrect paper type On the Main tab of the printer driver, ensure that the Media Type selected matches the media being used.
Troubleshooting Printer Does Not Start or Stops During Print Jobs Problem Printer Does Not Start or Printer Stops During Print Jobs I Possible Cause There may be problems with your operating system Try This I Restart your computer. It may solve the problem. Delete an undesired print job, if there is any. Use Canon IJ Status Monitor in Windows or Printer Setup Utility (or Print Center) in Macintosh for the deletion. i;irJmw!g 1. Open the printer properties dialog box.
Troubleshooting Paper Does Not Feed Properly Problem I Paper Does Not Feed Properly Possible Cause I Try This Inappropriate type of paper is being used • Paper feed roller is dirty Clean the paper feed rollers. Refer to "Back of Paper is Smudged/Paper Does Not Feed Properly/Printed Surface is Scratched" in the Direct Printing Guide. Paper is loaded incorrectly Load in the portrait orientation regardless of the print direction of the auto sheet feed. Ensure that paper is loaded correctly.
Troubleshooting An Error Message Appears on the Screen Problem r,,-,{, 'l.~ I Possible Cause I Try This Printer not ready Ensure that the POWER lamp lights. If the POWER lamp is off, turn the printer on. When the POWER lamp is flashing, the printer is initializing. Wait until the POWER lamp stops flashing. Paper is not loaded Load paper and press the OK button. An error message may appear if the "No paper" error has not been reset for a certain period.
Troubleshooting The printer has a built-in ink absorber to hold the ink used during print head cleaning, for example. This error message indicates that this ink absorber is nearly full. Press the OK button to clear the error so you can continue printing. Before the ink absorber becomes completely full, contact the Customer Care Center. When you experience this error, you will need to call for servicing to replace the ink absorber and to check the printer for proper operation. "Error No.
___________________________ At:lPendix Appendix Specifications Printer Maximum resolution (dpi): 4800 (horizontal)* x 1200 (vertical) *Ink droplets can be placed in a pitch of 1/4800 inch at minimum. Print speed * Black printing (text pattern) *Print speed will vary depending on system configuration, software, document complexity, print mode and page coverage. Max speed (custom setting 5): 12 ppm Standard: 3.4 ppm Color printing Max Speed (custom setting 5): 10 ppm Standard: 2.
Appendix Camera Direct Print (PictBridge) Paper size: Default (selections based on the printer setting), 10 x 15 cm/4 11 x 611 (Photo Paper Plus Glossy, Photo Paper Pro, Photo Paper Plus Semi-Gloss, Glossy Photo Paper, or Photo Sticker*1), 13 x 18 cm/S II x 711 (Photo Paper Plus Glossy)*2, A4/8.S 11 X 11 11 (Letter) (Photo Paper Plus Glossy A4/Letter, Photo Paper Pro A4/Letter, Photo Paper Plus Semi-Gloss A4/Letter, Glossy Photo Paper A4/Letter, or Plain Paper A4/Letter), S.4 x 8.
____________________________ AeJ?endix Minimum System Requirements *1 *2 Operating System Interface USB 2.0 Hi-Speed USB Hard Disk Space*4 RAM Processor 400MB 128MB Windows XP SP1, SP2 Pentium 111*3 Windows 2000 Professional SP4 (Celeron 566 MHz) Windows.XP SP1, SP2 Pentiumll 300 MHz*3 Windows 2000 Professional SP2, SP3, SP4 Windows Millennium Edition Windows 98, 98 Second Edition *2 Operating System Interface I USB 2.0 Hi-Speed USB Mac OS Xv.l0.4 Mac OS X v.l0.2.8 - v.l0.
~endix A Safety Precautions Please read the safety warnings and cautions provided in this manual to ensure that you use your printer safely. Do not attempt to use your printer in any other way than is described in this manual. Warning You may cause an electric shock/fire or damage the printer if you ignore any of ~hese safety precautions. Choosing a location Do not place the printer close to flammable solvents such as alcohol or thinners.
___________________________ AeJ?endix Caution You may cau~e injury or damage the printer if you ignore any of these safety precautions. Choosing a location Do not install the printer in a location that is unstable or subject to excessive vibration. Do not install the printer in locations that are very humid or dusty, in direct sunlight, outdoors, or close to a heating source.
Appendix Regulatory Information For 120V, 60Hz model Model Number: K10256 (iP6320D)/K10257 (iP6310D) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Appendix CANON U.S.A., INC. LIMITED WARRANTY ••• (USA Only) The limited warranty set forth below is given by Canon U.S.A., Inc. ("Canon USA") with respect to the new or refurbished Canon-brand product ("Product") packaged with this limited warranty, when purchased and used in the United States only.
~endix • Telephone Device for the Deaf (TDD-1-866-251-3752) • Repair or Exchange Service Options: In the event service is required for the Product during the limited warranty period, Canon USA offers two hardware support options: Authorized Service Facility Carry-In / Mail-In Service (anon USA's Carry-In/Mail-In Service provides repair or exchang.e, at (anon USA's option, through Canon USA's Authorized Service Facility (ASF) network.
Index Index A Opening the Printer Properties Dialog Box from your Application Program (Windows) Alarm lamp 2 An Error Message Appears on the Screen ............•........ 27 p B Page Setup (Macintosh) ......•...........•..•.•................•..... 13 Page Setup dialog box (Macintosh) ....•..............•...•..... 13 Paper feed roller ..•....••.•.•..•.•...•.......•..•.................••..... 26 Paper Size ......•..............•.....•................•..•.•.••....•........ 13 Paper Support Load limit ....
Index USB 2.0 Hi·Speed Using Specialty Media 21 9 w When Printing Becomes Faint or Colors are Incorrect ...
Ordering Information For additional supplies, use the following descriptions and order numbers. Description Order # FINE Cartridges CL-41 Color CL-51 Color CL-52 Photo 0617B002 0618Bo02 0 61 9 B002 Canon Specialty Papers 11 Photo Paper Plus Glossy (4 11 x 6 /20 sheets) Photo Paper Plus Glossy (4 11 x 6 11 /50 sheets) Photo Paper Plus Glossy (4 11 x 6 11 /120 sheets) Photo Paper Plus Glossy (5 11 x 7'1/ 20 sheets) Photo Paper Plus Glossy (8.
Quick Start Guide Canon U.S.A., Inc. One Canon Plaza, Lake Success, NY 11042, U.s.A. Canon Inc. 30-2, Shimomaruko 3-Chome, Ohta-ku, Tokyo 146-8501, Japan Canon Canada, Inc. 6390 Dixie Road, Mississauga, Ontario, LST 1P7, Canada Canon Latin America, Inc. 703 Waterford Way, Suite 400, Miami, FL 33126, U.s.A. Canon Mexicana Boulevard Man uel Avila Camacho No. 138 PB YPisos 15, 16 Y17, Colonia Lomas de Chapultepec Delegaci6n Miguel Hidalgo, CP 11000, Mexico D.F.
Canon .....
Canon PI}{MA iP6310D Photo Printer Direct Printing Guide
Contents Contents Operation Panel and Menu Display 3 Operation Panel Names and Functions ....•.•...•.•.•.•......••..•.•...•...•..•...•..•..3 LCD Monitor •.•.....•.••.•.......•....••.•.•..•.•.•...•.•...•..•...•........•....•.. 5 Memory Card Mode .............••.•..............•.•.•.•.•..........•.•...•.•..•.•.5 Configuration .•.••...•..•.......•.•.....•..••••....•.•.•....•...•.....•....•...... 6 Printing Flow 7 Using a Memory Card 9 Memory Cards Supported by This Printer ••••........•..•..•..........
Contents Replacing a FINE Cartridge 39 Replacing a FINE Cartridge .••••••..•.•........•••.....••.•..•..••...•.•.••........... 39 What is Low Ink Warning? ...•..•.•.•.•••..•...•.•..•••....••......•.....•...•...•...
Operation Panel and Menu Display The names and functions of the controls on the operation panel, how to display the menus, and the items in the menus are described below: Operation Panel Names and Functions (1) (3) (2) I II @j II • 1! 11 ~ 11-, (1) (4) (5) (6) (7) (8) (9) (10) (11) (12) POWER Button Press to turn the printer on or off. POWER Lamp Off: the printer is turned off. Lighting: the printer is ready to print, is currently printing, or is currently initializing.
(8) ....... Buttons Use these buttons to select a menu item or the number of photo, to specify the number of copies to print, and to make print settings. (9) OK Button Allows you to make a selection. For example, selecting a photo to be printed, selecting a menu item or other settings. If an error occurs, press to resume printing after resolving the printer problem. (10) Back Button Allows you to return to the previous screen.
LCD Monitor (1) Shows Memory Card Mode. (2) Shows the Media Type. (3) Shows the Page Size. [ INDEX] PHOTO PRO (4) Shows the number of photo in the memory card (only for INDEX printing). (5) The ...... buttons are activated when this mark is displayed. For the print settings of page size and media type etc. see the section of Memory Card Modes. Memory Card Mode When you press the Menu button, Memory Card Mode screens appear on the LCD. By using ...... button, you can select the following modes.
Configuration Each time you press Configuration button, following setting items are displayed on the LCD. PRINT SETTINGS QUIET MODE See "Other Settings" on page 23. WIRELESS SETTINGS PAGE SIZE MEDIA TYPE LAYOUT IMAGE OPTIMIZER See "Printing Photographs from a Wireless Communication Device" on page 29. BLUETOOTH SET DEVICE NAME ACCESS REFUSAL SECURITY PASSKEY See "Printing Photographs from a Wireless Communication Device" on page 29.
Printing Flow This is the procedure for printing photos from the memory card inserted in the card slot of the printer. Print a Photo List ofAll Photos in the Memory Cord Step 1 Turn on the Printer. Step 2 Load the paper. See "Loading Paper" on page 12. Step 3 Insert the memory cord. Step 4 Print a Photo List in the Memory Cord. See "Printing a Photo List - Print Index" on page 15.
Print the Photos by Other Printing Menus Select the photos you want to print in the printed photo list. Step 5 Select Memory Card Mode. PRINT ALL PHOTOS Prints all photos in the memory card. See "Printing All Photos" on page 20. SELECT PHOTO You can specify photos you want to print saved in the memory card. See "Specifying Photos to Print" on page 16. SELECT RANGE You can specify the range of photos you want to print using the file number or shooting date.
Using a Memory Card Let's take a look at different types of memory cards and how to insert and remove them. Memory Cards Supported by This Printer Supported memory cards are as follows: Memory Cards which can be inserted directly Memory Cards which can be used through a special adapter • • xD-Picture Card*l • CompactFlash (CF) Card Microdrive *Supports TYPE I/TYPE II (3.3V).
Inserting a Memory Card 1 Open the card slot cover. f ~~C ~~\~~~~~~~ \~ '~~-'~ f~~;?=~r-·_·~-.\ .._-.. 2 .. ~~ Insert the memory card in the card slot. • If you use a CompactFlash (CF) card or Microdrive In.ser~ it into th~ slo.t on the lower until it stops With Its end projecting as shown. ~~ ~ .4 : -~ ",,~ The indicator lamp lights. *For xD-Picture Card, use the compliant adapter.
3 Ensure that the indicator lamp lights after flashing for a moment and then close the card slot cover. W Notes • When OFF is selected in the READ-ONLY MODE screen, you cannot print photos in the memory card. After using the card slot as the memory card drive of the computer, remove the memory card, then be sure to select ON in the READ-ONLY MODE screen again. See "Setting up the Card Slot as the Memory Card Drive of the Computer" on page 34.
Loading Paper This section describes how to load the paper and select the page sizes and media types from the operation panel. • Print Media to Avoid Do not use the following types of paper. Using such paper will not only produce unsatisfactory results, but can also cause the printer to jam or malfunction.
2 Prepare to load paper. t"~---- (1) Open the paper support and the extension. ~~---:::~--(3) Set the paper thickness lever to the left position. (2) Pull out the paper output tray and the extension completely. 3 Load the paper. Load limit mark Do not load the stack of paper beyond this load limit mark. • II ~ (1) Insert the paper in the auto sheet feeder _~;.. ss .. ~ with print side facing UP. Load the pc;tper ~ lengthways regardless of the direction of t.\ the photo. .
• Media Types for Card Direct Printing You can use the following Canon genuine paper: Media Type Paper Support Load Limit PAGE SIZE Plain Paper A4/Letter: up to 100 sheets [A4]/[8.5"x11 11 Photo Paper Pro*1 A4/Letter: up to 10 sheets [A4]/[8.5"x11 11 101.6 x 152.4 mm/4" x 6": up to 20 sheets [4 x6"] A4/Letter: up to 10 sheets [A4]/[8.5"x11"] 101.6 x 152.4 mm/ 4" x 6 up to 20 sheets [4 x6"] 127 x 177.
Printing a Photograph Let's print a photo list of all photos in the memory card at first. Printing a Photo List - Print Index 1 Prepare to print. (1) Turn on the printer. (2) Load the paper. See "Loading Paper" on page 12. (3) Insert the memory card in the card slot. See "Inserting a Memory Card" on page 10. 2 Select the INDEX from the Memory Card Mode. (1) Press the Menu button. 1.MEMORY CARD MODE ~ INDEX)t-----;-~.;-----(2) Use the ~~ buttons to select INDEX 0 and then press the OK button.
4 Start Printing. Press the Print button. Specifying Photos to Print You can specify photos to print in the memory card. 1 Print a photo list. See "Printing a Photo list - Print Index" on page 15. 2 Select the SELECT PHOTO from the Memory Card Mode. (1) Press the Menu button. (2) Use the ~~ buttons to select SELECT PHOTO and then press the OK button. 3 Specify the photos to print. (1) Select the photo (the file number) from the printed photo list.
6 Check the print setting items. For the details of the print setting items, see "Print Setting Items" on page 22. PAGE SIZE: Use the <4lIII. buttons to select the page size and then press the OK button. MEDIA TYPE: Use the <4lIII. buttons to select the media type and then press the OK button. PRINTQLTY: Use the ~ ... buttons to select STANDARD or HIGH and then press the OK button. BORDERLESS PRINT**: Use the <4lIII.
Specifying the Range of Photos in the Memory Card You can specify the range of photos you want to print by the file number or shooting date. 1 Print a photo list. See "Printing a Photo List - Print Index" on page 15. 2 Select the SELECT RANGE from the Memory Card Mode. (1) Press the Menu button. (2) Use the ~~ buttons to select SELECT RANGE and then press the OK button. 3 Select the specification method. Use the ... ~ buttons to select PHOTO NO. or DATE and then press the OK button. PHOTO NO.
Printing on the Sticker - Sticker Print You can print your favorite photo on the Canon Photo Stickers. 1 Print a photo list. See "Printing a Photo List - Print Index" on page 15. 2 Select the STICKR from the Memory Card Mode. (1) Press the Menu button. (2) Use the ~~ buttons to select STICKR and then press the OK button. 3 Select a photo to print on the sticker looking at the printed photo list. (1) Select a photo (a file number) to print from the printed photo list.
Printing All Photos You can print all photos in a memory card. 1 Prepare to print. See "Printing a Photo List - Print Index" on page 15. 2 Select the PRINT ALL PHOTOS from the Memory Card Mode. (1) Press the Menu button. (2) Use the ~~ buttons to select PRINT ALL PHOTOS and then press the OK button. 3 Check the print setting items. 4 Start printing. See "Specifying Photos to Print" on page 16. Press the Print button.
1 Prepare to print. See "Printing a Photo List - Print Index" on page 15. 2 Select the DPOF from the Memory Card Mode. (1) Press the Menu button. (2) Use the .... ~ buttons to select DPOF and then press the OK button. 3 Check the print setting items. See "Specifying Photos to Print" on page 16. 4 Start printing. Press the Print button.
• Print Setting Items PAGE SIZE Select the page size. 8.5 xll", A4, 4 x6", 5 x7", CREDIT CARD SIZE I I I MEDIA TYPE Select the media type. PLAIN PAPER, PHOTO PAPER PRO, PHOTO PAPER PLUS, MAnE PHOTO PAPR, GLOSSY PRINTQLTY Select the printing quality. STANDARD, HIGH BORDERLESS PRINT Select bordered or borderless print. PRINT DATE Select whether to print the shooting date or not. FILE NO. PRINT Select whether to print the DCF (the file number) or not. IMAGE ENHANCEMENT Select SET or SKIP.
Other Settings Changing Other Settings • Quiet mode You can reduce the sound that the printer generates during operation. (1) Press the Configuration button to select QUIET MODE and then press the OK button. (2) Use the ~ .. buttons to select ON and then press the OK button. (3) Press the Stop/Reset button. ~Important • Print speed may be somewhat slower than in the normal operating mode. • • Sound reduction is not as effective when certain printing options are selected.
Printing Photographs Directly from a Digital Camera Printing Photographs Directly from a PictBridge Compliant Device Connecting a PictBridge compliant device such as digital camera, camcorder or mobile phone to the printer allows you to print recorded images directly without using a computer.
WNote Depending on the model or brand of your PictBridge compliant device, you may have to select a print mode before connecting the device. You may also have to turn on the device or select Play mode manually after connecting the device to the printer. Perform necessary operations according to the instruction manual supplied with your device. (1) Ensure that the device is turned off. (2) Connect the camera to the printer using the USB cable (for connection to a computer) supplied with the device.
• Confirming or Changing the Device Settings To change the paper size or paper type, operate the device to select the PictBridge print setup mode and confirm or change the settings. You can change the following settings on the PictBridge setting screen displayed by pressing Configuration button. However, changes can be made on the PictBridge setting screen only when the corresponding items below are in the Default (selections based on the printer setting) using the controls of the device.
The following sizes and types of paper can be loaded in the printer by selecting options from Paper Size and Paper Type.
• About "Image optimize" When you have selected Default (selections based on the printer setting), the printer operates based on the PictBridge setting screen. If you use a Canon PictBridge-compliant device, you can select VIVID, NR, VIVID+NR, or Face. (Note that these options cannot be selected for some models.) WNotes • When VIVID is selected, green and blue portions of photos are printed vividly.
Printing Photographs from a Wireless Communication Device This section explains the printer's settings when printing photos through Bluetooth communication. If the optional Bluetooth unit BU-20 is connected to the printer, you can also print photos through Bluetooth communication. For details, refer to the Bluetooth User's Guide. WNote • The mobile phone supporting the opp (Object Push Profile) or BIP (Basic Imaging Profile) can print photos.
3 Press the Configuration button repeatedly to select the WIRELESS SElTlNGS and then press the OK button. 4 Confirm or change the settings. (1) Use the -4 .. buttons to select the item to set and then press the OK button. The photos in the mobile phone can be printed according to the following settings. • Setting Items PAGE SIZE: Select the page size for the wireless print. MEDIA TYPE: Select the media type for the wireless print.
Performing Bluetooth Communication • Printing through Bluetooth communication When you print through Bluetooth communication from a mobile phone, refer to your mobile phone manual. 1 Prepare to print. (1) Confirm the printer is ON. (2) Load the paper in the auto sheet feeder See "Loading Paper" on page 12. 2 Connect the Bluetooth unit BU-20 to the direct print port. 3 Set the print setting. See "Setting the Page Size, Media Type, and Layout When Printing From a Mobile Phone" on page 29.
About transmittable data • It does not support printing a downloaded content or photo and a photo attached to an E-mail for security reason. • It does not support printing video files. • Depending on your device, it may not print data stored in a memory card. • Depending on the size of a photo, it may take a while for this printer to start to print after starting the infrared transfer. • It automatically sets the photo quality and orientation (horizontal or vertical) according to the photo size.
Using Data in the Memory Card on the Computer Browsing Photos in the Memory Card on the Computer By pressing the Easy~PhotoPrint Startup button, you can display photos in the memory card on the computer display with Easy-PhotoPrint, if the printer is connected to the computer. You can print the photos from Easy-PhotoPrint. ~Important To use the Easy-PhotoPrint Startup button, connect the printer to the computer and install the printer driver, Memory Card Utility, and EasyPhotoPrint.
Windows XP/Windows 2000/Windows Me: My Pictures folder Windows 98: My Documents folder Mac as x v.10.2.8 or later: Pictures folder Setting up the Card Slot as the Memory Card Drive of the Computer The card slot of the printer can also be used as the memory card drive of the computer.
Printing Maintenance When Printing Becomes Faint or Colors are Incorrect When printing becomes faint or colors are incorrect, the print head nozzles are probably clogged. Follow the procedures below to clean the nozzles. WNole Before Performing Maintenance Remove the FINE Cartridge once, then insert it into place again. See "Replacing a FINE Cartridge" on page 39. Step 1 "AD~rua__~~..,,~~~~~ __~ ~ "Printing the NOlzle Check Pattern" on page 36 Step 2 .W~ 1'*4. . . . . . . .
Printing the Nozzle Check Pattern Print the nozzle check pattern to determine whether the ink ejects properly from the print head nozzles. Use this function when printed results are blurred or the colors are incorrect. 1 With the printer on, load a sheet of A4/Letter-sized plain paper in the auto sheet feeder. Move the paper thickness lever to the left position. 2 Print the nozzle check pattern. (1) Press the Configuration button repeatedly to select MAINTENANCE. (2) Use the ...
Print Head Cleaning If white stripes are found in the printed nozzle check pattern, perform the print head cleaning to unclog the print head nozzles. Cleaning the print head consumes ink, so perform the print head cleaning only when necessary. 1 Ensure that the printer is on. 2 Start print head cleaning. (1) Press the Configuration button repeatedly to select MAINTENANCE. (2) Use the ... ~ buttons to select CLEANING and then press the OK button.
Print Head Deep Cleaning If print quality does not improve by the standard print head cleaning, try print head deep cleaning, which is a more powerful cleaning process. Print head deep cleaning consumes more ink than standard print head cleaning, so perform this procedure only when necessary. 1 2 Ensure that the printer is on. Start print head deep cleaning. (1) Press the Configuration button repeatedly to select MAINTENANCE. (2) Use the ... buttons to select DEEP CLEANING and then press the OK button.
Replacing a FINE Cartridge If there is no improvement with the quality of printing following such maintenance as print head cleaning, a FINE Cartridge is probably empty. Replace the empty FINE Cartridge with a new one. When replacing a FINE Cartridge, check the model number very carefully. The printer will not print properly if a wrong FINE Cartridge is used, or installed wrong.
4 Prepare a replacement FINE Cartridge. * ."" ~---Protectivetape *To the FINE Cartridge holder Unpack a new FINE Cartridge and remove the orange protective tape gently. ~Important • • • 5 Do not reattach the protective tape once you have removed it. Handle the removed protective tape carefully to avoid getting your hands dirty or staining surrounding work area. Once the protective tape is removed, do not touch the electrical contacts or print head nozzles on a FINE Cartridge.
6 Close the front cover first and then close the card slot cover. The FINE Cartridge holder moves to the right. WNote ~Important If straight lines are misaligned or the resulting output is unsatisfactory, align the print head position. See "Aligning the Print Head - Auto head align" on page 38. • To maintain optimal print quality, we recommend that you use Canon brand FINE Cartridge. Replenishing ink only is also not recommended. • Replace the FINE Cartridge promptly.
What is Low Ink Warning? The low ink warning is that the ink counter counts a remaining level of ink and tells you that FINE Cartridges are running out of ink before printing. The ink counter considers as ink is full when new FINE Cartridge is installed, and then starts counting a remaining level of ink. For this, if old FINE Cartridge is installed, a remaining level of ink cannot be displayed correctly.
Troubleshooting Let's take a lool< at countermeasures against troubles which may occur during use of the printer. WNote Here, we will discuss errors indicated on the LCD, problems that might occur during direct printing from the digital camera. If you cannot find the symptom corresponding to a certain problem, refer to the User's Guide.
Message I Try This INCOMPATIBLE CAMERA Disconnect the camera cable and reconnect it. Depending on the model or brand of your PictBridge compliant device, you may have to select a print mode before connecting the device. You may also have to turn on the device or select Play mode manually after connecting the device to the printer. Perform necessary operations according to the instruction manual supplied with your device.
• POWER Lamp and Alarm Lamp Flash Alternately Possible Cause I An error that requires contacting the Customer Care Center may have occurred Try This Disconnect the printer cable from the printer, and then turn the printer off and unplug the printer from the power supply. Plug the printer back in and turn the printer back on after leaving it for a while. If the problem remains, contact the Customer Care Center.
• Back of Paper is Smudged/Paper Does Not Feed Properly/Printed Surface is Scratched Possible Cause I Inside of the printer is dirty Try This If the inside of the printer is dirty, printed paper may be smudged. Follow the steps described below to clean the inside of the printer. (1) Ensure that the printer is turned on and there is no paper loaded in the auto sheet feeder. (2) Place A4/letter-sized plain paper in landscape, horizontally fold it in half.
Possible Cause Inappropriate media type is used I Try This • Check to see if the paper you are printing on is too thick. See "Print Media to Avoid" on page 12. • Note that smudging may occur at the top and bottom edges of the paper when using borderless printing. Ensure that the paper you are using is compatible with borderless printing. If all four corners or the printing surface of the paper is curled, the paper may become dirty or not feed properly through the printer.
• Paper Jams Possible Cause I Try This Landscape credit card-sized paper jams inside the printer You cannot load credit card-sized paper in the landscape orientation. Slowly pull the paper out from the auto sheet feeder. Paper jams in the paper output slot Remove the paper according to the following procedure. (1) Slowly pull the paper out, either from the auto sheet feeder or from the paper output slot, whichever is easier.
• Cannot Print Properly from the Digital Camera The following are the possible errors that may occur when printing directly from a digital still camera or digital video camcorder*, and the countermeasures to eliminate them. * Hereafter, the digital still camera and digital video camcorder are collectively called a digital camera or camera. WNote This section describes errors that are indicated on Canon-brand PictBridge-compatible cameras.
Error message on camera Try This I Noink Possible causes are as follows: • The ink has run out. Replace the FINE Cartridge, and close the front cover. If lines are misaligned or the resulting output is not satisfactory, carry out the print head alignment. If printing is in progress and you want to continue printing, press the OK button on the printer. Then printing can continue under the ink out condition with the FINE Cartridge installed. Replace the empty FINE Cartridge immediately after the printing.
WNotes • PictBridge-compatible digital cameras can be connected to your printer • • • • • • for direct printing. A communication time out occurs if printing takes a long time or if it takes too much time to send data. This may stop printing. In such a case, disconnect the cable between the printer and the camera, and reconnect it. Then, turn the camera on, if it does not automatically turn on just by connecting the cable.
Index Index A Adjusting the Print Head Manually 44 Alarm Lamp •.....•.............................................•............. 3 ALIGN PRINT HEAD .•.........•..•.•..•.........•.....................6, 44 38 Aligning the Print Head AUTO HEAD ALIGN ............•............•.•....•.......•......•... 6, 38 Auto sheet feeder 12 B BlUETOOTH SET ......•..............••...•....•..•..•.••.••.••.•..•....... 6 BORDERLESS PRINT ..................•........•......•................. 22 BORDERLESS PRINT (PictBridge) ..
Index Printing All Photos Printing is Blurred Printing Maintenance Printing on the Sticker - Sticker Print 20 45 35 19 Q QUIET MODE 6,23 R READ-ONLY MODE RED EYE CORR REMOVE NOISE RESTORE DEFAULT ROLLER CLEANING 6 22 22 6,23 6,46 5 Save Button SAVE CONFGURATION SELECT PHOTO SELECT RANGE Specifying Photos to Print Specifying the Range of Photos in the Memory Card STICKR 3,33 6, 17 5, 16 5, 18 16 18 5. 19 T Trimming (PictBridge) 27 v VIVID 22 w White Streaks WIRELESS SETTINGS 45 6.
54
Direct Printing Guide (anon U.S.A., Inc. One Canon Plaza, Lake Success, NY 11042, U.S.A. Canon Inc. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan (anon Canada, Inc. 6390 Dixie Road, Mississauga, Ontario, L5T 1P7, Canada (anon latin America, Inc. 703 Waterford Way, Suite 400, Miami, FL 33126, U.S.A. (anon Mexicana Boulevard Manuel Avila Camacho No. 138 PB y Pisos 15, 16y 17, Colonia Lomas de Chapultepec Delegaci6n Miguel Hidalgo, CP 11000, Mexico D.
Carefully remove all items from the box. o Remove the shipping tape from the front and back of the printer. fJ Open (a) the card slot cover first and (b) the front cover next, Pull down and remove the protective material on the right side. (a) Card slot cover PIXMA iP6310D Photo Printer (b) Front cover Power Cord Protective material • Close the front cover first and the card slot cover next. e Plug the power cord into the back of the printer and connect the other end to a power outlet.
o Take out the Color FINE Cartridge (Cl-41) from its box and remove the protective o Open the paper support and pull out the paper output tray. tape gently. Paper support Electrical contacts Protective tape W NOTE: -Do not touch the electrical contacts or print head nozzles on a FINE Cartridge. The printer may not print out properly if you touch it. -Do not reattach the protective tape once you have removed it.
The screens below refer to Windows XP Service Pack 2 installation. Screens may differ depending on the operating system you are using. • When the Printer Connection screen appears, connect the USB cable to the computer and the other end to the printer. o TURN THE PRINTER OFF. You hear the operation sound until the printer is turned off. It may take about 20 seconds. f) Turn the computer on and start Windows.
~ ~ & When the Easy Install screen appears, click Install. NOTE: -Before installing the driver, disable all anti-virus programs and automatically loading programs. Easy Install -Use Mac®OS X v.l0.2.8 to 10.4.x. -The screens below refer to Mac OS X v.l0.4.x installation. Screens may differ depending on the operating system you are using. 1~?!MemorycardUtillty -Do not remove or insert the USB cable during installation, as this may result in the computer or printer not operating normally.
........... %:.ifii~W'li&ifiiilHL~~ photography Print/Share Button Printing without a computer just got even easier! First, connect a Canon PowerShot camera with the advanced Print/Share* button to a PictBridge compatible printer. Then, with the desired image displayed on the camera's LCD (in playback mode), press the Print/Share button. In seconds you'll have a brilliant photograph of that image. How easy was that? * For a list of Canon cameras featuring a Print/Share button, visit www.usa.canon.
A System for Long-lasting Photos. The Canon ChromaLifel00 system combines the FINE print head technology and newly developed inks with select Canon photo papers, with results rivaling that of many conventional photos. Lil
Product registration valid only in the U.S.A. Canon I PIXMA™ iP6310D Photo Printer Registration Card I Thank you for purchasing aCanon PIXMA iP631 00 Photo Printer. To help us selVe you better, complete and return this Registration Card. Simply fill out the following questions and mail this card or fax it to 1-800-567-3229. Note: The toll-free number is for Registration Cards only. No operator will answer this number. o Mr. Q] V1PIP6310 0 Ms. ,--I...l...--L----L---l..-JL......L---'---'------J...
NO POSTAGE NECESSARY IF MAILED INTHE UNITED STATES Please send correspondence to: Canon U.s.A., Inc. One Canon Plaza Lake Success, NY 11042·1198 BUSINESS REPLY MAIL FIRST-CLASS MAIL PERMIT NO. 10331 SALT LAKE CITY UT POSTAGE WILL BE PAID BY ADDRESSEE CANON USA INC DEPT PIXMATM iP6310D PO BOX 30403 SALT LAKE CITY UT 84130-9776 11111111 •• 111 .11 •• 11. 1111.1.1 •• 1. 1111. 111.1111 .1. 1.1 Fold Here Registration Card Congratulations on purchasing a Canon PIXMA™ iP6310D Photo Printer.
