General Timing Chart / General Circuit Diagram Finisher, Sorter, DeliveryTray Finisher-Q1/Q3 Feb 1 2005
IMPORTANT This documentation is published by Canon Inc., Japan, to serve as a source of reference for work in the field. Specifications and other information contained herein may vary slightly from actual machine values or those found in advertising and other printed matter. Any questions regarding the information contained herein should be directed to the Copier Service Department of the Sales Company.
Contents 1 Genelal Timing Chart ............................................................................................................................................... 1 Finisher Unit............................................................................................................................................................ 1 2 General Circuit Diagram .......................................................................................................................................
1 Genelal Timing Chart Finisher Unit Stapling : A4 size paper, 2-sheet document, rear1-point stapling Operation start signal Host machine eject signal Operation 1 Inlet sensor (PI33) 2 Feed path sensor (PI34) 3 Inlet motor (M31) 4 Stack ejection roller (M32) 5 1st delivery roller alienate solenoid (SL33) 6 Stack ejection lower roller clutch (CL32) 7 Swing motor (M36) 8 Swing unit home position sensor (PI35) 9 Front aligning plate motor (M33) 10 Front ligning plate home position sensor (PI
2 General Circuit Diagram Signal Names List of Signal Names/Abbreviations (Finisher Unit) The following presents the abbreviations of signals used in this manual and in drawings, and the meaning of each signal. Reference: Signals enclosed by brackets [ ] are electrical signals, However, the state "1" or "0" of these analog signals cannot be indicated. Otherwise, the state of digital signals "1" or "0" can be indicated.
TIMMING FEED PLATE PASS PAPER DETECT Signal TRY1- TRAY 1 AREA DETECT Signal 1 AREA1 TRY1- TRAY 1 AREA DETECT Signal 2 AREA2 TRY1- TRAY 1 AREA DETECT Signal 3 AREA3 TRY1-P TRAY 1 PAPER DETECT Signal TRY2- TRAY 2 AREA DETECT Signal 1 AREA1 TRY2- TRAY 2 AREA DETECT Signal 2 AREA2 TRY2- TRAY 2 AREA DETECT Signal 3 AREA3 TRY2-P TRAY 2 PAPER DETECT Signal TRYSFT2- TRAY 2 PAPER SURFACE DETECT Signal P UP- UPPER COVER OPEN/CLOSE DETECT Signal COVER UPPER-P PAPER SURFACE DETECT Signal UPPER-
General Circuit Diagram Finisher Unit General Circuit Diagram(1/2) Swing guide home position sensor PI35 Feed path sensor Front cover sensor PI34 PI32 Gear change motor M40 Gear change home position sensor Upper cover sensor Inlet sensor PI49 PI31 PI33 Swing motor Inlet motor Stack ejection motor M36 M31 M32 M M M M J1001 3 2 1 3 2 1 3 2 3 J1002 2 1 1 J1003 3 2 1 3 2 1 4 J1004 4 3 3 Buffer rear end holding solenoid 1st delivery roller alienate solenoid Buffe
Finisher Unit General Circuit Diagram(2/2) M41 M35 M38 1 6 5 2 4 PI46 M M Tray 2 shift motor Stapler alignment interference sensor Staple motor Stapler shift motor 3 3 2 1 3 2 4 2 1 J1027 J1028 4 1 1 2 3 4 5 3 2 1 1 2 3 J1029 J1030 M 3 11 16 13 15 1 3 5 17 1 2 3 4 5 6 5 4 3 2 1 +5VR S-GND 3 4 5 6 7 8 9 10 11 12 13 14 15 J717 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 11 3 10 4 9 5 8 6 7 7 6 8 5 9 4 10 3
Feb 1 2005
