Service manual

Chapter 13
13-2
E001 0000 Abnormally high temperature (detected by main thermistor)
The main thermistor detected an
abnormally high temperature (240 deg
C) during temperature control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
0001 Abnormally high temperature (detected by sub thermistor)
The sub thermistor detected an
abnormally high temperature (295 deg
C) during temperature control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E002 0000 Low temperature during temperature control.
The target temperature is not reached
during temperature control.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E003 0000 Abnormally low temperature (detected by main thermistor)
After the temperature detected by the
main thermistor has reached the
specified value, it does not reach the
specified value during initial rotation.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
0001 Abnormally low temperature (detected by sub thermistor)
After the temperature detected by the
sub thermistor has reached the
specified value, it does not reach the
specified value during initial rotation.
- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the DC controller PCB.
E007 0000 Fixing film sensor failure
The fixing film sensor is faulty. - Check the connector of the fixing film
sensor.
- Replace the fixing film sensor.
- Replace the DC controller PCB.
E010 0000 Main motor failure
The main motor is faulty. - Check the connector of the main motor.
- Replace the main motor.
- Replace the DC controller PCB.
E019 0000 Waste toner full detection
The waste toner full state was detected. Replace the drum unit.
0001 Waster toner full detection sensor is faulty.
The waste toner full state was detected
continuously for five or more seconds
while the main motor was turning.
- Check the connector of the waster toner full
sensor.
- Replace the waste toner full sensor.
- Replace the DC controller PCB.
E052 0000 Erroneous connection to duplex unit
Disconnection of the duplex unit was
detected after power-on, detection of
normal connection to the duplex unit,
and start of communication.
- Check the connectors of the duplex unit and
DC controller PCB.
- Replace the duplex controller PCB.
- Replace the DC controller PCB.
E100 0000 BD detection PCB failure
The BD detection PCB is faulty. - Check the connector of the BD detection
PCB.
- Replace the laser scanner unit.
- Replace the DC controller PCB.
E197 0000 Printer engine communication error
Erroneous communication between the
DC controller PCB and image
processor PCB was detected.
- Check the connectors of the DC controller
PCB and image processor PCB.
- Replace the DC controller PCB for normal
connection.
- Replace the image processor PCB.
E716 0000 Erroneous communication with optional cassette
Disconnection of the optional cassette
was detected after power-on, detection
of normal connection to the optional
cassette, and start of communication.
- Check the connectors of the optional cassette
PCB and DC controller PCB.
- Replace the optional cassette PCB for
normal connection.
- Replace the DC controller PCB.
E719 0000 Erroneous communication with card reader (serial communication)
- Disconnection from the card reader
has been detected since
communication started after
confirmation of normal connection to
the card reader (after power-on).
- A serial communication error has
occurred. (The serial communication
error cannot be recovered.)
- Check the connectors of the card reader and
image processor PCB.
- Replace the card reader for normal
connection.
- Replace the image processor PCB.
0002 Erroneous communication with coin vendor (serial communication)
- Disconnection from the coin vendor
has been detected since
communication started after
confirmation of normal connection to
the coin vendor (after power-on).
- A serial communication error has
occurred. (The serial communication
error cannot be recovered.)
- Check the connection between the image
processor PCB and serial PCB.
- Check the connectors of the serial PCB and
coin vendor for normal connection.
- Replace the serial PCB.
- Check the coin vendor.
- Replace the image processor PCB.
Display
Code
Detail Code Main Cause/Symptom Countermeasure