Service manual

Chapter 13
13-2
13.2 Jam Code
13.2.1 Jam Codes (Main body)
0011-7062
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
T-13-2
13.2.2 Jam Codes (ADF)
0011-7059
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
T-13-3
13.3 Fax Error Codes
13.3.1 Outline
13.3.1.1 Error Code Outline
0012-5780
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
An error code is used to indicate a fault in a machine, and is indicated in the machine's LCD or reports, showing the nature (symptoms) of the fault. Using the error
code, the user or the service man can readily find out how to correct the fault by simply referring to the User's Manual or service manual.
An error code may be either of the following two types:
User Error Codes
A fault indicated as a user error code is one that can easily be corrected by the user, as by operating the machine. It takes the form of "#+number."
Service Error Codes
If a fault calls for a service man for correction, it is indicated as a service man error code in the form of "##+number" or "SYSTEM ERROR E+number."
Memo
A service error code expressed in the form of "##+number" will not appear on the LCD, Error Tx Report, or Activity Report while the machine remains
in factory default state. To check a service error code, shift bit 0 of service soft switch #1 SSSW SW01 to '1'.
Memo
Display only the error codes which are newly incorporated in this machine as well as which require remedies unique to the product. For the causes and
countermeasures of other error codes, refer to the separate G3/G4 Facsimile Error Code List (Rev. 2).
13.3.2 User Error Code
13.3.2.1 User Error Code
0012-5781
LaserBase MF6530 / / LaserBase MF6540PL / LaserBase MF6550 / KaserBase MF6560PL / / LaserBase MF6580PL
T-13-4
Code Name Sensor No. Description
0104 Delay jam in paper pickup
section
SR11 The registration sensor cannot detect the leading edge of paper from the moment paper pickup starts
to the moment the jam detection time is reached.
0208 Stationary jam in paper
pickup section
SR11 The registration sensor cannot detect the no paper status specified time before the leading edge of
the picked up paper reaches this sensor.
010c Delay jam in deliver section SR5 - The delivery sensor cannot detect presence of paper within the specified time after turning on of
the registration clutch.
- The delivery sensor detected absence of paper within the specified time after the sensor had
detected presence of paper within the specified time after turning on of the registration clutch.
0210 Stationary jam in delivery
section
SR5 - The delivery sensor cannot detect absence of paper within the specified time after turning off of
the registration clutch.
- The delivery sensor cannot detect absence of paper within the specified time after the sensor
detected the leading edge of paper.
0214 Stationary jam in machine SR5, SR9 Paper was detected in the paper transport path during initial rotation, during automatic delivery, at
the end of cleaning, or at reception of an emergency stop command.
1118 Door open jam SW2, SR5, SR9,
SR11
The door was opened when there was printing paper in the transport path.
Code Name Sensor No. Description
0000 Unknown jam - Other errors
0007 Initial stationary SR2002, SR2003, SR2004 Paper is detected in the transport path before the DADF starts initial
operation.
0008 Document edge sensor
delay
SR2002 The document edge sensor does not detect paper when the paper has been fed by the
predetermined distance since reception of a pickup request.
0009 Document edge sensor
stationary
SR2002 The trailing edge of paper is not detected when the paper has been fed by the
predetermined distance since detection of it by the document edge sensor.
000a Paper absence (Pull out
the document.)
SR2001 The Document set sensor has been held off since start of pickup.
0010 Pickup NG SR2003 The registration sensor has been held off since paper pickup started.
No. Tx/Rx Description
#0001 [Tx] an original has jammed.
#0003 [Tx/Rx] tine-out for copying or sending/receiving a single page has occurred.
#0005 [Tx/Rx] time-out for initial identification (T0/T1) has occurred.
#0009 [Rx] recording paper has jammed or is absent.
#0012 [Tx] recording paper is absent at the other party.
Download Free Service Manual And Resetter Printer at http://printer1.blogspot.com