9155 Network Interface Device User Manual
CAUTION! This product may contain a laser diode operating at a wavelength of 1300nm - 1600nm. Use of optical instruments (e.g., collimating optics) with this product may increase eye hazard. Use of controls or adjustments, or performing procedures other than those specified herein may result in hazardous radiation exposure. Under normal conditions, the radiation levels emitted by this product are under Class 1 limits in 21 CFR Chapter 1, Subchapter J.
NOTICE Canoga Perkins has prepared this users manual for use by customers and Canoga Perkins personnel as a guide for the proper installation, operation and/or maintenance of Canoga Perkins equipment. The drawings, specifications and information contained in this document are the property of Canoga Perkins and any unauthorized use or disclosure of such drawings, specifications and information is prohibited.
Table of Contents Chapter 1 Overview .................................................................................................1-1 Chapter 2 Set-up and Installation ..........................................................................2-1 2.1 2.2 Install the 9155 ........................................................................................................................2-1 Measure Fiber Link Attenuation and Transmit Power ............................................................
Chapter 5 Maintenance and Troubleshooting ...................................................... 5-1 5.1 General Maintenance .............................................................................................................. 5-1 5.2 Manage Cable Links ............................................................................................................... 5-1 5.3 Check Optical Power Levels...................................................................................................
List of Figures Figure 1. The 9155 Front Panel..........................................................................................................1-1 Figure 2. Remote Fault Signal............................................................................................................3-3 Figure 3. Link Loss Forwarding Propagation.....................................................................................3-3 Figure 4. General Screen Format.....................................................
List of Tables Table 1. 9155 Management LEDs ..................................................................................................... 3-1 Table 2. 9155 Interface LEDs ............................................................................................................ 3-2 Table 3. System Menu Option Definitions ........................................................................................ 4-4 Table 4. IP Settings Definitions .....................................................
Chapter 1 Overview The 9155 is a 12-Port Aggregator Network Interface Device that provides intelligent optical demarcation and terminates managed transport at the point of delivery as it supports 802.3ad link aggregation. The 12 modular ports support 10/100/1000 Mbps Ethernet in fiber or copper. In addition, the 9155 offers Layer 2 statistics, local and remote loopback, remote software upgrade, remote control and monitoring, and management through CanogaView.
1-2 9155 Network Interface Device
Chapter 2 Set-up and Installation This section describes how to set up and install the 9155 and the interface modules. Before setting up the 9155, make sure the serial cable (required to connect the chassis to a VT100 type terminal or PC) is available. 2.1 Install the 9155 The 9155 is tested and inspected before shipment from the factory. If there is obvious damage to the shipping container, contact the carrier immediately.
Cabling for the 9155 includes the serial cable to the Terminal port, the Ethernet cable for a UTP port, and the fiber optic link to the Tx and Rx ports. 5. Plug the serial cable into the SLIP or Terminal port on the rear panel and your PC. For the pinouts, see Chapter 5, Specifications. • • The EIA 232 Terminal port provides serial access to the management software. The SLIP port provides serial or modem access to the management software.
Chapter 3 User Operation This chapter describes the hardware features and functions of the 9155. 3.1 9155 Functions, and Power-Up, and LEDs During the initial power-up sequence, all LEDs light amber. When start-up is complete, the setup and installation are correct, and data is transmitting normally across the link, the MGR LED lights green and the LNK, Rx, or Tx LEDs for all active ports light green or blink green when they transmit or receive data. See Tables 1 and 2.
Table 2. 9155 Interface LEDs LED Tx Rx NET SPD LNK 3.
Usr Prt Ext Prt Tx Rx Rx Tx Ext Prt RMTF Local Device • • • • Usr Prt Tx Rx Rx Tx Local device Rx detects link loss Tx transmits RMTF to remote device Local device Rx turns OFF Remote device Rx lights red Remote Device Figure 2. Remote Fault Signal 3.2.2 Link Loss Forwarding When LLF is enabled, a fault on one side of the 9155 propagates to the other side to notify that device and stops signal transmission (brings down the link). See Figure 3.
3-4 9155 Network Interface Device
Chapter 4 Management - VT-100 You can manage the system through VT100 Terminal Emulation, which is accessible by a Telnet session, HyperTerminal or similar terminal emulation software, a standard SNMP network manager, and CanogaView. 4.1 VT100 Terminal Emulation Setting up the VT100 session depends on which connection, serial port or Ethernet, you have available for access to the VT100 management program. Canoga Perkins suggests that you use HyperTerminal for your first session.
4.3 Management User Interface The Management User Interface for the 9155 provides screens for setup, monitoring, and diagnostics. You can access the screens directly by connecting to the serial port of the 9155 These sections discuss the screens for the 9155, using a Telnet session for access. 4.3.1 General Screen Format A typical screen, shown in Figure 4, includes standard descriptions and reference designations.
Main Menu 1) System 1) System Information 2) Module Information 3) IP Settings 6) Static ARP Table 7) Dynamic ARP Table 4) Host Access Table 5) Notification Destination Table 6) Security Configuration 7) User Accounts 8) Management Packets Filter 9) Trap Configuration 10) SNTP Settings 2) Switch Configuration 1) Global Spanning Tree Parameters 2) MST Instance Configuration 3) Global Spanning Tree Report 4) Lag Configuration 5) VLAN Configuration 6) GVRP Information 3) Port Information 1) XP x Information 2)
4.4 9155 Main Menu The first screen is the Login Menu. If this is your initial setup and no password has been set, press at the prompt for the password. Otherwise, type your password and press . The Main Menu appears after you log in and provides access to all functions for the 9155: setup, diagnostics, and reports. See Figure 5. 1) 2) 3) 4) 5) 6) 7) MAIN MENU System Switch Configuration Port Information Reports Diagnostics Utilities Logout Figure 5. 9155 Main Menu 4.
Selection Description 4. Host Table/SNMP Settings Shows host access IP information; you can set options 5. Notification Settings Shows information for hosts that will receive traps and alarms; you can set options 6. Security Configuration Shows parameters for passwords, lockout, and logout; you can set options 7. Account Configuration Shows user account information; you can set options 8. Management Packets Filter 9. Trap Configuration 10. SNTP Settings 12. Main Menu Returns to the Main Menu 4.
4.5.2 Module Information Screen The Module Information report provides status for the 9155 and the installed modules.
Table 4.
To view the current addresses, follow these steps: 1. From the IP Settings screen, type 7, "Dynamic ARP Table," and press . 2. To return to the IP Settings screen, press . 4.5.4 Host Access Table Screen The SNMP agent allows access to up to 24 Host IP addresses. Set up and edit the Host information for the 9155 at the Host Access Table screen. See Figure 12. To access the Host Access Table, follow these steps: 1. From the System menu type 3, "Host Table/ SNMP Settings," and press . 2.
Managing Host 172.16.14.200 172.16.100.20 172.16.142.1 Port 163 162 163 1. 2. 3. 4. NOTIFICATION DESTINATION TABLE Username/ Security Type Community Level V1-Trap public N/A V2c-Trap public N/A V3-Trap public Auth/No Priv View/Change Host Create Host Delete Host Main Menu Figure 13. Notification Destination Table Screen 4.5.6 Security Configuration Screen The Security Configuration menu provides options to set values for general parameters for passwords, lockout, and logout.
Table 5. Security Configuration Option Definitions Menu Item Description 1. Minimum Length 2. Minimum Alpha Characters 3. Minimum Numeric Characters 4. Minimum Punctuation Characters 5. Maximum Consecutive Character Types 6. Maximum Same Character Define characteristics of passwords; the range for all fields is from 0 through 15 7. Allow username in password Enable or disable the username appearing as or within the password 8.
Username admin Account State Enabled USER ACCOUNTS Access Access Auth Priv Lockout Locked From Level Description Proto Proto User Out All Supervisor Default Account None None No No 1. 2. 3. 4. View/Change Account Create Account Delete Account Main Menu Figure 15. User Accounts Screen 4.5.8 Management Packets Filter Screen Use the Management Packets Filter screen to enable or disable transmission of management packets through any specific port on the 9155.
4.5.9 Trap Configuration Screen Use the Trap Configuration screen to enable or disable traps on the 9155. To access the Trap Configuration screen, see Figure 17 and follow these steps: 1. From the System menu type 9, "Trap Configuration," and press . 2. At the Trap Configuration screen, type the number for a port, then press to cycle between Enabled or Disabled. 3. To return to the System menu, press . 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
Table 6.
1 A 3 D B 6 E 3 C 4 1 A 2 5 D A small test network B 2 C 4 6 E 5 Spanning Tree from source (C) Figure 20. Typical Spanning Tree Application. Note: For details on the Spanning Tree Algorithm, see the IEEE 802.1 specifications. 4.6.1 Global Spanning Tree Parameters Use the Global Spanning Tree Parameters menu to set various STP parameters for the 9155 within the network. See Figure 21 and Table 8. To access the Global Spanning Tree Parameters menu, follow these steps: 1.
Table 8. Global Spanning Tree Parameters Menu Options Menu Item Description 1. Admin Mode Enable or disable STP protocol 2. Version Shows which IEEE specification this meets 3. Configuration Name Name for configuration, typically MAC address, up to 32 characters 4. Configuration Revision Set a revision level between 1 and 65535 5. Priority Set the relative precedence within the STP control structure for the 9155, from 1 (highest) to 65534 (lowest).
4.6.3 Global Spanning Tree Report Use the Global Spanning Tree Report screen to view Global STP parameters and interface statistics and status for the 9155. See Figure 23. To access the Global Spanning Tree Report screen, follow these steps: 1. From the Switch Configuration menu, type 3, "Global Spanning Tree Report," and press . 2. At the Global Spanning Tree Report menu, type 1 to view statistics or 2 to view status for an interface and follow the prompts to select the interface.
SP 1 STATUS Port Identifier : 32769 Port Priority : 128 Port Forwarding State : Manual Forward Port Role : Disabled Port Path Cost : 0 Designated Root : 80 00 00 40 2a 01 10 Designated Port Cost : 0 Designated Bridge : 80 00 00 40 2a 01 10 Designated Port Identifier : 0 Topology Change Ack : False Port Hello Time : 2 Edge Port : False Edge Port Status : False Point to Point Mac Status : True Figure 25. Global Spanning Tree Interface XP x Status Screen 4.6.
4. To return to the Switch Configuration menu, press . VLAN ID 1. 1 VLAN CONFIGURATION TYPE Default NAME Default 1. 2. 3. 4. 5. 6. 7. View/Change Vlan List From Vlan VLAN ID Translation VLAN Priority Translation Create Vlan Delete Vlan Configure Port Vlan : : : : : : : Figure 27. VLAN Configuration Screen Table 9. VLAN Configuration Screen Options Option Description 1. View/Change Vlan Select a VLAN to view in detail 2. List From Vlan Select number to start list of VLANs 3.
GVRP INFORMATION MODE JOIN TIMER LEAVE TIMER LEAVEALL TIMER Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 Disable 20 60 1000 1. GVRP Mode : disabled 2. View/Change Interface : 3. Main Menu PORT/LAG SP 1 SP 2 SP 3 SP 4 MP 1 MP 2 MP 3 MP 4 MP 5 MP 6 MP 7 MP 8 Figure 28. GVRP Information Screen 4.
Table 10. Port Information Menu Options Option 1. View Module Description Select the group of SP or MP modules 2. Port Information View the information and set values for parameters for a selected port 2. Port Statistics 1. 2. 3. 4. 5. 6. 7. 8.
4.8 Report Menu The Report menu shows the current information for the 9155. To access the Report menu, see Figure 32 and Table 11 and follow these steps: 1. From the Main menu, type 4, "Reports," and press . 2. From the Reports menu, type a number to view a report, and press . See Figures 33 through 36. At each report, menu options let you view other pages, clear that log, or return to the Main Menu. 3. To return to the Main Menu, type 4. 1. 2. 3. 4. 5. 6.
SYSTEM LOG Type UserName Description Fan status: All Fans are bad Trap Fan status: Fan module not present Trap Date/Time SYSTEM 10-AUG-2004 13:45:59.30 SYSTEM 10-AUG-2004 13:51:04.59 Figure 34.
4.9 Diagnostics Use the Diagnostics menu for troubleshooting the 9155; you can check the data quality through latency and jitter tests or PING another location. See Figure 38. To use the Diagnostics, follow these steps: 1. From the Main Menu, type 5, "Diagnostics," and press . The Diagnostics menu appears. 2. Type the number for the test option you want, and press . 3. When you finish running diagnostic tests, press to return to the Main Menu.
Table 12. Latency/Jitter Test Definitions Parameter Description 1. Test IP Address Where the 9155 sends the packets 2. Test Duration How long to run the test, in minutes and seconds; 0 means don't stop 3. Test Packets per second How many packets to send each second 4/5. Min/Max Test Packet Size Set the size limits for each packet, from 40 to 1472 bytes 6. Test Packet Timeout How long to wait for a test packet to return 4.9.
4.10 Utilities Use the Utilities screen to set the time and date, restore defaults, reset the system, or start using new firmware. See Figure 41 and Table 13. To access the Utilities screen, follow this step: 1. From the Main Menu, type 6, "Utilities," and press . The Utilities menu appears. 2. From the Utilities menu, type the number for an item and press . 3. To return to the Main Menu, type 5.
4-26 9155 Network Interface Device
Chapter 5 Maintenance and Troubleshooting 5.1 General Maintenance Well-maintained components and clearly identified cables help assure optimum system operation. Damaged fiber cables and dirty connectors are a common source of signal loss or attenuation. Single mode and multimode fiber optics are especially sensitive to contamination. Inspect, clean, and test all components to maintain optimum performance. Note: • • • To avoid damage and signal loss, do not over-tighten or force-fit optical connectors.
5.3.1 Measure Transmitter Output Power To measure the output power, follow these steps: 1. Clean the connectors on the fiber optic test cable, then plug it in to the Tx connector on the 9155. 2. Warm up each component for at least 30 minutes. 3. Set the optical power meter to the proper wavelength. 4. Wait two or three minutes for the power reading to stabilize, and then read the output power. 5.
5.3.3 Measure Fiber Link Attenuation Determine and record link attenuation before starting normal link traffic. The attenuation factor identifies potential problems with links that are on the threshold of receiver limitations. Measure optical fiber links at the shortest wavelength of operation to determine the limiting factor in the loss budget. Each device that transmits to an 9155 has a loss budget that is specified by the manufacturer and recorded on a data sheet provided with the equipment.
5.4.2 New Installation On new installations, make sure that all steps in Chapter 2 are complete, then follow these steps: 1. Check that the STA LED is green. 2. Check that the fiber type (multimode or single mode) matches the 9155 optical mode. 3. Make these checks: • • • • • All fiber cabling is of the same type; do not mix multimode and single mode cables. The fiber optic cable is within the specifications and loss budget of the optic interface module.
Chapter 6 Specifications See also the specifications for the chassis or standalone enclosure. 6.1 9155 Specifications Standards: IEEE 802.3 Dimensions: 1.72" H x 13.375" W x 17.25" D (44 x 340 x 438 mm) Weight: 0.3 lb. (0.136 Kg) Operating Temperature: 0° to 50° C Operating Humidity: Up to 90% (non-condensing) Power Consumption: 5 VDC 800 mA Maximum Optical Connectors: ST or SC Regulatory Compliance • • • • • • • • ETL, cETL & LVD (UL 60950 CAN/CSA C22.2 No.
100 Mbps Optical Interfaces 9501-442 100BASE MX 1310 nm MM 11 dB SC 9501-642 100BASE SD 1310 nm SM 10 dB SC 9501-648 100BASE XD 1310 nm SM 26 dB SC 9501-748 100BASE EX 1550 nm SM 26 dB SC Multiport 100 Mbps Optical Interface 9508-442 MP 100BASE MX 1310 nm MM 11 dB SC 9508-642 MP 100BASE SD 1310 nm SM 10 dB SC 9508-648 MP 100BASE XD 1310 nm SM 26 dB SC 9508-748 MP 100BASE EX 1550 nm SM 26 dB SC 1000 Mbps Optical Interfaces 9501-627 1000BASE SX 850 nm MM 6 dB SC 9501-528 1000BASE LX 1310 nm
Appendix A Warranty Limited Lifetime Warranty Effective for Products Shipped February 1, 2003 and After, Canoga Perkins warrants that, at the time of sale, and, for its lifetime, with certain exceptions noted below, every Canoga Perkins' labeled product purchased will be free from defects in material and workmanship for its lifetime, if properly installed and used in conformity to Canoga Perkins' published specifications. This warranty covers the original user only and is not transferable.
Limitations Canoga Perkins may at its sole discretion modify its Limited Warranty at any time and from time to time. Other than those expressly stated herein, THERE ARE NO OTHER WARRANTIES OF ANY KIND, EXPRESSED OR IMPLIED, AND SPECIFICALLY EXCLUDED BUT NOT BY WAY OF LIMITATION, ARE THE IMPLIED WARRANTIES FOR FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY.
Appendix B Acronym and Abbreviation List FPGA Field Programmable Gate Array GARP General Attributes Registration Protocol for registering a client station in a multicast domain GVRP GARP VLAN Registration Protocol for registering a client station in a VLAN Lag Link Aggregation Protocol LLF Link Loss Forwarding LNK Link MMF Multimode Fiber MST Multiple Spanning Tree PHY Physical Layer RMTF Remote Fault Rx Receive signal SM Single Mode SMF Single Mode Fiber SNMP Simple Network Manag
CANOGA PERKINS CORPORATION 20600 Prairie Street Chatsworth, California 91311-6008 USA Phone: (818) 718-6300 FAX: (818) 718-6312 Web Site: www.canoga.com Email: fiber@canoga.
