User’s guide « FCC » DECLARATION OF CONFORMITY FCC rules - PART 15 NUM’AXES declares that the training collar DOGTEK CANICOM 200 complies to all dispositions of the part 15 of the FCC rules This device complies with part 15 of the FCC. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interferences that may cause undesired operation.
WARNING Any person with individual device for cardiac assistance (pacemaker, defibrillator) must take precautions when they use CANICOM 200. This device emits some static magnetic fields (a magnet is located in the remote control). (Frequency= 915 MHz, at = 0.75 mW). The device complies with Part 15 of the FCC rules. Any technical changes or modifications on the receiver collar or on the remote control not expressly approved by the manufacturer shall void the user’s authority to operate the equipment.
Index ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ Page Contents of the product ................................................................................................. 4 Description of the product .............................................................................................. 4 First use from new ........................................................................................................ 4 How to use the remote control .......................................................
● Contents of the product Inside the packaging you will find: ▪ ▪ ▪ ▪ ▪ ▪ ▪ ▪ 1 receiver collar CANICOM fitted with short contact points 1 lithium 3 Volts CR2 battery for the collar 1 remote control CANICOM 200 fitted with 1 lithium 3 Volts CR2430 battery 1 neon test lamp 1 pair of long contact points 1 carry strap 1 DVD This user’s guide ● Description of the product On/Off switch Continuous stimulations limited to 8 seconds Flash stimulations lower than 1 second 2 contact points (short or long) LCD sc
Polarity « - » of the battery Seal Diagram 4 Activate/deactivate the remote control Remote control is supplied with battery fitted. ▪ ▪ Activate: press the On/Off red button ( ) located on the side of the remote control for 1 second (ref. Diagram.1). Indications appear on the LCD screen. Deactivate: press the On/Off red button ( ) of the remote control for 1 second (ref. Diagram.1). The LCD screen is off.
IMPORTANT: before beginning the coding (first use of the receiver or re-coding), make sure no other person is using his CANICOM 200 or other products from the DOGTEK range close by: your receiver collar could accidentally record the code of his remote control. If that occurs, re-code the remote control with the receiver collar. CODING PROCEDURE FOR THE 1ST USE 1. Activate the remote control: press for 1 second the On/Off red button ( ) located on the side of the remote control. 2.
« + » and « - » : control buttons Use the “+”/”-“ buttons for rapid adjustment of the stimulations level of the receiver collar. 9 levels are available. Level 1: very weak stimulation – Level 9: strong stimulation ● Checking/replacing battery of remote control The performance (radio range) of the remote control may deteriorate as batteries become weak. Be prepared to replace the battery.
Two different series of contact points are supplied. The length of the contact points must be sufficient to have proper contact with the dog’s skin, enabling the device to operate correctly. If you have a long-haired dog and the short contact points fitted to the collar in the factory are inadequate, remove and replace them with the long ones supplied with the kit. Carefully tighten them manually (do not use a key).
− Choose a familiar area, a place your dog is used to. − Always start with beep and define the level of impulse from which your dog reacts by starting with the level of the lowest intensity and increasing gradually. − Choose the right moment to press the button: at the exact time your dog does something wrong. − Give your dog plenty of encouragement: it will learn fast and his desire to respond will only increase. ▪ Do not hesitate to contact a professional trainer for any further advice.
If you encounter any problems, re-code the receiver collar (ref. re-coding procedure). Reinitialize the system by removing the battery from its housing, then with a metallic tool (e.g. screwdriver, scissors) touch each of the 2 battery contacts for 2 seconds approximately (ref. Diagram 7). Insert the battery again: one beep is emitted, indicating the battery is in correct position. Restart your CANICOM using the remote control.
- 7 months in stand by: for a use of 4 hours a day 2 months in continuous use: about 10 000 stimulations of 2 seconds at level 9 To increase the battery life of the receiver collar, we recommend you to deactivate the unit if you are not using it for a long period. ● Warranty DOGTEK guarantees the product against manufacturing defects for the life of the product (conditions applies). Return transport costs for the product will be the purchaser’s sole responsibility.
Use this space to record the serial number of your CANICOM 200 (the number is near the barcode): Transmitter: ………………………………………………………………………………………………… Receiver:…………………………………………………………………………………………………….. www.dogtek.
