EN
Thank you for choosing this product. We are proud to offer the ideal product for you and the best complete range of home appliances for your daily routine. Contents 1. GENERAL SAFETY RULES Carefully read this manual for correct and safe appliance use and for helpful tips on efficient maintenance. 2. WATER CONNECTION 3. LOADING THE SALT 4. ADJUSTING THE UPPER BASKET (ONLY ON SOME MODELS) Only use the dish washer after carefully reading these instructions.
sensorial or mental capacities, without experience or knowledge of the product, only if supervised or provided with instruction as to the operation of the appliance, in a safe way with awareness of the possible risks.
Make sure carpets or rugs do Ensure that the dishwasher does not crush power cables. not obstruct the base or any of the ventilation openings. In general it is not advisable to use adaptors, multiple plugs and/or extension cables. After installation, the appliance must be positioned so that the plug is accessible. Do not leave the door open in WARNING: a horizontal position, in order to avoid potential dangers (e.g. tripping).
By marking this product, we confirm, under our own responsibility, full compliance of this product with all relevant safety, health and environmental requirements under European legislation. dishwasher by the door; during the transport, never lean the door on the trolley. We recommend two people lift the machine. The dishwasher is designed for normal kitchen utensils.
2. WATER CONNECTION If the dishwasher is connected to new The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused. pipes or to pipes which have not been inuse for a long time run water through for a few minutes before connecting the inlet hose. In this way no deposits of sand or rust will clog up the water inflow filter. The inlet and drain hoses can be directed to left or right.
A device located on the supply tube that stops water flow if the tube deteriorates; in this case, a red mark will appear in the window "A" and the tube must be replaced. To unscrew the nut, press the one-way lock device "B". All the dishwashers are equipped with an overflow safety device which, if water exceeds normal levels due to malfunctions, automatically blocks water flow and/or drains excess quantities. SOME MODELS may include one or more of the following features: WATERBLOCK (fig.
Connecting the outlet hose The outlet hose should disharge into a The hose can be hooked over the side of standpipe, making sure that there are no kinks (fig. 6). the sink, but it must not be immersed in water, in order to prevent water from being syphoned back to the machine when this is in operation (fig. 6Y). The standpipe must be at least 40 cm above floor level and it must have an internal diameter of at least 4 cm.
After loading the salt, YOU MUST run a complete washing cycle, or the PRE-WASH/COLD RINSE/REFRESH programme. (Fig. A "1") The appearance of white stains on dishes is generally a warning sign that the salt container needs filling. The salt dispenser has a capacity of between 1.5 and 1.8 kg and, for efficient use of the appliance, it should be refilled from time to time . On the bottom of the machine there is a container for the salt for regenerating the softener.
4. ADJUSTING THE UPPER Type "B": (ONLY MODELS WITH EASY CLICK): BASKET (ONLY ON SOME 1. Remove the upper basket; 2. Hold the basket on both sides and lift it MODELS) upwards (fig. 1). If 29 cm to 32.5 cm plates are regularly Dishes that are greater than 20 cm* in diameter can no longer be loaded onto the upper basket, and the mobile supports cannot be used when the basket is in the upper position.
Using the upper basket The upper basket is provided with mobile A standard daily load is represented in figs. 1 and 2. Upper basket (fig. 1) racks hooked to the sides of the basket, which can be regulated into 4 positions. In the lowered position (A-A1) the racks may be used for such items as: tea and coffee cups, kitchen knives and ladles. Also glasses with stems may be safely hung on the ends of the racks.
Place the cutlery in the plastic cutlery holder with the handles pointing upwards and place the cutlery holder on the lower basket (fig. 6) making sure that the cutlery does not get in the way of the rotating arms. Upper basket (fig. 5) The lower basket is fitted with a special adjustable central rack (fig. 3 and 4). This permits stable and optimum loading, even when the size and/or shape of the dishes is non-standard.
The lower basket has a safety-stop device, for its safe extraction, also especially useful with a full load. For loading salt, cleaning filter and for ordinary maintenance, the complete extraction of the basket is necessary. Cutlery basket (fig.7) The cutlery basket is made with two detachable parts which will enable various loading options. The two parts can be detached by sliding the left section away from the right section. The top of cutlery basket can be removed, for enable various loading options. 6.
7. LOADING THE DETERGENT (Fig. A "2") The detergent It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid,gel or tablet form. Unsuitable detergents (like those for washing up by hand) do not contain the proper ingredients for use in a dishwasher, and stop the dishwasher from working correctly. After pouring the detergent into the container, close the lid, firstly pushing (1) and then pressing on it (2) until you hear the click.
8. TYPES OF DETERGENT read carefully and follow the manufacturer’s Detergent tablets the effectiveness of detergents containing Detergent tablets of different manufacturers dissolve at different speeds, for this reason, during short programmes, some detergent tablets may be not fully effective, because they are not completely dissolved. If these products are used, is recommended to choose longer programmes to guarantee the complete use of the detergent.
9. LOADING THE RINSE AID (Fig. A "3") The rinse aid The rinse aid, which is automatically released during the last rinsing cycle, helps the dishes to dry quickly and prevents spots and stains forming. Filling the rinse aid container. The rinse aid container can be found to the left of the detergent container (fig. A "3"). To open the lid, push the reference mark and, in the same time, pull the tab of opening. It is always advisable to use rinse aid that is specifically designed for dishwasher.
10. CLEANING THE FILTERS EN (Fig. A "4") The filter system consists of: A. A central container that traps the larger particles; B. A micro filter, located beneath the gauze, that traps the tiniest particles ensuring a perfect rinse; C. A flat gauze that continuously filters the wash water. To achieve excellent results every time, the filters should be checked and cleaned after each wash. To remove the filter unit, simply turn the handle anticlockwise (fig. 1).
11. PRACTICAL HINTS If you want the dishwasher to give a How to get really good wash results. Before placing the dishes in the dishwasher, remove any remaining food (bones, shells, pieces of meat or vegetables, coffee grounds, skin of fruit, cigarette ash, thooth picks etc. to avoid blocking the filters, water outlet and washing arm nozzles. Try not to rinse the dishes before loading them into the dishwasher.
2) wash the rotor arms under a jet of water to clear any blockage in the spray heads. Looking after your appliance correctly can extend its lifespan. Do not use tools that can deform the spray heads. Cleaning the appliance’s exterior 3) when you have finished, refit the rotor arms in the same position, remembering to re-align the arrow and screw into position. Disconnect the machine from the power supply.
If the machine is not going to be used for some time, it is advisable to follow these rules: 1. do an empty wash with detergent in order to clean the machine of any deposits; 2. pull out the electric plug; 3. turn off the water tap; 20 4. fill the rinse aid container; 5. Ieave the door ajar; 6. keep the inside of the machine clean; 7. If the machine is left in places where the temperature is below 0°C any water left inside the pipes may freeze.
L "TABS" light M "Wi-Fi" light D DISPLAY E "TABS" option button Fuse / Power input / Supply voltage Capacity with pans and dishes Water supply pressure (MPa) Place settings (EN 50242) 120 Depth with door open (cm) 12 117 59,8x82x58 13 WITHOUT WORKTOP 8 people 8 people 14 117 59,8x81,8 ÷ 89,8x57 15 See rating plate 16 EN 9 people 117 59,8x81,8 ÷ 89,8x55 FULL-INTEGRATED BUILT-IN 9 people 9 people Min. 0,08 – Max. 0,8 TECHNICAL DATA (See rating plate) 60x85x60.
15. PROGRAMME SELECTION AND SPECIAL FEATURES Close the door (after an audible signal has sounded, the programme will start automatically). ON/OFF button To turn the appliance on and off, press the ON/OFF button (for at least 3 seconds). At the end of the cycle, remember to switch off the appliance using the ON/OFF button, then remove the plug and close the water supply. WARNING In the event that the machine remains switched on without selecting or starting any program, after 5 mins.
ADDISH (possibility of adding dishes after the programme has started) pressing the "SMART DOOR/EXPRESS" and "TABS" buttons. To adjust the SOFTENER see the specific Chapter of the manual. To adjust the BUZZER see the specific paragraph. To adjust the MEMO FUNCTION see the specific paragraph. "AUTOMATIC" programmes (only on some models) When the programme starts, you should only open the door and add more dishes when the ADDISH indicator light is switched on.
Changing a running programme. Proceed as follows to change or cancel a running program: Open the door. Keep the START/RESET button pressed for at least 3 seconds. "RESET" will appear on the display and acoustic signals will be emitted. The running programme will be cancelled. At this point a new programme can be set using the "PROGRAMME SELECTION" button. Option buttons WARNING: Before starting a new programme, you should check that there is still detergent in the dispenser.
WARNING Once selected, this option keeps being on (light on) also for next washing cycles and it can be deactivate (light off) only by pressing the button once again. This option is recommended when using the RAPID 24' program, the duration of which will be extended for about 15 minutes, allowing the detergent tablets to achieve a better performance. WARNING This function will only be automatically activated with the "ECO" programme.
When the delay is set on a programme: - after pressing "START/RESET", the countdown time “00:00” appears on the display with flashing “ : ” - if you press any button (except for the "ON/OFF", "PROGRAMME SELECTION" buttons), the programme name is displayed for a single scroll on the display and then the delay time is displayed again. - When the time has elapsed, the programme name is displayed for a single scroll on the display and the remaining time will be displayed as "0:00h".
on the display and the indicator lights of the "SMART DOOR/EXPRESS" and "TABS" buttons will be on. Pressing the "PROGRAMME SELECTION" button until the "MEMO FUNCTION" parameter is selected. Parameter adjustment is performed by pressing the "SMART DOOR/EXPRESS" and "TABS" buttons to change the value from "MEMO MODE ON" to "MEMO MODE OFF" and vice versa. 1. Open the door. "ON/OFF" button for 3 secs to confirm the new setting. 2. Turn on the appliance ON/OFF button.
16. REMOTE CONTROL (WI-FI) Successful enrollment This appliance is equipped with Wi-Fi technology that allows the machine to be remote controlled via an app. App. Download the Candy simply-Fi app onto your device. Unsuccessful enrollment If enrolment fails (or does not succeed within 5 mins.): The Candy simply-Fi app is available both for Android and for iOS tablets and smartphones. "TRY AGAIN" will appear on the display. The machine will not be connected.
"Wi-Fi" indicator light To exit remote control, press "PROGRAMME Indicates the connection status of the SELECTION" again for 3 secs. When no cycle is under way: product to the home Wi-Fi network. It can be: - SLOW FLASHING: disabled. - The Wi-Fi indicator light will start to flash slowly and the message "REMOTE CONTROL OFF" will appear on the display.
17. PROGRAMME LEGEND Programme Description P1 ECO Programme for normally soiled tableware (the most efficient in terms of its combined energy and water consumption for that type of tableware). Programme standardised to EN 50242. P2 INTENSIVE Once a day - for heavily soiled pans and any other items that have been left all day for washing. P3 NIGHT Quietest washing cycle. Ideal for functioning by night and for taking advantage of reduced energy fares.
P2 INTENSIVE P3 NIGHT P4 UNIVERSAL P5 AUTO WASH P6 DELICATE P7 P8 RAPID 24’ P9 PREWASH ● = Add detergent for prewash ■ = "IMPULSE" Programmes ● - ● ■ - - ● ■ YES YES 75 130 YES N/A YES 55 240 YES N/A YES 60 120 YES N/A YES 75-95 YES N/A YES 85 YES N/A YES 39 YES N/A YES 24 N/A N/A YES 5 N/A N/A - - 55-65 - ■ 45 ● - 60 - - 50 - - - *= only on some models N.B. = the SMART DOOR function is only active if the ‘Express’ option has not been selected.
18. WATER SOFTENER UNIT Depending on the source of the supply, water contains varying amounts of limestone and minerals which are deposited on the dishes leaving whitish stains and marks. The higher the level of these minerals present in the water, the harder the water is. The dishwasher is fitted with a water softener unit which, through the use of special regenerating salt, supplies softened water for washing the dishes. The degree of hardness of your water can be obtained from your water supply company.
If you believe the dishwasher is not working correctly, consult the quick guide provided below with some practical tips on how to fix the most common problems. If the malfunction continues or recurs, contact the Technical Assistance Centre. BUG REPORTS Models with a display: errors are reported by a number preceded by the letter "E" (e.g. Error 2 = E2) and a short audio signal. Models without a display: an error is shown by a sequence of flashes of every LED.
Only models without a display If malfunctions or faults occur when a programme is running, the indicator light that corresponds to the selected cycle will blink rapidly, and an intermittent audio signal will sound. In this case, turn the dishwasher off by pressing the "ON/OFF" button. After checking to make sure the water supply is open, that the drain pipe is not bent and that the siphon or filters are not clogged, set the selected program again.
5. Spray arms are not heard to rotate 6. On electronic appliances without a display: one or more indicator lights flashing quickly CAUSE Excessive amount of detergent Item prevents arms from rotating Filtering plate and filter very dirty Water supply tap turned off Switch off the appliance. Turn on the tap. Re-set the cycle.
N.B.: Should any of the above situations result in a bad wash performance or insufficient rinsing, remove dirt deposits from the dishes by hand since the final drying cycle hardens the dirt, making it difficult to remove with a subsequent wash. If the malfunction continues, contact the Technical Assistance Centre, quoting the model of the dishwasher. This is found on the plate on the upper section of the inside of the dishwasher door, or on the warranty.
This appliance is marked a cording to the European directive 2012/19/EUon Waste Electrical and Electronic Equipment (WEEE). WEEE contains both polluting substances (which can cause negative consequences for the environment) and basic components (which can be re-used). It is important to have WEEE subjected to specific treatments, in order to remove and dispose properly all pollutants, and recover and recycle all materials.
fkhldsk
fkhldsk
- CDIN 2D620PB-80E - 21.06 - 41054083 - IDM s.r.l.
