Installation Instructions

3. Connect ground wire on
fixture to outlet box ground
screw. Connect black wire
from fixture to black wire in
outlet box and connect the
white wire from fixture to white
wire in outlet box.
Note: Do not disconnect wires
that are already connected.
4. Tuck electrical wires into
outlet box and position fixture
over studs or nipple on
mounting bracket assembly.
Secure fixture in place with
star washer(s) and cap nut(s).
Style#1 - Screw the glass ring
flrmly into the fixture socket.
And tighten the thumb screw.
Style#2 - Install proper bulb
type and wattage. Remove the
finishing screws that are
already on your fixture.
Position glass in place and
secure with finishing screws.
Style#3 - Remove spinner nut
from the socket. Place the
glass onto the fixture socket.
Use the special tool that
comes with your fixture to
tighten the spinner nut onto
the socket to secure the glass
in place. Install the proper bulb
type and wattage.
Style#4 -Snap “pop off” head
or glass onto fixture (push, or
push and turn (it depends on
the style of your fixture)).
1. Note: Refer to the
mounting bracket style that
matches the bracket that is
included with your fixture.
Style#1 (Non-Threaded holes)
Loosen hex nut “A” and “B”.
Adjust stud so it clears the
fixture once assembled. Hold in
place with “A” and lock in place
with “B”.
Style#2 (Threaded holes)
Loosen “B”. Adjust stud to
desired length and lock in place
with “B”.
Style#3 (Nipple)
Attach nipple to mounting
bracket and adjust until it will
clear fixture when assembled.
Lock in place using the hex nut.
2. Mount the mounting bracket
to outlet box using outlet box
screws. Make sure the studs or
nipple on the mounting bracket
are facing out from the outlet
box.
INSTALLATION:
STYLE#1
STYLE#2
STYLE#3
STYLE#3
STYLE#2
STYLE#1
Outlet
Box
Star
Washer
Outlet
Box Screws
White
Fixture
Fixture
Black
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
Mounting
Bracket
Stud
Or
Nipple
Cap
Nut
T-9
02/07
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
DO NOT REMOVE INSULATION FROM FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. CONNECT THE GROUND WIRE (BARE COPPER OR GREEN) FROM YOUR FIXTURE TO THE GROUND
WIRE (BARE COPPER OR GREEN) OR GROUND SCREW IN THE ELECTRICAL OUTLET BOX.
CEILING/WALL
TRACK LIGHTING
Ground
Wire
NOTE: Product may not look exactly as shown in figures.
STYLE#1
STYLE#2
STYLE#3
STYLE#4
Fixture
Socket
Glass
Finishing
Screws
Glass
Spinner Nut
Fixture
Socket
Special
Tool
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
TOOLS AND MATERIALS REQUIRED:
Wire Cutters
Wiring supplies
as required by
electrical code
Pliers
Wrench
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English)
1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
Phillips Screwdriver
Studs
Nipple
Hex Nut
“A”
“B”
Studs
“B”
Outlet
box
Outlet
box screws
Ground
wire
Mounting
bracket
Fixture
Socket
Glass
Ring
Thumb Screw
“Pop Off”
Head Or
Glass
Fixture
Socket