Installation Guide

5. Once connections of wires are
completed, carefully tuck wires and wire
nuts into the outlet box making sure no
bare wire (on the black and white) is
visible at the wire nuts. Install the light
fixture to the wall by aligning the hole(s)
in the fixture with the studs or nipple on
the mounting bracket. Secure in place
with cap nut(s) and star washer (s).
6. Install the proper bulb type and
wattage (not included).
Note: Some Fixtures will be complete at
this point.
Note: After Installation, seal around the
top and side perimeter between the
fixture and the wall surface with weather
resistant caulking. The bottom should be
left un-caulked to prevent moisture
build-up.
7. Style#1 - Place the top cap on the
fixture and secure in place by threading
the finial onto the nipple until it is snug.
Style#2 - Assemble the light fixture by
attaching the (2) cap nuts until they are
snug.
Style#3 - Install wire guards by
inserting them in holes in the canopy.
8. After Installation, seal around the top
and side perimeter between the fixture and
the wall surface with weather resistant
caulking. The bottom should be left
un-caulked to prevent moisture build-up.
Apply a small amount of weather resistant
caulking around the side perimeter
between the cap nut and mounting plate.
Imported By: CANARM LTD., 2157 Parkedale Ave., Brockville, Ontario, K6V 5V6, Tel: [phone], Fax: [phone]
Cap Nuts
Cap Nut
Finial
Nipple
Top Cap
O-1
07/12
SAFETY PRECAUTIONS:
OUTDOOR LIGHTING
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED.
3. FIRMLY ATTACH THE FIXTURE GROUND WIRE (BARE COPPER) TO THE MOUNTING BRACKET WITH THE
GROUND SCREW (BY WRAPPING AROUND THE GROUND SCREW) AND THEN CONNECT IT TO THE
HOUSE SUPPLY GROUND WIRE WITH A WIRE NUT.
NOTE: PRODUCT MAY NOT LOOK EXACTLY AS SHOWN IN FIGURES.
QUESTIONS OR CONCERNS CONTACT CANARM AT:
1-800-265-1833 (English) / 1-800-567-2513 (French)
Monday through Friday 8:00 AM to 5:00 PM E.S.T.
INSTALLATION:
STYLE #1
STYLE #2
STYLE #3
Wire Guards
L
I
G
H
T
I
N
G
&
F
A
N
S
E
C
L
A
I
R
A
G
E
S
&
V
E
N
T
I
L
A
T
E
U
R
S
!
“INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS”
“READ ALL INSTRUCTIONS”
“IMPORTANT SAFETY
INSTRUCTIONS”
“SAVE THESE INSTRUCTIONS”
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
Wiring supplies
as required by
the Canadian
Electrical Code
and/or the
Quebec
Electrical code
Electrical Box Screws
(Not Included)
Electrical Box
Mounting
Bracket
Stud
Electrical
Box
“A”
“B”
Studs
House Supply
Ground Wire
Fixture
Ground Wire
Ground
Screw
Ground
Screw
Black Wire
White Wire
1. Install the finial by
tightening the nut and star
washer (optional).
2. Mount the mounting
bracket to outlet box using
outlet box screws (not
included). Make sure the
studs or nipple on the
mounting bracket are facing
out from the outlet box.
3. Position mounting
bracket so that the fixture will
sit level once it is mounted to
the wall. Tighten screws “A”
and “B” to hold in place.
4. Firmly attach the fixture
ground wire (bare copper) to
the mounting bracket with
the ground screw (by
wrapping around the ground
screw) and then connect it to
the house supply ground
wire with a wire nut.
Connect black wire from
fixture to black wire in outlet
box and connect the white
wire from fixture to white
wire in outlet box.
Weather
Resistant
Caulking
Weather
Resistant
Caulking
Rubber
Gasket
Glass
Glass
Finial
Star Washer
Star Washer
Nut
Nut
Rubber
Gasket
Top
Bottom