Installation Instructions

5. Once connections of wires
are completed, carefully tuck
wires and wire nuts into the
outlet box making sure no bare
wire (on the black and white) is
visible at the wire nuts. Install
the light fixture to the wall by
aligning the hole(s) in the
fixture with the studs or nipple
on the mounting bracket.
Secure in place with cap nut(s)
and star washer (s).
6. Style#1 Install proper bulb
type and wattage. Remove the
finishing screws that are
already on your fixture.
Position glass in place and
secure with finishing screws.
Style#2 Remove spinner nut
from the socket. Place the
glass onto the fixture socket.
Install proper bulb type
and wattage.
Style#3 Snap glass onto
fixture (push, or push and turn
(it depends on the style of your
fixture). Install proper bulb
type and wattage.
Style#4 Install proper bulb
type and wattage. Install
decorative ring.
T-13
06/18
SAFETY PRECAUTIONS:
1. TURN OFF ELECTRICAL POWER BEFORE STARTING INSTALLATION OF LIGHT FIXTURE.
2. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
3. FIRMLY ATTACH THE FIXTURE GROUND WIRE (BARE COPPER) TO THE MOUNTING BRACKET WITH
THE GROUND SCREW (BY WRAPPING AROUND THE GROUND SCREW) AND THEN CONNECT IT TO
THE HOUSE SUPPLY GROUND WIRE WITH A WIRE NUT.
4. CLEAN GLASS WITH WATER ONLY.
NOTE: Product may not look exactly as shown in figures.
CEILING/WALL
TRACK LIGHTING
INSTALLATION:
Fixture Head
Decorative
Ring
Glass
Glass
Tool
Fixture
Socket
Spinner nut
Fixture
Socket
STYLE#3
STYLE#4
STYLE#2
Electrical
Outlet Box
Mounting
Bracket
Nipple
Mounting Bracket
Hex
Nut
STYLE#1
Fixture
Socket
Glass
Finishing
Screws
Nut
Star
Washer
Optional
Rod
Swivel
Arm
Shade
Glass
Or
TOOLS AND MATERIALS REQUIRED:
Phillips
Screwdriver
Wire Cutters
Pliers Wrench
!
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS
READ ALL INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
QUESTIONS OR CONCERNS CONTACT AT:
1-800-265-1833 (English) / 1-800-567-2513 (French) Monday through Friday 8:00 AM to 5:00 PM E.S.T.
Wiring supplies
as required by
local electrical
code
Tel: [phone], Fax: [phone]
1. Optional rod for different
length required.
2-head (2” x 1pc + 5” x 1pc)
3-head (2” x 1pc + 5” x 1pc + 11”
x 1pc)
Steps for adding rod.
1.1: Unscrew the head from
the pan by removing the nut
and star washer.
1.2: Screw the rod to the swivel
arm. Tighten firmly the rod
against the pan by nut and star
washer. Ensure the star waster
is in place.
2. Attach nipple to mounting
bracket. Adjust so it will clear
hole in back of fixture and then
lock nipple in place with hex
nut.
3. Attach mounting bracket
to electrical outlet box with
electrical box screws (not
included).
4. Firmly attach the fixture
ground wire (bare copper) to
the mounting bracket with the
ground screw (by wrapping
around the ground screw) and
then connect it to the house
supply ground wire with a wire
nut. Connect the black wire (or
wire with marking) from the
fixture to the black wire in the
electrical box and connect the
white wire from the fixture to
the white wire in the electrical
box.
White
Black
House supply
Ground wire
Fixture
Ground wire
Star
Washer
Cap
Nut
Stud
Or
Nipple
Fixture