Instructions / Assembly

Owners Manual
Spa operation - Azure i212 CS Control Panel
Welcome To A New Dimension In Spa Control Systems.
Quick Start Guide - You can use your Smart Control two ways:
(1) Home Page Single Touch Button Control to turn a function On or
Off, like a Pump, Light, or Mood, without any navigation or additional
steps. (2) Navigation Mode where you utilize the full opportunities on
the Full Color Screen to Setup and Control your Spa. In Navigation
Mode, you can immediately return to the Home Screen by Touching
the Back Home Button, or automatically return to the Home
Screen in a few seconds.
This Section of the Control Panel User’s Manual is intended to be a
Quick Start Guide to get you started in Navigating the Azure i212 CS
Control Panel Menu System.
Home Screen System Control
This is the Home Screen with Canadian Spa Company Logo (Left)
These are the System Control Touch Buttons that are active from the
Home Screen (Right)
When the Home Screen is Displayed, all of the buttons Except the
Back Home Button can be used to Directly Control the Spa Sys-
tem equipment and other functions. The Icons on the bottom of the
Screen indicate that the Functions are turned On, or are Active.
• The Pump Button is the Jet Pump Control Button. In a 2
Pump System, it is the Jet Pump 1 Control Button.
• The Light Button is the Spa Light Control Button.
• The Temp Button is the Water Temperature Control Button.
• The Volume Button is the Audio Volume Control Button.
• The Option 2 Button Opens the Help Navigation Menu. In a 2
Pump System, it is the Jet Pump 2 Control Button.
• The Option 3 Button Opens the Settings Navigation Menu. In
a 2 Pump System, it is the Air Blower Control Button.
• The Select Button Changes from the Home Screen to
Navigation Mode.
Navigation Mode System Control
The Settings Icon on the Navigation Screen is Highlighted (Left)
These are the Navigation Mode Active Navigation Buttons.(Right)
In Navigation Mode, at the Center of the Screen, all of the Icon
Functions can be Scrolled either Left or Right to access any of the
Icon Functions, with the Icons rotating like a wheel. All the Buttons
Except the Option 2 and Option 3 Buttons can be used to Navigate
and Select from the Menu System.
• The Up Button Scrolls Up in the Menu Screens.
• The Down Button Scrolls Down in the Menu Screens.
• The Left Button Moves Left from Settings to the next Icon
Function Left, and Exits Back to the Previous Menu when you are
in a Menu.
• The Right Button Moves Right from Settings to the next Icon
Function Right, and Moves Right to the Next Menu when you are in
a Menu.
• The Select Button is used to Select a Menu Item, or turn an
item On or Off.
• The Back Home Button is used to Return to the Home Screen.
• To use the Light , Temp , Volume , and Pump
Buttons to ControlSpa Equipment and Functions. you must Return to
the Home Screen.
When Navigating the Menus, if the Yellow
Highlighted Menu Bar you are on has an
Arrow at the Right End of the Menu Bar,
use the Right Button to Navigate to the
Next Menu, and use the Left Button to Return to the Previous Menu.
Use the Up Button to Scroll Up to the next Menu Bar Above, or use the
Down Button to Scroll Down to the next Menu Bar Below.
If the Blue Area at the Bottom of the Menu
says More and has Arrows pointing Down
and/or Up, as indicated, use the Down
Button to Scroll from the Bottom Menu Bar to the Next Menu, or the
Up Button to Scroll from the Top Menu Bar to the Previous Menu.
Powering Up Your Spa Control System
This Section of the User’s Manual provides Detailed Instructions for
properly and Safely Powering Up your Spa Control System. Before
you turn ON the Power to your Spa Control System, make sure that
the Spa Water Level is at the Spa Manufacturer’s Minimum required
Operating Water Level.
First turn ON the Branch Circuit Breaker Protecting the Spa and
Control System, and then turn ON the GFCI Protecting the Spa
and Control System.
It will take 3 to 4 minutes for the Software to Load and Control
System to Initialize. After the Power is ON, the Control Panel Button
Backlighting will turn ON, but the Display Screen will remain Black
for about 20 seconds. Then, for the next 20 seconds, there will be a
Screen that shows the Serial and Part Numbers. At about 40 seconds
after the Power is ON, there will be a Screen indicating that the
Software is Loading.