Specifications

TEAM Climate Monitoring Protocol 3.1
57
1. D
D
i
i
s
s
c
c
o
o
n
n
n
n
e
e
c
c
t
t
t
t
h
h
e
e
p
p
y
y
r
r
a
a
n
n
o
o
m
m
e
e
t
t
e
e
r
r
f
f
r
r
o
o
m
m
t
t
h
h
e
e
d
d
a
a
t
t
a
a
l
l
o
o
g
g
g
g
e
e
r
r
.
.
Open the enclosure to get access
to the data logger and disconnect the four cables coming from the pyranometer into the data
logger (usually one into 3H (or 4H), one into 3L (or 3H) and two grounds).
2. R
R
e
e
m
m
o
o
v
v
e
e
t
t
h
h
e
e
p
p
y
y
r
r
a
a
n
n
o
o
m
m
e
e
t
t
e
e
r
r
f
f
r
r
o
o
m
m
t
t
h
h
e
e
l
l
e
e
v
v
e
e
l
l
i
i
n
n
g
g
b
b
a
a
s
s
e
e
.
.
Using the thin Allen wrench (that
comes with the pyranometer), free the pyranometer from the leveling base. Write down the
Serial Number (below the Model label on one side) and the date on the
Sensor
Installation/Calibration Form .
3. I
I
n
n
s
s
t
t
a
a
l
l
l
l
t
t
h
h
e
e
r
r
e
e
p
p
l
l
a
a
c
c
e
e
m
m
e
e
n
n
t
t
.
.
Locate the replacement pyranometer in its housing making sure
that the cable is routed through the slot on one side. Secure the pyranometer by tightening the
screw on the side of the base (using the thin Allen wrench). R
R
E
E
M
M
O
O
V
V
E
E
T
T
H
H
E
E
R
R
E
E
D
D
P
P
L
L
A
A
S
S
T
T
I
I
C
C
C
C
O
O
V
V
E
E
R
R
P
P
R
R
O
O
T
T
E
E
C
C
T
T
I
I
N
N
G
G
T
T
H
H
E
E
S
S
E
E
N
N
S
S
O
O
R
R
(otherwise the data will be useless!).
4. C
C
o
o
n
n
n
n
e
e
c
c
t
t
t
t
h
h
e
e
p
p
y
y
r
r
a
a
n
n
o
o
m
m
e
e
t
t
e
e
r
r
t
t
o
o
t
t
h
h
e
e
d
d
a
a
t
t
a
a
l
l
o
o
g
g
g
g
e
e
r
r
.
.
Route and secure the cable through the
leveling arm and base until it reaches the enclosure. Route through the enclosure making sure
there is enough slack to connect to the data logger. Connect the cables to the terminals where
the replaced-to-be pyranometer used to be (use the cabling diagram for your site to match the
color cables and terminals). Secure the cables inside the enclosure using a grommet and
leaving enough slack so they are not tense.
5. C
C
h
h
e
e
c
c
k
k
t
t
h
h
e
e
L
L
e
e
v
v
e
e
l
l
i
i
n
n
g
g
B
B
a
a
s
s
e
e
.
.
Make sure the new pyranometer is leveled by checking the
bubble in the leveling base. Adjust if necessary using the protruding screws on the leveling
base.
6. R
R
e
e
c
c
o
o
r
r
d
d
t
t
h
h
e
e
s
s
e
e
r
r
i
i
a
a
l
l
n
n
u
u
m
m
b
b
e
e
r
r
.
.
Write down the serial number of the new sensor and the date
and time it was installed on the Sensor Installation/Calibration Form .
7. S
S
e
e
n
n
d
d
t
t
h
h
e
e
s
s
e
e
n
n
s
s
o
o
r
r
h
h
e
e
a
a
d
d
o
o
u
u
t
t
f
f
o
o
r
r
c
c
a
a
l
l
i
i
b
b
r
r
a
a
t
t
i
i
o
o
n
n
.
.
Complete a Sensor Calibration Metadata
Form
(Appendix A.5) for each sensor that is sent out for calibration. Mail the sensor head back
to the manufacturer for recalibration. When the sensor comes back, fill in the rest of the
Sensor Calibration Metadata Form and keep the sensor as a duplicate.
8. S
S
u
u
b
b
m
m
i
i
t
t
c
c
a
a
l
l
i
i
b
b
r
r
a
a
t
t
i
i
o
o
n
n
i
i
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
t
t
o
o
t
t
h
h
e
e
T
T
E
E
A
A
M
M
p
p
o
o
r
r
t
t
a
a
l
l
.
.
Submit forms to the TEAM portal
as soon as technically feasible. See Section 6.5.4 for instructions on uploading the
Sensor
Installation/Calibration
and Sensor Calibration Metadata Forms .
6.5.4 Uploading calibration forms
F
F
o
o
r
r
m
m
s
s
n
n
e
e
e
e
d
d
e
e
d
d
:
:
 Completed
Sensor Installation/Calibration Form
 Completed
Sensor Calibration Metadata Form
Since the sensors have been removed from the field and sent out for calibration at this point, the
Sensor Installation/Calibration Form and Sensor Calibration Metadata Form should have been
completed. To upload this information to the TEAM portal, follow the steps below:
a) Open an internet browser and navigate to the TEAM portal (www.teamnetwork.org).