Specifications

20
TEAM Climate Monitoring Protocol 3.1
F
F
i
i
g
g
u
u
r
r
e
e
6
6
.
.
M
M
a
a
i
i
n
n
c
c
o
o
m
m
p
p
o
o
n
n
e
e
n
n
t
t
s
s
o
o
f
f
t
t
h
h
e
e
C
C
R
R
1
1
0
0
0
0
0
0
d
d
a
a
t
t
a
a
l
l
o
o
g
g
g
g
e
e
r
r
.
.
1. C
C
o
o
n
n
n
n
e
e
c
c
t
t
t
t
h
h
e
e
d
d
a
a
t
t
a
a
l
l
o
o
g
g
g
g
e
e
r
r
t
t
o
o
t
t
h
h
e
e
c
c
o
o
m
m
p
p
u
u
t
t
e
e
r
r
:
:
Using the RS-232-to-USB cable, connect the
data logger to a USB port in the computer (make sure the cable is connected to the RS-232
port in the data logger – not the CS I/O port).
If this is the first time using the RS-232-to-USB
cable, drivers may need to be installed on the computer. Drivers are usually located either on
the CD shipped with the cable or on the cable manufacturer’s website.
2. I
I
n
n
s
s
t
t
a
a
l
l
l
l
t
t
h
h
e
e
m
m
e
e
m
m
o
o
r
r
y
y
c
c
a
a
r
r
d
d
a
a
d
d
a
a
p
p
t
t
o
o
r
r
t
t
o
o
t
t
h
h
e
e
d
d
a
a
t
t
a
a
l
l
o
o
g
g
g
g
e
e
r
r
:
:
The memory card module is a
flattened box labeled C
C
F
F
M
M
1
1
0
0
0
0
. Plug it into the peripheral port of the data logger and fasten
the outside screw to secure it.
3. I
I
n
n
s
s
e
e
r
r
t
t
a
a
m
m
e
e
m
m
o
o
r
r
y
y
c
c
a
a
r
r
d
d
i
i
n
n
t
t
o
o
t
t
h
h
e
e
C
C
F
F
M
M
1
1
0
0
0
0
:
:
Unfasten the screw on the right hand side of
the CFM100 to open the door to the memory card compartment. Insert the special memory
card provided (
(
r
r
e
e
g
g
u
u
l
l
a
a
r
r
m
m
e
e
m
m
o
o
r
r
y
y
c
c
a
a
r
r
d
d
s
s
w
w
i
i
l
l
l
l
N
N
O
O
T
T
w
w
o
o
r
r
k
k
) in the slot. Close the door to the
compartment and tighten the screw.
4. C
C
o
o
n
n
n
n
e
e
c
c
t
t
t
t
h
h
e
e
D
D
a
a
t
t
a
a
L
L
o
o
g
g
g
g
e
e
r
r
t
t
o
o
a
a
B
B
a
a
t
t
t
t
e
e
r
r
y
y
:
:
Any battery that is 12 V DC can be used for the
test (e.g. a car battery). Run two cables coming from the positive and negative poles of the
battery and connect them to the POWER IN12V and G notches in the data logger.
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
:
:
Connect the positive pole of the battery to the 12V notch in the data logger
and the negative pole to the G notch. If there is power to the datalogger you will see flashing
lights on the memory card adaptor.
5. I
I
n
n
s
s
t
t
a
a
l
l
l
l
t
t
h
h
e
e
P
P
C
C
2
2
0
0
0
0
W
W
C
C
a
a
m
m
p
p
b
b
e
e
l
l
l
l
S
S
o
o
f
f
t
t
w
w
a
a
r
r
e
e
i
i
n
n
y
y
o
o
u
u
r
r
c
c
o
o
m
m
p
p
u
u
t
t
e
e
r
r
:
:
This software is included
in a CD that came with the data logger and allows you to set the clock of the data logger and
upload the standard TEAM data collection program. Alternatively, if the CD is lost, PC200W is
also available on the Campbell Scientific website at: http://www.campbellsci.com/pc200w.