Owner's manual
Table Of Contents
- Revision and Copyright Information
- Limited Warranty
- Assistance
- Table of Contents
- 1. Preparation and Siting
- 2. Hardware Installation
- 2.1 Base Foundation
- 2.2 Tower/Pole
- 2.3 Enclosure
- 2.4 Crossarm and Sensor Installation
- 2.5 Communication Peripherals
- 2.6 Lightning Rod Installation
- 2.7 Solar Panel Installation
- 2.8 Battery Installation
- 2.9 Restraining Cables and Sealing/Desiccating Enclosure
- 3. ET Software
- 4. Maintenance, Troubleshooting, and Schematics
- 4.1 Maintenance
- 4.2 Troubleshooting
- 4.2.1 No Response Using the CR1000KD Keypad
- 4.2.2 No Response from Datalogger through SC32B, RAD Modem, or Phone Modem
- 4.2.3 NAN or (INF Displayed in a Variable
- 4.2.4 Unreasonable Results Displayed in a Variable
- 4.2.5 NAN or (INF Stored in a Data Table
- 4.2.6 Communication Problems when using an RF450 Radio
- 4.2.7 Gill WindSonic1-ET Diagnostic Diagnostic Codes
- 4.3 Schematics of Connectors
- Appendix A. T107 Maintenance Log
- Appendix B. PS24 24 Ahr Power Supply and 10 x 12 inch Enclosure
- Appendix C. Exploded Views
- Appendix D. Default Programs
- Appendix E. Step-down Transformer Installation
- Campbell Scientific Companies

Table of Contents
PDF viewers: These page numbers refer to the printed version of this document. Use the
PDF reader bookmarks tab for links to specific sections.
1. Preparation and Siting ................................................ 1
1.1 Siting and Exposure ............................................................................. 1
1.1.1 Wind Speed and Direction ............................................................ 1
1.1.2 Temperature and Relative Humidity ............................................. 2
1.1.3 Solar Radiation .............................................................................. 2
1.2 Installation Tasks ................................................................................. 2
1.2.1 Indoors .......................................................................................... 2
1.2.2 Outdoors ........................................................................................ 5
1.3 Tools Required ..................................................................................... 5
1.3.1 Tools for Pole Installation ............................................................. 5
1.3.2 Tools for Instrumentation and Maintenance ................................. 6
1.4 Supplies for Power and Communications Options ............................... 6
1.5 Determining True North for Wind Vane Orientation ........................... 7
1.5.1 Web Calculator ............................................................................. 8
2. Hardware Installation ............................................... 10
2.1 Base Foundation ................................................................................. 11
2.1.1 Supplied Components ................................................................. 11
2.1.2 Installation................................................................................... 11
2.1.3 AC Power Installation ................................................................. 13
2.2 Tower/Pole ......................................................................................... 13
2.2.1 Supplied Components ................................................................. 13
2.2.2 Installation................................................................................... 13
2.2.3 Tower Grounding ........................................................................ 15
2.2.3.1 Supplied Components....................................................... 15
2.2.3.2 Grounding Procedure ....................................................... 15
2.3 Enclosure ............................................................................................ 16
2.3.1 Enclosure Installation .................................................................. 16
2.4 Crossarm and Sensor Installation ....................................................... 17
2.4.1 Components ................................................................................ 17
2.4.2 Crossarm Installation .................................................................. 17
2.4.3 RH and Temperature Radiation Shield ....................................... 19
2.4.4 034B Wind Sensor (Wind Sensor Option –MW) ........................ 20
2.4.5 Gill WindSonic 2-D Ultrasonic Wind Sensor (Wind Sensor
Option –GW) ........................................................................... 22
2.4.5.1 Changing the Jumper ........................................................ 22
2.4.5.2 Attachment to Sensor Arm ............................................... 24
2.4.6 Rain Gage.................................................................................... 26
2.4.7 Pyranometer ................................................................................ 27
2.4.8 Sensor Connections ..................................................................... 28
2.4.9 Sensor Verification and Clock Set .............................................. 30
2.5 Communication Peripherals ............................................................... 30
2.5.1 Direct Connect to T107 Station ................................................... 30
2.5.2 Phone Modem ............................................................................. 32
2.5.2.1 Internal Installation .......................................................... 32
2.5.2.2 External Installation ......................................................... 33
i










