Operating instructions

9
HVLP Paint Sprayers
Operating Instructions and Parts Manual
gauge, safety valve and connectors
attached), 3/8” black lined fluid hose,
bag of nuts and bolts for assembly, and
instructions.
NOTE: Do not place pressure pot onto
the cart or insert handle into cart base
until the turbine unit is firmly bolted
and secured to the cart. Using the cart
without the turbine installed can result
in the cart tipping over.
ATTACHING TURBINE UNIT TO CART
1. Set the turbine unit on the cart
base plate with the turbine air
hose quick disconnect coupler
facing out.
2. Line up the four holes on the
turbine base plate with the four
holes on the cart base plate.
3. Secure turbine unit to cart base
plate with the four hex bolts,
washers and hex nuts (supplied).
Insert bolt through the holes, place
washer over the bolt on the
underside, screw hex nut onto bolt
and tighten. Be sure that hex nut is
tight enough so as not to vibrate
loose.
4. Insert the chrome handle into the
frame tube. Be sure to push handle
all the way down so that the spring
loaded buttons lock into place,
securing the handle firmly.
5. Plug turbine unit into outlet on
side of the Cart.
4. Place the 2.643 gallon (10L)
pressure pot onto the pressure pot
deck. Align the fluid outlet toward
the front of the cart. This will
position air inlet toward the back
of the cart.
NOTE: Pressure pot support rings can
be adjusted for use with different size
www.chpower.com
HV2100, HV2105
pressure pots.
CONVERT SPRAY GUN FROM CUP
GUN TO PRODUCTION FLUID FEED
1. Remove cup assembly.
a. Disconnect the upper section of
the air feed tube from the non-
Additional
Instructions for
Model HV2105
(Cont.)
return valve, leaving the valve
attached to the lower section of
the tube. This will provide safe
storage while using the spray gun
without the cup in a production
mode.
b. With a wrench, loosen the center
bolt and remove the cup assembly.
Set aside.
c. Remove air feed connector and
upper section of air feed tube
with small wrench.
d. Install the blanking screw
provided (10/32”) to close the hole
where you removed the air feed
connector. Store the air feed
connector with tube attached in
the cup assembly for future use.
ATTACHING AIR HOSE AND FLUID
HOSE
1. Attach turbine air hose to handle
of spray gun with quick disconnect
coupler.
2. Insert the male coupler on the
other end of the air hose into the
quick disconnect coupler on the
turbine unit. 3. On spray
gun, put a strip of PTFE tape
around the threads on the fluid
connector.
4. Screw one end of the black fluid
hose onto fluid connector. Secure
and tighten.
5. Locate paint outlet on lid of the
2.643 gallon (10L) pressure pot
(marked on the pot). Put a strip of
PTFE tape around the threads of
the Fluid Connector.
6. Take the other end of the black
fluid hose and attach it to the
paint outlet (marked on the pot).
Secure and tighten.
7. Locate the compressor under the
Pressure Pot Deck. Take the air
hose from the compressor and
connect the female quick
disconnect to the male connector
(marked air inlet).
8. Your cart system is now set up for
production spraying.
PREPARING TO SPRAY
NOTE: Never open the pressure pot
without turning off the air compressor
and releasing the air pressure in the
pot with the air pressure release valve.
(Open valve until all pressure is
released. Pressure gauge will read “0
psi” when there is no more pressure in
the pot).
1. Prepare your paint or coating for
spraying. Adjust viscosity as
recommended. See page 6 for
viscosity guidelines.
2. Carefully loosen the four wing nuts
to remove the pot lid. Open the
pressure pot. (NOTE: You may have
to disconnect the air hose from the
compressor when opening the lid.
Be sure to reconnect air hose when
the lid is closed again). You can
either pour your coating into the
pot, or you can insert a smaller
container inside the pot, making
sure that the material pick-up tube
is inserted into the coating. Place
the lid back on top of the pressure
pot, making sure that it is properly
seated. Bring each wing nut back
into place and secure the lid firmly.
3. Secure each wing nut into place