Manual for download at www.CamOnetec.com Vers.: 1.
Safety advice WARNING: SERVICE & SUPPORT Follow these instruction to prevent damage of the unit: DO NOT USE UNPROTECTED IF RAIN OR WATER. PREVENT CONTACT WITH ANY KIND OF LIQUIDS USE RECOMMENDED ACCESSORIES ONLY DO NOT DISASSEMBLE THERE ARE NO PARTS AT THE INSIDE THAT NEED TO ME MAINTAINED REPAIRS SHOULD BE MADE BY QUALIFIED PERSONNEL ONLY CamOneTec by ACME Industriestr. 10a 33397 Rietberg Germany Tel: +49 5244 7000 70 service@camonetec.com or http:// www.camonetec.
Content of Box Check the completeness before using the product CamOne Infinity Camera 1080p USB-Cable USB –AV-Cable DiveBox M-Mount Velcro Pad small Ten-2-Ten Adaptor Long connector Short connector Helmet Mount Velcro Pad big 3 Battery Bike Mount Universal Mount Manual
Preparation Compensation for recorded content ACME will not be responsible in any case for any consequential or direct problems that will lead to a loss of recorded or edited data. Furthermore ACME will not guarantee the content in case the recording or saving is not working properly. The above limitations are as well valid in case the unit has been repaired. Do not remove the micro SD Card while recording or saving.
Functional diagram The USB comport has the following setup: -AV-Out -5V IN -Signal IN for external Start/Stop (CarCamOne-Cable / Motion sensor) -GPS-Module / Video transmitter Set data input Due to limitations in the technology of the display production, single or few dark or light dots might appear.
Key Panel – Interface Overview 6
Compatible cards Only use Micro-SDHC-Cards rank „Class4“ or higher. The camera can be used with cards up to 32GB. The recommended cards are "FCO Rapid Rush" cards at a minimum size of 8GB. Using a 32GB card allows a recording time of 4,5 hours at highest resolution. Insert/ Remove Memory Card Remove the comport cover protecting the sockets and the card slot. Slide in the card upside down - printed side to the bottom until it clicks in. Use Slot 1 at first.
Icons at the Display Due to the different configurations, you will see various icons on the display: 8
SETUP Menu Please press the M- Button for 3 seconds to enter the setup. The menu is divided in 3 categories that can be selected by the different tabs (Photo, Video and system settings). By pressing the M- Button you will enter the next tab. Photo-Menu Here you can select all necessary settings for photo recordings.
-Auto Power off: Select the Auto off function: Off, 60 Sec., 120 Sec. or 300 Sec.
Time lapse recording Press the „M-Button“ to enter the setup menu. Choose the video menu and then „Time lapse“. You can choose between: 1 FPS, 6 FPM, 2 FPM or 1 FPM. Confirm the requested function and leave the menu. By pressing the record button you can start the video. By pressing this button again the recording is stopped and will be saved on the memory card. If you are planning to record for a longer time, we recommend to turn off the screen in order to save power (Menu: „Auto Screen off“).
Playback of Videos and Photos To watch your recorded data, press the „Play“ button. You have the choice between photos and videos. Choose this with the Photo and Video button. Confirm your choice by pressing the Play button. To playback the recordings, press „Play“. The display shows the name of the files. Playback on the TV Connect the camera with your TV by using a HDMI Cable and switch to the corresponding channel. Enter the Playback Mode on the camera to watch your videos.
Replacing the lens (optional) To replace the lens, twist off the two screws on the picture shown. Unscrew the lens. Please pay attention that no dust or dirt get into the cam. Screw in the replacement lens. Check the sharpness with a TV. Fix the cam with the two screws. FPV-Kopf für den Please note! Inappropriate opening may damage the camera head and ports. Perform this work very carefully and take your time! LinX 2.
Firmware Update To get the most out of your camera, install the latest software (Firmware). The firmware version of your camera is shown in the system settings. Download the ZIP file from our homepage first. Unzip the file on the main root of the memory card. Enter the system settings of the camera and choose Firmware Update > "Yes" and confirm with the “Play”- button. This process takes about 1 minute. The display shows the procedure.
Troubleshooting Error Camera switches off immediately. Unable to switch ON the camera The Video jerks when playing at the PC. The video is turned 180° Date and time will not be displayed in a correct way Display shows „Error“ Reason Solution Battery is not charged correctly. Battery is not plugged correctly. Charge the camera for at least 4 hours. Check connection between camera and battery. Battery is defective. Replace the battery. The camera had a hangup during recording.
CamOne Infinity HD Accessories Art‐No.: FCHD02 FCHD03 COIN08 COIN10 FCHD15 FCHD16 FCHD32 FCHD43 FC3104 EAN Item 4260033 049520 4260033 049537 4260033041975 4260033049650 4260033 049667 4260033 049827 4260033048578 4260033 048721 FlyCamOne HD Screen 2,5"; 150cm cable FlyCamOne HD Transmission Set 5.8GHz; Range 300m CamOne Infinity Battery LiPo 3,7V 900mAh CamOne LinX 2.
