USER MANUAL BlackSys CH-100B CAMMSYS Blackbox ※ BlackSys Application may vary in function depending on mobile product and OS version.
Thank you for choosing BlackSys. This manual is based on the CH-100B model. The latest firmware & manual can be found at our website www.blacksys.co.kr/en ■ Please read carefully before using this product. ※ This manual should be reviewed and retained for future reference. ※ CAMMSYS Corp. reserves all rights to this manual in accordance with the copyright law. ※ Content of this manual is subject to change without notice to ensure quality control.
Contents contents 01 02 03 Instruction for Use 1-1. Product Precautions 1-2. Installation caution 1-3. GPS caution 1-4. Memory Card …………………… 04 …………………… 07 …………………… 07 …………………… 08 Features …………………… 09 Package & Part Names 3-1. Package Guide 3-2. Front & Rear 3-3. Left & Right 04 …………………… 12 …………………… 13 …………………… 14 Installation 4-1. Front Camera (Main Unit) …………………… 15 4-2. Rear Camera …………………… 17 4-3. Memory Card Usage …………………… 18 05 Product Usage 5-1. Standard Operation Guide ………………… 19 5-2.
01 Product Precaution 1-1 Caution 1. Do not expose product to direct sunlight or cold weather for extended periods of time. Product exposure to direct sunlight and extreme temperatures may cause damage to the product. 2. Do not dismantle or alter the product. Do not disassemble, modify, or attempt to repair the product. Any alterations to the product can void the manufacturer’s warranty. Please contact your local dealer or the C/S Centre for more information. 3.
9. Video quality may vary depending on extreme lighting conditions. Quality is subject to alterations in extreme dark/light areas and conditions. Most notability when entering/exiting a tunnel or parking garage. 10. Data may not be recorded if accident impact is lower than a predetermined threshold. In extreme cases the product may not record data during an accident due to low impact forces. In addition, during a high force impact accident power may be cut off to the product and data may be lost. 11.
19. The left/right side image quality of this product may vary due to characteristics of the wide-angle lens. 21. Please ensure all accessories are connected to product(s) to avoid data loss. 22. The interworking draft using Wi-Fi between smartphone and product cannot be connected simultaneously, also when it is connected with product you cannot access internet. 23. Playing video or any other functions may not operate properly on specific kind of smart phone. 24.
1-2 Installation caution 1. Keep product clear of clutter. Please ensure the surrounding area is clutter free to avoid reflections/vibrations that may reduce the image/audio quality. 2. Ensure camera lens is clean at all times. Allowing the camera lens to collect dust/oils will reduce the quality of the image. 3. Do not attempt to operate or install the product while driving. For your safety, do not attempt to operate or install the product while driving to avoid a traffic accident. 4.
3. External electronic products and window tinting may affect the GPS reception. 4. Vehicle speed accuracy may vary between 1-30km/h depending on the reception area when stopping the car. 5. GPS may be operated when switching off the product. 1-4 Memory Card 1. Do not remove the memory card by force while the product is in recording mode. Please turn off the product before removing the memory card(s).
02 Features + Clear image with CMOS Sensor Front: Full HD Sony CMOS Sensor / Rear: HD Image Sensor + Distortion-free recording with Wide-angle lens Front: 1920x1080p Full HD, 30fps / 16:9 wide screen with 135° angle of view Rear: 1280x720p HD, 30fps with 130° angle of view + Wi-Fi Support (802.11b/g/n (2.4~2/4835FHz)) + Low Voltage Cut-off function Under 100uA Leakage current.
+ 8GB~128GB Memory Support + Multi Language Support Korean, English, Chinese (Mandarin, Cantonese), Arabic, Russian, French, Spanish (Europe, South America), Japanese, Thai language, Bahasa Indonesia, Vietnamese, German, Turkish, Italian, Czech, Portuguese, Bahasa Malaysia + Security LED Support + GPS Dual Band (GPS+GLONASS) + Built-in microphone Product records audio simultaneously with video.
+ Direct memory card format Product formats memory card without connection to PC. + Built-in super capacitor Internal battery replacements are not necessary due to a built-in semi-permanent super capacitor. When the vehicle is turned off, the product will save all data before terminating. + Playing You can check the recorded video and driving information by BlackSys PC viewer and smartphone and also you can use other video player such as Windows media player.
03 Package & Part Names 3-1 Package Guide Standard Components User Manual Main Unit (Product) Cable Holder Micro SD Memory Cigar Jack Cable Option Bracket Rear Camera Wi-Fi Dongle DC Fuse Power Cable OBD Terminal ※ Actual components may be different from pictures and some components can be changed in case. If package doesn’t include below components, please contact a retail shop or company where product was sold.
3-2 Front & Rear Emergency Recording Button Camera Lens Volume Control For manual recording Speaker volume control (+) For video recording Volume Control Speaker volume control (-) MICRO SD Wi-Fi Security LED LED indicator for parking or video recording Wi-Fi ON/OFF Micro SD card slot External Micro SD card port USER MANUAL 13
3-3 Left & Right GPS Port Wi-Fi Port Wi-Fi Connecting port ① GND ② AV OUT ③ GPS Data ④ Power 14 CAMMSYS BLACKBOX OBD Terminal Check location and speed of vehicle through BlackSys Viewer program Check driving information by using OBD cable Rear Camera Connecting Port Power cable port Connecting HD rear camera Cigar jack power cable port
04 Installation 4-1 Front Camera (Main product) 1. Attaching double-sided adhesive tape 2. Installing unit Wipe up the foreign matters or moisture completely from the location of installation. Remove the release paper on double sided tape and attach it to the cradle part of holder and remove the red adhesive protector. Installation is recommended on the left/right of room mirror. Tightly fasten the adhesive of holder to the windshield by pushing it.
4-1 Front Camera (Main product) 3. Power cable arrangement and connection 4. Power cable connection and check the LED state By using the cable holder, arrange the Cigar jack cable and connect it to the DC IN port. After inserting the Cigar jack cable into cigar jack, turn on the car ignition. If all LEDs of power status are on, installation is completed.
4-2 Rear Camera 1. Rear Camera Installation 2. Installation Connect rear camera to the rear camera connector. Clean up the cable of rear camera from the location of installation. Wipe up the foreign matters or moisture completely from the location of installation. Remove the red adhesive on double sided tape and attach it to the rear windshield. Installation is recommended on the middle of rear windshield. ※ Tinted windows may cause unclear image of video from rear camera. Avoid tinted window.
4-3 Memory Card Usage - Video is recorded in 3 or 5 minute intervals for continuous recording. 30 second intervals for motion and event recording. - The number of files and usage times below is standard when set at 70% continuous, recording, 20% motion recording and 10% event recording. 1.
05 Product Usage 5-1 Standard Operation Guide 1. Recording start and end - Once connecting power, CH-100B gives voice guide, “Start recording” and then it starts recording. - Once disconnecting power, CH-100B gives voice guide, “Car DVR is ending”. ※ Please check whether the SD card is inserted into the main unit or not before connecting power. 2.
4. Normal Recording - Normal recording : Recording starts when vehicle power is turned on and recorded data are stored in SD card. (“AlwaysMovie” folder) - Event recording : Recording starts if acceleration sensor(G-sensor) detects impact, sudden unintended acceleration and quick braking, it records 30 sec. of video to the (“EventMovie” folder)(10 sec. before and 20 sec. after the event) - Manual recording : Recording starts if user manually pressed the vent button during the car runs, it records 30 sec.
※ You can set the motion detection function on the BlackSys Viewer : Configuration Settings >> Notion Detection. Or directly from the BlackSys App : BlackSys Settings >> Motion Detection. ※ White LED will blink while motion recording is active. ※ Motion detection may fail when the vehicle is in extreme lighting conditions. ※ Recording time during parking mode may vary depending on the vehicles’ battery voltage.
5-2 LED Indicator and Voice Guide ※ Function can be changed according to product upgrade.
- Hardware (H/W) Status LED LED Rear camera GPS Red(REC) Connect / Disconnect Green(Rear) Blue(GPS) Yellow(Wi-Fi) Connecting rear camera while operating / Rebooting when disconnecting Connection success ON ON(2CH) ON - Connection failed ON ON(2CH) OFF - ON ON ON(2CH) - ON OFF ON ON(2CH) - OFF Wi-Fi - Security Status LED LED Parking Mode Red(REC) Green(Rear) Blue(GPS) Yellow(Wi-Fi) Security LED Standby ON ON(2CH) ON(Connecting) ON(Connecting) Blink 3sec.
- Operating button (Option Key), Long Key (More than 3 sec.) Function Key Voice Guide Event Button Long Key Formatting is on standby. Press the left key to format Event Button Long Key Formatting the SD card. Do not turn off the power.
5-3 Using BlackSys App 1. Start and end recording ※ Download the BlackSys application on your smartphone. The BlackSys application can be found on the Google Play Store and The App Store for iPhone. - The BlackSys application can be used with Android 4.2 or later, iOS 5.0 or later. - The BlackSys App may not be supported depending on the smartphone. ※ Turn the Wi-Fi button located at the bottom of the product.
5-4-1 Using BlackSys App - SD Card ※ You can view your recorded footage saved on the SD Card right from the BlackSys App. 1. Navigation : Navigate to the Main Screen 1 2. Front Camera : Display all footages except Front Camera 2 8 3 4 5 6 7 9 3. Rear Camera : Display all footages except Rear Camera 4. Always Video : Display all footages except Always Recording mode 5. Event Video : Display all footages except Event Recoding mode 6.
5-4-2 Using the BlackSys App - BlackSys Connection ※ Connect with your BlackSys product to view captured footage. ※ Green indicates a successful connect on the Main Screen. 1. Navigation : Navigate to the Main Screen 1 11 2 12 2. Front Camera : Display footage captured by the Front Camera 3. Rear Camera : Display footage captures by the Rear Camera 8 9 3 4. Always Video : Display footage captured in Always Recording mode 4 5. Event Video : Display footage captured in Event Recoding mode 5 6 6.
5-4-3 Using the BlackSys App - Configuration ※ Configuration only available when BlackSys product is connected to your Smartphone. ※ Menu items may vary depending on BlackSys model. ※ While saving changed value, either black box and smart phone have to be turned on. 1 2 1. Navigation : Navigate to the Main Screen 2. Save Changes : Changes will be saved and applied 3 4 3. Video : Configure video settings 5 6 4. Basic : Configure basic settings & functions 7 8 5. GPS : Configure GPS settings 9 6.
5-4-4 Using the BlackSys App - Miscellaneous 1 2 3 4 5 6 1. Navigation : Navigate to the Main Screen 2. Application Version : Displays current mobile app version 3. Firmware Download : Download the latest firmware 4. Firmware Version : Displays current firmware version of your product 5. Call Service Center : Contact BlackSys for more information 7 6. YouTube : View our YouTube channel 7. BlackSys Homepage : Visit our homepage for more information 5-5 Upgrading Firmware on the BlackSys App 1.
5-6 BlackSys Viewer 1. Program Installation - BlackSys Viewer can be found on the SD card(s) that come with your product. ※ You can download the BlackSys Viewer from our webpage www.blacksys.co.kr/en > GET SUPPORT > Download and execute. Once installation is completed, click BlackSys Player and execute it. CH-100B Player 2.
3. PC Viewer Instructions Time configuration Configuration Save recorded video Print recorded image Folder open Map View Play List Play list and event information Front view indicator icon File name of front view video : alwa_20141112_071532_F.avi Mian Viewer screen Rear view indicator icon File name of rear view video : alwa_20141112_071532_R.avi File name of rear view video G-Sensor Data Review Move to 10sec. before Pause Move to 10sec.
4. Configuration - User can change the default setting value such as recording, system, time and more options using “Configuration” on the PC viewer program menu.
5.
06 Firmware Update 6-1 Firmware Update Please follow the below process in case of updating firmware. ① Remove SD card from the unit. • Turn off the ignition first and remove cigar jack cable from the unit. ② Access our webpage (www.blacksys.co.kr/en > GET SUPPORT > Download) and download the latest update file. ③ Connect SD card to PC and paste downloaded latest update file (CH100update.zip) to the root of removable disk. ④ Insert SD card which contains latest update file to the unit.
07 How to format SD card 7-1 PC format 1.PC format ※ “How to format?” is provided from PC viewer. We do not recommend to format on “My Computer”. ① Insert or connect SD card to PC. ② Click [Start] → [My Computer] ③ Place mouse pointer on [Portable USB drive] SD card and click the right button of mouse. Then click the [Format] ④ Once click the [Start] button, format is started. • FAT 32 format is required if SD card recognition and record error happen.
08 Technical Specification ※ Technical Specification can be changed without prior notice for product improvement. Feature Feature Description Feature Camera Front: Full HD 2.1M Pixels Sony CMOS Sensor (1/2.9”) Rear: HD 1.0M Pixels COMS Sensor (1/2.9”) Shock Sensor Angle of View Front: 135°/ Horizontal(107°), Vertical(55°) Rear: 130°/ Horizontal(105°), Vertical(54°) Bitrate & Frame Front: 6Mbps 30fps Rear: 4Mbps 30fps Video & Audio Format H.
09 Customer Service ※ We don’t take any responsibility for the data loss during the service. Please back up the date before applying for service. CammSys Customer Service - Address: 3F Daeil B/D, 681-17, Yeoksam-dong, Gangnam-gu, Seoul, 135-081, Korea - Opening hour: 09:00 ~ 18:00 (Mon. ~ Fri.) -Closed: Saturday, Sunday and Public Holiday If you come to customer service center, service personnel will care for the service timely and properly.
10 Quality Assurances 1. Warranty period • Product(main unit) : 12 months from the purchase date (But, if purchase date is not clear, it can be applying 3 months warranty after manufacturing date) • Accessory(expendable supply) : 6 months including SD card.
11 Product Warrarnty Model Name CH-100B Manufacturer Cammsys Co.,Ltd Serial No. Purchase Date Warranty Period 12 months from the purchase date (But, if purchase date is not clear, it can be applying 3 months after manufacturing date) Name Tel. Customer Information Address Assembler information Shop name Tel. ※ The warranty for the product is benefited by the details on the warranty card. ※ Warranty period is counted from the purchase date. So get the purchase date.
Daeil Bldg 3F, 681-17, Yeoksam-dong, Gangnam-gu, Seoul, Korea Tel. 070-4680-2599 / Fax. 070-8668-1161 / www.cammsys.net / www.blacksys.co.kr/en / www.mycar365.net m.0.1.
