Specifications

6
7
T.C.A.
ZL56
SENS.
FUS. MOTORE 7.5A
2
1
ON
FUS. ACC. 3,15A
FUS. CENTR. 315mA
APR
E
AP / CH
AF
0V
230V
0
17
26
BIANCO - WHITE - BLANC - WEIß - BLANCO
MARRONE - BROWN - MARRON - BRAUN - CASTAÑO
VERDE/GIALLO - GREEN/YELLOW - VERT/JAUNE
GRÜN/GELB - VERDE/AMARILLO
BIANCO - WHITE - BLANC - WEIß - BLANCO
NERO - BLACK - NOIR - SCHWARZ - NEGRO
ROSSO - RED - ROUGE - ROT - ROJO
VERDE - GREEN - VERT - GRÜN - VERDE
26V17V 0V
M N
+
E -
ENC/RADIO
MARRONE - BROWN - MARRON - BRAUN - CASTÀÑO
VERDE - GREEN - VERT - GRÜN - VERDE
ROSSO - RED - ROUGE - ROT - ROJO
2
1
3
4
5
6
8
7
9
10
11
12
13
14
15
16
17
Technical description
The card is powered with a 230V (AC) power outlet and its
input is protected with a 1.6A line fuse. The motor is protected
with a 7,5A fuse. Control systems are powered by low voltage
and protected by a 315mA fuse. The total power consumption
of 24V accessories (which are protected by a 3.15A fuse) must
not exceed 40W.
Fixed operating time of 80 sec.
Safety
Photocells can be connected to obtain:
- Re-opening during the closing cycle (2-C1), the photocells
on detecting an obstacle while closing the door, cause the
movement direction to be reversed until opening is complete;
- Total stop (1-2), stop of the garage-type door with the
exclusion of the automatic closing cycle. To resume the
movement, use the pushbutton or the radio control;
- Amperometric safety device
: when an obstacle is
encountered, the amperometric device causes the reversal of
movement direction during both opening and closing.
N.B.: if an obstacle is detected three times, the door wing stops
during aperture, and automatic closure is disactivated.
Use the keyboard or the radio transmitter to resume movement
of the bar.
Other functions
- Automatic closing. The automatic closing timer is automatically
activated at the end of the opening cycle. The preset,
adjustable automatic closing time is automatically interrupted
by the activation of any safety system, and is deactivated after
a STOP command or in case of power failure;
Caution! Shut off the mains power and disconnect the
batteries before servicing the inside of the unit.
ZL56 CONTROL PANEL
- Type of command:
-«open-stop-close-stop» for pushbutton and radio
transmitter;
Accessories connected
- Courtesy Light
(24V-25W). A light that illuminates the
manoeuvring zone; after an opening command, the light
remains on for a xed time of 2 minutes and 30 seconds.
Optional accessories
- Flashing signal light
when gate is in motion (24V-25W max.),
connect it to terminal blocks 10-E;
- AF radiofrequency board (see table on pg. 24) for remote
control.
Adjustments
- Trimmer TCA = adjustment automatic closing time;
- Trimmer SENS = adjustment sensitivity of amperometric
safety system.
Important: after powering up the system or after a total-stop,
the 1
st
movement is always the opening manoeuvre. During
this stage it is not possible to close the door. It is possible to
re-close it after the door completes the opening manoeuvre.
MAIN COMPONENTS
1 - Line fuse, 1,6A
2 - Location for emergency batteries
3 - Gearmotor
4 - Transformer
5 - Transformer connection terminal board
6 - Motor fuse, 7,5A
7 - Gearmotor and encoder connection terminal board
8 - Functions control LED
9 - Buttons for saving radio code, manoeuvre and encoder
programming
10 - Trimmer TCA: automatic closing time adjustment
11 - Trimmer SENS: amperometric sensitivity adjustment
12 - 2-dip function switch
13 - Courtesy Light
14 - Accessoires fuse, 3,15A
15 - Central control unit fuse, 315mA
16 - Accessory and control connection terminal board
17 - “AF” radiofrequency board socket